Rugged distal tips for CO2 laser medicine

Low-loss and rugged distal tips for CO₂ laser have been proposed and fabricated based on a commercially available stainless steel (St) pipe. A method of smoothening the inner surface of the St pipe with a rough inner surface is put forward. Fabrication parameters, transmission properties, and mechanical strength of the cyclic olefin polymer-coated silver hollow St distal tip are experimentally discussed.     

利用模式的对称性研究光子晶体光纤的色散

由光子晶体光纤的对称性可以得到模式分布的对称性，根据模式的对称性选择适当的展开函数，可以使计算量大大减少。计算了六角结构光子晶体光纤的色散特性，得到了波长在1．55pm处色散为零时，光子晶体光纤的结构参量所满足的方程。     

Phase formation and control of morphology in sputtered Cu-In alloy layers

The dependence of structural properties and surface morphology of Cu-In alloy layers on the composition and sputtering deposition sequence were investigated by X-ray diffraction, scanning electron microscopy and energy-dispersive X-ray spectroscopy. The properties of the co-sputtered alloy layers changed abruptly around the composition boundary when the Cu/In ratio reached 1/2. This can be explained by the effective heat of formation (EHF) model, which has been used to predict the sequence of phase formation for metal diffusion couples. The use of a co-sputtered alloy layer with a high In concentration was not suitable for fabricating solar cells, because the film had a very rough morphology due to large In islands formed on the CuIn₂ phase. However, it was possible to minimize this phase by In sputtering followed by co-sputtering with a Cu/In ratio of 1 (Cu-In/In/Glass). This permitted the fabrication of a homogeneous Cu-In alloy layer, which was not possible through the simple co-sputtering.     

神光Ⅱ上柱形黑腔辐射驱动冲击波

利用神光Ⅱ的八路三倍频激光装置，驱动柱形黑腔产生的x 射线作辐射源驱动台阶铝样品产生冲击波，获得了清晰的冲击波图像，通过冲击波过台阶样 品的时间差获得冲击波速度和压力分别为31.2km/s和17.5×10⁵MPa.采用软x射线能谱 仪通过激光注入孔测量的辐射温度与采用冲击波法测量辐射温度的结果一致. 关键词： 冲击波 辐射驱动 辐射温度     

Bi12TiO20纳米粉体的制备及其光吸收特性研究

以钛酸四丁酯和硝酸铋为原料 ,利用化学溶液分解法制备了Bi12 TiO2 0 纳米多晶粉体 .采用XRD和TEM对其结构和形貌进行了表征 .结合热重 差热 (TG DTA)分析 ,探讨了Bi12 TiO2 0 晶相的形成机理 .通过UV Vis漫反射谱的测定 ,研究了Bi12 TiO2 0 纳米晶粉体的光吸收特性 .结果显示 ,从组成为化学计量比的前驱液中可以很容易制得纯Bi12 TiO2 0 纳米晶粉体 ,该Bi12 TiO2 0 纳米晶粉体呈现了在很宽的波长范围内 (5 6 0～ 385nm )对光的吸收的特性 .     

加热炉内板坯粘塑性下桡变形的研究

在加热妒内，由于高温及重力作用，板坯两端的悬臂将产生下桡变形。悬臂越长，下桡将越大，导致悬臂下桡部分与出口端墙相碰，影响出料而造成事故。本文对加热炉内板坯的下桡变形进行了分析计算。首先，建立了板坯的二维非稳态导热模型并用有限差分法计算了炉内板坯随时间的温度变化；然后建立了板坯悬臂粘塑性变形模型，用有限元法计算了高温条件下由重力引起的悬臂的下桡变形。由此理论模型计算出的板坯抽出温度与悬臂端下桡量与实测结果吻合良好，说明该理论模型及模型计算方法是正确的，可用于对装钢生产进行指导。     

改革物理实验课教学,提高实验课的教学质量

根据多年的物理实验教学经验，阐明了物理实验教学改革应重视的问题，并提出了几点改进措施。     

Quantum wire heterostructure for optoelectronic applications

Quantum wire (QWR) heterostructures suitable for optoelectronic applications should meet a number of requirements, including defect free interfaces, large subband separation, long carrier lifetime, efficient carrier capture. The structural and opticl properties of GaAs/AlGaAs and InGaAs/GaAs quantum wire (QWR) heterostructures grown by organometallic chemical vapor deposition on nonplanr substrates, which satisfy many of these criteria, are described. These crescent-shaped QWRs are formed in situ during epitaxial growth resulting in virtually defect free interfaces. Effective wire widths as small as 10nm have been achieved, corresponding to electron subband separations greater than K_BT at room temperature. The enhanced density of states at the QWR subbands manifests itself in higher optical absorption and emission as visualized in photoluminescence (PL), PL excitation, amplified spontaneous emission and lasing spectra of these structures. Effective carrier capture into the wires via connected quantum well regions, which is important for enhancing the otherwise extremely small capture cross section of these wires, has also been observed. Room temperature operation of GaAs/AlGaAs and strained InGaAs/GaAs QWR lasers with threshold currents as low as 0.6mA has been demonstrated.