MEASUREMENT OF ADHESION FORCES IN AIR WITH THE VIBRATION METHOD

The vibration method represents a practical method for the measurement of adhesion forces and adhesion force distributions. This method causes sinusoidally altemating stresses and yields detachment and contact forces between particles and substrate of the same order of magnitude. Alternating contact forces of the vibration method can cause an adhesion force intensification through flattening of asperities. The measuring principle of the vibration method and the analysis of experimental results are described in the article. Normal adhesion forces (pull-off forces) are measured using the vibration method and the colloidal probe technique. The results of both methods show good agreement for small particle sizes. The influence of the detachment force direction is shown by comparing tangential and normal adhesion forces measured using particle reentrainment in a turbulent air flow and the vibration method, respectively. The surface roughness of the substrate and the relative humidity are shown to significantly influence the measured adhesion forces. For the calculation of the adhesion forces, an approach by Rabinovich was combined with approximations of plastic micro asperity flattening. The Rabinovich approach accounts for roughness effects on the van der Waals force by incorporating the rms roughness of the interacting surfaces. rms-values of the particles and substrates were measured with atomic force microscopy at different scanning areas.     

在材料研制中的连续介质细观力学有限元建模现状评论（译文）

评述了机械载荷下材料力学行为有限元模拟的先进技术.分析 了考虑材料微观及细观结构情况下，对材料变形、损伤、断裂进行模 拟时各种方法的优缺点及发展前景.阐述了对材料行为模拟方法的发 展，包括基本的及先进的方法，如体胞方法、真实结构模拟、粘结区 模型等.分析了在先进新材料的开发中运用有限元方法的可能性     

Eine neue Theorie zur Rotationsumwandlung der n-Paraffine (Kinkentheorie)

Zusammenfassung Die Rotationsumwandlung der n-Paraffine wird als Übergang eines Paraffinkristalls mit 2gl-Kinken als Baufehler in einen Kinkblockkristall theoretisch behandelt. Die dabei mit zwei Methoden diskutierten Näherungen — für kurze und für sehr lange Ketten — liefern Aussagen über Umwandlungstemperatur, Umwandlungswärme und Volumensprung, die den experimentellen Werten entsprechen, die Kettenlängenabhängigkeit annähernd beschreiben und die Konzentrationsabhängigkeit der Umwandlungstemperatur sowie der Umwandlungswärme in Paraffinmischungen richtig wiedergeben.Vorgetragen auf der Jahrestagung der Deutschen Rheologen in Berlin-Dahlem vom 7.–10. Juni 1966.Herrn Prof.H. O. Kneser danken wir für die Förderung dieser Arbeit, der Deutschen Forschungsgemeinschaft für finanzielle Unterstützung.     

Frequency based preconditioning and smoothing for shape optimization

In this paper, we present a smoothing technique which can be understood as a Quasi-Newton method. The idea of this preconditioner is that it approximates the symbol of the inverse Hessian, which has smoothing behavior. This symbol is derived analytically for the Stokes equations and investigated numerically for a flow with a Reynolds number of 80. The resulting symbol is then approximated by differential operators, which will lead to a method similar to Sobolev Smoothing. (© 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim)     

Thermal fracture of a functionally graded/homogeneous bimaterial with system of cracks

The thermal fracture of a bimaterial consisting of a homogeneous material and a functionally graded material (FGM) with a system of internal cracks and an interface crack is investigated. The bimaterial is subjected to a heat flux. The thermal properties of FGM are assumed to be continues functions of the thickness coordinate, while the elastic properties are constants. The method of the solution is based on the singular integral equations. For a special case where the interface crack is much larger than the internal cracks in the FGM the asymptotic analytical solution of the problem is obtained as series in a small parameter (the ratio between sizes of the internal and interface crack) and the thermal stress intensity factors (TSIFs) are derived as functions of geometry of the problem and material characteristics. A parametric analysis of the effects of the location and orientation of the cracks and of the inhomogeneity parameter of FGM’s thermal conductivity on the TSIFs is performed. The results are applicable to such kinds FGMs as ceramic/ceramic FGMs, e.g., TiC/SiC, MoSi₂/Al₂O₃ and MoSi₂/SiC, and also some ceramic/metal FGMs.