SiOx纳米管的制备及其发光特性

以液态金属镓为媒介,利用热蒸发法合成大量非晶SiOx纳米管,这些纳米管管径均匀分布,平均约80 nm,长度大于10μm,且管内外径比例较小．分析发现,在实验过程中,熔入金属镓液滴中的硅元素和氧元素结合并从液滴的表面饱和析出,形成以镓为中心的非晶SiOx纳米管状结构．在室温中,利用260 nm的激发光源激发SiOx纳米管,发现在蓝光波段附近发出强而稳定的PL谱线,这可能与样品中的氧缺陷和空位有关．     

Soliton interaction under the influence of higher-order effects

In this paper, we present exact N-soliton solution by employing simple, straightforward Darboux transformation based on the Lax pair for Hirota equation, a higher-order nonlinear Schrödinger (HNLS) equation. As examples, one- and two-soliton solutions in explicit forms are given and their properties are also analyzed. A bound solution without interaction will be theoretically predicted if one can adjust frequency shift for each soliton appropriately. Further, we obtain the approximate eigenvalues by employing two-soliton solution and discuss analytically the interaction between neighboring solitons under the influence of the higher-order effects. It is shown that the combined effects of the higher-order effects can restrain the interaction between neighboring solitons to some extent. The results are proved by directly solving HNLS equation numerically.     

Combined effect of PMD and PDL on four-wave-mixing-induced crosstalk in WDM system

We derive an explicit autocorrelation function (ACF) formula of state of polarization for a fiber transmission system with polarization mode dispersion (PMD) and polarization dependent loss (PDL), which is found to agree well with Monte Carlo simulation. Then we use the new ACF to investigate the combined effect of PMD and PDL on the polarization multiplexed scheme. We find the performance of the polarization multiplexed scheme can be deteriorated more severely than the case without PDL.     

Reciprocating sliding wear behavior of laser-clad small amplitude Mo2Ni3Si/NiSi metal silicide composite coatings

Mo₂Ni₃Si/NiSi metal silicide composite coatings with a fine microstructure consisting of Mo₂Ni₃Si primary dendrites and the interdendritic Mo₂Ni₃Si/NiSi eutectics were fabricated on austenitic stainless steel AISI 321 by laser cladding process. Small amplitude reciprocating sliding wear resistance of the coatings is evaluated as functions of normal load and slip amplitude and the wear mechanisms were discussed based on worn surface morphology observations. Results showed that the Mo₂Ni₃Si/NiSi coatings have excellent small amplitude reciprocating sliding wear resistance.     

Stabilized hybrid finite element methods based on the combination of saddle point principles of elasticity problems

How, in a discretized model, to utilize the duality and complementarity of two saddle point variational principles is considered in the paper. A homology family of optimality conditions, different from the conventional saddle point conditions of the domain-decomposed Hellinger-Reissner principle, is derived to enhance stability of hybrid finite element schemes. Based on this, a stabilized hybrid method is presented by associating element-interior displacement with an element-boundary one in a nonconforming manner. In addition, energy compatibility of strain-enriched displacements with respect to stress terms is introduced to circumvent Poisson-locking.

     

Resistivity－temperature characteristics of sol gel YBa2Cu3Oy samples synthesized in flowing oxygen atmosphere

The relationship of resistivity versus synthesizing temperature of sol gel YBa_2Cu_3O_y samples was studied when prepared under flowing oxygen conditions. A set of high-temperature ρ－T curves was obtained for the whole process. After the sample finished the test measuring, its resistivity was ρ_{300}=9.83×10^{-3 }Ω·cm at room temperature. The ρ－T curve also showed that the orthorhombic－tetragonal phase transformation of sol-gel YBa_2Cu_3O_y sample occurred at 581℃ for the sample in the rising temperature process, but at 613℃ in the cooling process, lower than that of the samples made by using the conventional powder metallurgy methods.     

Self‐assembly of amphiphilic tris(2,2′‐bipyridine)ruthenium‐cored star‐shaped polymers

Amphiphilic tris(2,2′‐bipyridine)ruthenium‐cored star‐shaped polymers consisting of one polystyrene block and two poly(N‐isopropylacrylamide) blocks were prepared by the “arm‐first” method in which RAFT polymerization and nonconvalent ligand–metal complexation were employed. The prepared amphiphilic star‐shaped metallopolymers are able to form micelles in water. The size and distribution of the micelles were studied by dynamic light scattering and transmission electron microscopy techniques. Preliminary studies indicate that the polymer concentration and the hydrophilic poly(N‐isopropylacrylamide) block length can affect the morphologies of the formed metal‐interfaced core–shell micelles in water. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4204–4210, 2007     

Low Cost, High Efficiency, Gain Flattened L Band EDFA Using FBGs as C Band Seed Generators

A low cost, coolerless 980nm diode pumped, gain flattened L band EDFA with fast transient control, high pump efficiency and gain clamping effect was realized by using FBGs as C band seed generators.     

Behavior of cellulose in NaOH/Urea aqueous solution characterized by light scattering and viscometry

Cellulose was dissolved in 6 wt % NaOH/4 wt % urea aqueous solution, which was proven by a ¹³C NMR spectrum to be a direct solvent of cellulose rather than a derivative aqueous solution system. Dilute solution behavior of cellulose in a NaOH/urea aqueous solution system was examined by laser light scattering and viscometry. The Mark–Houwink equation for cellulose in 6 wt % NaOH/4 wt % urea aqueous solution at 25 °C was [η] = 2.45 × 10^?2 weight‐average molecular weight (M_w)^0.815 (mL g^?1) in the M_w region from 3.2 × 10⁴ to 12.9 × 10⁴. The persistence length (q), molar mass per unit contour length (M_L), and characteristic ratio (C_∞) of cellulose in the dilute solution were 6.0 nm, 350 nm^?1, and 20.9, respectively, which agreed with the Yamakawa–Fujii theory of the wormlike chain. The results indicated that the cellulose molecules exist as semiflexible chains in the aqueous solution and were more extended than in cadoxen. This work provided a novel, simple, and nonpollution solvent system that can be used to investigate the dilute solution properties and molecular weight of cellulose. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 347–353, 2004     

0.8W/80K直线驱动斯特林制冷机的研制

介绍了一种 0 .8W/ 80 K分置式斯特林制冷机。该制冷机采用当前国外先进的直线电机驱动 ,双活塞对称布置结构。该制冷机已通过军品所要求的环境试验 ,输入功率小于 4 0 W(DC)情况下 ,其 +6 0℃高温环境下制冷量≥ 0 .5 W/ 80 K ,带载 0 .5 W工况下 MTTF已突破 2 0 0 0小时。文中主要论述了其工作原理、结构特点、试验情况。