Imaging intrinsic diffusion of bridge-bonded oxygen vacancies on TiO2(110)

We report the first measurements and calculations of the intrinsic mobility of bridge-bonded oxygen (BBO) vacancies on a rutile TiO2(110). The sequences of isothermal (340-420 K) scanning tunneling microscope images show that BBO vacancies migrate along BBO rows. The hopping rate increases exponentially with increasing temperature with an experimental activation energy of 1.15 eV. Density functional theory calculations are in very good agreement giving an energy barrier for hopping of 1.03 eV. Both theory and experiment indicate repulsive interactions between vacancies on a given BBO row.     

In situ synthesis of CdS/ZnS composite nanoparticles from ZIF-8 for visible light disposal of Cr(VI)

Journal of Sol-Gel Science and Technology - Zeolitic Imidazolate Framework (ZIF-8) micropolyhedra were employed as a raw material for the synthesis of fine cadmium sulfide/zinc sulfide (CdS/ZnS)...     

辐射接枝法制备膨化聚四氟乙烯杂化膜及其抗菌性表征

通过共辐射接枝的方法,将聚丙烯酸成功接枝到膨化聚四氟乙烯薄膜上. 采用NaBH₄还原吸附在接枝链上的银离子,在膜中原位负载银纳米粒子,制备了抗菌性ePTFE杂化膜. 杂化膜的SEM、XPS、XRD和TGA表征结果表明,负载的银纳米粒子粒径为几十纳米至100 nm. 而银纳米粒子的负载量可由聚丙烯酸的接枝率控制. 细菌平板计数法测试结果证明,所制备的杂化膜具有优异的抗菌性,对大肠杆菌的抗菌率高达100%.     

Excellent passivation of thin silicon wafers by HF‐free hydrogen plasma etching using an industrial ICPECVD tool

In this work, hydrogen plasma etching of surface oxides was successfully accomplished on thin (～100 µm) planar n‐type Czochralski silicon wafers prior to intrinsic hydrogenated amorphous silicon [a‐Si:H(i)] deposition for heterojunction solar cells, using an industrial inductively coupled plasma‐enhanced chemical vapour deposition (ICPECVD) platform. The plasma etching process is intended as a dry alternative to the conventional wet‐chemical hydrofluoric acid (HF) dip for solar cell processing. After symmetrical deposition of an a‐Si:H(i) passivation layer, high effective carrier lifetimes of up to 3.7 ms are obtained, which are equivalent to effective surface recombination velocities of 1.3 cm s^–1 and an implied open‐circuit voltage (V_oc) of 741 mV. The passivation quality is excellent and comparable to other high quality a‐Si:H(i) passivation. High‐resolution transmission electron microscopy shows evidence of plasma‐silicon interactions and a sub‐nanometre interfacial layer. Using electron energy‐loss spectroscopy, this layer is further investigated and confirmed to be hydrogenated suboxide layers. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Trapezoidal phase mask coronagraph

An angular trapezoidal phase mask used for a wideband coronagraph is proposed. The azimuthal phase of the mask is double-periodic and has both trapezoidal and constant parts in each period. This kind of continuous phase distribution can be employed to avoid the abrupt phase variation of the 6-level phase distribution we proposed previously. Numerical calculations show that this more practical phase mask can still keep its superior performance in terms of starlight elimination, small inner working angle, and good achromatism. It is of great importance that there is no singularity in this kind of mask except for a singularity at the center. This mask design is close to real manufacturing conditions, and the process technology is superior.     

Preparation and thermal properties of poly[acrylonitrile-co-(β-methylhydrogen itaconate)] used as carbon fiber precursor

In order to replace terpolymer with bipolymer, a bifunctional comonomer β-methylhydrogen itaconate (MHI) containing carboxyl group and ester group was synthesized to prepare poly[acrylonitrile-co-(β-methylhydrogen itaconate)] [P(AN-co-MHI)] bipolymers used as carbon fiber precursor for improving the stabilization and spinnability at the same time. The P(AN-co-MHI) bipolymers with different monomer feed ratios were characterized by elemental analysis, Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and differential scanning calorimetry (DSC). The results show that both the polymerization conversion and molecular mass of P(AN-co-MHI) reduce with the increasing MHI amounts in the feed due to the larger molecular volume of MHI than acrylonitrile (AN). The monomer reactivity ratios were calculated by Fineman–Ross and Kelen–Tüdõs methods, the results show good agreement and MHI possesses higher reactivity than AN. Two parameters $ E_{\text{s}} = A_{{1,629\,{\text{cm}}^{ - 1} }} /A_{{2,244\,{\text{cm}}^{ - 1} }} $ and $ SI = (I_{0} - I_{\text{S}} )/I_{0} $ were defined to evaluate the extent of stabilization, and the activation energy (E _a) of the cyclization was calculated by Kissinger method and Ozawa method. The FTIR, XRD, and DSC results show that P(AN-co-MHI) bipolymers exhibit significantly improved stabilization characteristics than PAN homopolymer, such as larger extent of stabilization, lower initiation temperature, and smaller E _a of cyclization, which is attributed to the ionic initiation by MHI comonomer and it is beneficial to preparing high-performance carbon fiber.     

