Microwave cavity perturbation technique: Part III: Applications

The resonant cavity perturbation method as described in the preceding two parts of this series is applied to study the electrodynamical properties of different materials in the microwave and millimeter wave spectral range. We briefly discuss the relevant uncertainties which are asociated with the different measurement techniques and we find that employing the amplitude technique it is possible to measure both the width and frequency to nearly the same precision. We then demonstrate the broad range of applicability of this technique by showing results obtained on several different materials, ranging from an insulator to a superconductor. The performance limitations of this technique are discussed in detail.     

Comment on “A numerical investigation of the acoustic mode waves in a deviated borehole penetrating a transversely isotropic formation”

正In the paperA numerical investigation of the acoustic mode waves in a deviated borehole penetrating a transversely isotropic formationby Liu et al.[1]numerical experiments are reported for a dipole sonic logging scenario with a deviated borehole penetrating a VTI anisotropic medium.In such a situation it is important to clearly define the meaning of group and phase velocities as this has led to much confusion in the literature as discussed by Miller,Horne and Walsh[2].     

The use of contact angle measurements to estimate the adhesion propensity of calcium carbonate to solid substrates in water

We have studied a series of solids using contact angle measurements; stainless steel, gold, aluminium, titanium nitride and PTFE that are frequently used in domestic water environments. It was found the influence of electron-donor (γ⁻) and electron-acceptor (γ⁺) free energies on material scaling rate was dominated by water wetting angles, providing materials exhibit an average roughness below 100 nm. The γ⁻ component had the greatest influence on theoretical adhesion, while γ^LW, (Lifshitz-van der Waals) γ⁺ and γ^AB (acid-base) had little effect. From the materials analysed, amorphous carbon coatings were least adhesive, while ‘kettle coating’ and highly roughened steel the most adhesive. The size and distribution of asperities also influenced the polar free energies and subsequent adhesion due to fluctuations in the wetting angle. The results obtained indicate works of adhesion can be used as a complementary technique with Lewis acid-base theory to deliver useful information about the propensity of scale to deposit on solids.     

Introducing speckle noise maps for Laser Vibrometry

When coherent light scatters from a surface, which is rough on the scale of the wavelength of the light, a speckle pattern is produced. The Laser Vibrometer measures target vibration velocity in the direction of the incident laser beam and typically samples a region of a speckle pattern on its photodetector. Target motions can cause the speckle pattern to change on the photodetector surface, particularly when target motions are non-normal to the direction of the laser beam. This speckle motion modulates the Doppler signal and adds noise to the demodulated output signal. Periodic target motions can cause the speckle noise to become pseudo-random and produce harmonic peaks, with the same fundamental frequency as the genuine target vibrations, which can be indistinguishable from the genuine target vibrations. Typical speckle noise levels are generally considered to be low-level, but they have not so far been adequately quantified. This paper reports preliminary results quantifying speckle noise levels using controlled experimental configurations incorporating periodic in-plane and tilt target motions. Working with commercial Laser Vibrometers, various target surface finishes and treatments are considered and speckle noise maps are produced for each configuration. For a tilting surface, speckle noise has been quantified at approximately 1 μm s^?1/deg s^?1 while, for surfaces with in-plane motion, the sensitivity to speckle noise has been estimated pessimistically at 0.1% of the in-plane velocity. Ultimately, these speckle noise maps will form a valuable practical resource for the Laser Vibrometer user.     

Passivation of aluminum with alkyl phosphonic acids for biochip applications

Self-assembly of decylphosphonic acid (DPA) and octadecylphosphonic acid (ODPA) was studied on aluminum films using XPS, ToF-SIMS and surface wettability. Modified aluminum films were tested for passivation against silanization and subsequent oligonucleotide attachment. Passivation ratios of at least 450:1 compared to unprotected aluminum were obtained, as quantified by attachment of radio-labeled oligos.     

Accurate method for measuring the thermal coefficient of group birefringence of polarization-maintaining fibers

We present a method to accurately measure the group birefringence variation with temperature in high-birefringence polarization-maintaining (PM) fibers using a distributed polarization analyzer. By analyzing polarization cross-talk peaks purposely induced at both ends of a PM fiber, the temperature coefficient of group birefringence can be accurately obtained. We confirm the theoretical prediction that the group birefringence of PANDA and TIGER PM fibers decrease linearly with temperature from -40 °C to 80 °C, and find that the temperature coefficients are -5.93 × 10(-7) °C(-1) and -5.29 × 10(-7) °C(-1) for two types of PANDA fibers, and -5.36 × 10(-7) °C(-1) for a TIGER fiber.     

Application of phased array techniques to coarse grain components inspection

Ultrasonic inspection of cast stainless steel components from primary and auxiliary cooling circuits of French Nuclear Power Plant has to face with major difficulties due to the coarse grained structure of these materials. Attenuation losses and structural noise are encountered, which limits the performances of defect detection ability, mostly in terms of degraded signal-to-noise ratio and poor sensitivity. To overcome such problems, theoretical and experimental studies have been achieved at the French Atomic Energy Commission, with support from the French Institute for Radiological Protection and Nuclear Safety. Experimental studies have been performed over stainless steel specimen of known coarse structure (equiaxial grains and/or elongated grains), containing artificial reflectors (cylindrical holes and electro-eroded surface breaking notches). Those mock-ups have been inspected using contact probes of different array designs (linear or matrix splitting), and using pulse echo or dual-element techniques. Such arrays allow to control the ultrasonic beam so as to investigate different inspection angles and focusing depths. Experiments were carried out using oblique longitudinal waves, using delay laws computed by a specific model, taking account of acoustical and geometrical properties of the probes and the inspected component. In addition, specific reconstruction techniques have been investigated to enhance the signal-to-noise ratio as well as spatial resolution. These techniques are based on beam-forming summation and multi-angle inspections. Experimental results show that such techniques allow to reduce the speckle noise and to optimise the beam resolution. Those increased performances allow to detect and to size small planar defects located at the inner wall of a thick specimen, using corner and tip diffraction echoes.