Pyrolysis and combustion model of oil sands from non-isothermal thermogravimetric analysis data

Thermogravimetric (TG) data of oil sand obtained at Engineering Research Center of Oil Shale Comprehensive Utilization were studied to evaluate the kinetic parameters for Indonesian oil sand samples. Experiments were carried out at heating rates of 5, 15, and 25 °C min^?1 in nitrogen, 10, 20, and 50 °C min^?1 in oxygen atmosphere, respectively. The extent of char combustion was found out by relating TG data for pyrolysis and combustion with the ultimate analysis. Due to distinct behavior of oil shale during pyrolysis, TG curves were divided into three separate events: moisture release, devolatilization, and evolution of fixed carbon/char, where for each event, kinetic parameters, based on Arrhenius theory, were calculated. Coats–Redfern method, Flynn–Wall–Ozawa method, and distributed activation energy model method have been used to determine the activation energies of degradation. The methods are compared with regard to their characteristics and the ease of interpretation of the thermal kinetics. Activation energies of the samples were determined by three different methods and the results are discussed.     

Improvement of electrochemical performance for Li-rich spherical Li1.3[Ni0.35Mn0.65]O2+x modified by Al2O3

The Li-rich Li_1.3[Ni_0.35Mn_0.65]O_2+x microspheres are firstly prepared and subsequently transferred into the Al₂O₃-coated Li-rich Li_1.3[Ni_0.35Mn_0.65]O_2+x microspheres by a simple deposition method. The as-prepared samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge/discharge tests. The results reveal that the Al₂O₃-coated Li-rich Li_1.3[Ni_0.35Mn_0.65]O_2+x sample has a typical α-NaFeO₂ layered structure with the existence of Li₂MnO₃-type integrated component, and the Al₂O₃ layer is uniformly coated on the surface of the spherical Li-rich Li_1.3[Ni_0.35Mn_0.65]O_2+x particles with a thickness of about 4 nm. Importantly, the Al₂O₃-coated Li-rich sample exhibits obviously improved electrochemical performance compared with the pristine one, especially the 2 wt.% Al₂O₃-coated sample shows the best electrochemical properties, which delivers an initial discharge capacity of 228 mAh g^?1 at a rate of 0.1 C in the voltage of 2.0–4.6 V, and the first coulombic efficiency is up to 90 %. Furthermore, the 2 wt.% Al₂O₃-coated sample represents excellent cycling stability with capacity retention of 90.9 % at 0.33 C after 100 cycles, much higher than that of the pristine one (62.2 %). Particularly, herein, the typical inferior rate capability of Li-rich layered cathode is apparently improved, and the 2 wt.% Al₂O₃-coated sample also shows a high rate capability, which can deliver a capacity of 101 mAh g^?1 even at 10 C. Besides, the thin Al₂O₃ layer can reduce the charge transfer resistance and stabilize the surface structure of active material during cycling, which is responsible for the improvement of electrochemical performance of the Li-rich Li_1.3[Ni_0.35Mn_0.65]O_2+x .     

Nickel‐Catalyzed Site‐Selective Amidation of Unactivated C(sp3)H Bonds

Intramolecular dehydrogenative cyclization of aliphatic amides was achieved on unactivated sp³ carbon atoms by a nickel‐catalyzed C?H bond functionalization process with the assistance of a bidentate directing group. The reaction favors the C?H bonds of β‐methyl groups over the γ‐methyl or β‐methylene groups. Additionally, a predominant preference for the β‐methyl C?H bonds over the aromatic sp² C?H bonds was observed. Moreover, this process also allows for the effective functionalization of benzylic secondary sp³ C?H bonds.