二安替比林基-4-羟基苯基甲烷及其与铬(Ⅵ)显色反应的研究

合成了二安替比林基-4-羟基苯基甲烷(DApHM),研究了它与铬(Ⅵ)的显色反应,建立了两个测定铬(Ⅵ)的新体系.在Mn(Ⅱ)和磷酸存在下,DApHM与 Cr(Ⅵ)反应生成橙红色产物,λ_max为435nm.CTMAB和Tween-80对该体系有明显增敏效果,其中CTMAB-DApHM-Cr(Ⅵ)体系ε为1.0 ×10~6;Tween-80-DApHM-Cr(Ⅵ)体系ε为6.9×10~5.Cr(Ⅵ)量在0.1～0.7μg/25mL间符合比尔定律.用于电镀废液和自来水中Cr(Ⅵ)的测定,结果满意.     

二阶导数差示脉冲极谱法用于醋酸氟氢可的松的定量研究

用二阶导数差示脉冲极谱法对醋酸氟氢可的松进行了定量分析。在０．００１ｍｏｌ／Ｌ硫酸＋乙醇＋水（１＋２５＋２４）的底液中，醋酸氟氢可的松于－０．３４０Ｖ（ｖｓＡｇ／ＡｇＣｌ）处出现一良好的二阶导数差示脉冲极谱峰，在５～１４０μｇ／ｍＬ范围内，醋酸氟氢可的松的浓度与其二阶导数差示脉冲极谱峰幅值呈线性关系，检测限为０．４ｎｇ／ｍＬ。本法操作简便、快速、灵敏、结果准确。     

锂离子电池用多孔硅/石墨/碳复合负极材料的研究

在两步高能球磨和酸蚀条件下制得了多孔硅/石墨复合材料，并对其进行碳包覆制成多孔硅/石墨/碳复合材料。通过TEM，SEM等测试手段研究了多孔硅材料的结构。作为锂离子电池负极材料，电化学测试结果表明多孔硅/石墨/碳复合材料相比纳米硅/石墨/碳复合材料有更好的循环稳定性。同时，改变复合体配比、热解碳前驱物、粘结剂种类和用量也会对材料的电化学性能产生较大的影响。其中使用质量分数为10％的LA132粘结剂的电极200次循环以后充电容量保持在649.9 mAh·g^-1，几乎没有衰减。良好的电化学性能主要归因于主活性体-多孔硅颗粒中的纳米孔隙很好地抑制了嵌锂过程中自身的体积膨胀，而且亚微米石墨颗粒和碳的复合也减轻了电极材料的体积效应并改善了其导电性。     

Microcalorimetric investigation of the growth of the <Emphasis Type="Italic">Escherichia coli</Emphasis> DH5α in different antibiotics

The effects of Amoxicillin Sodium and Cefuroxime Sodium on the growth of E. coli DH5α were investigated by microcalorimetry. The metabolic power-time curves of E. coli DH5α growth were determined by using a TAM air isothermal microcalorimeter at 37°C. By evaluation of the obtained parameters, such as growth rate constants (k), inhibitory ratio (I), the maximum heat power (P _m) and the time of the maximum heat power (t _m), one found that the inhibitory activity of Amoxicillin Sodium vs. E. coli DH5α is enhanced with the increasing of the Amoxicillin Sodium concentration, and the Cefuroxime Sodium has a stimulatory effect on the E. coli DH5α growth when the concentration is about 1 μg mL⁻¹. The IC₅₀ for the Amoxicillin Sodium and the Cefuroxime Sodium are 1.6 and 2.0 μg mL⁻¹, respectively, it implicates that the E. coli DH5α is more sensitive to Amoxicillin Sodium than Cefuroxime Sodium.     

Flow injection chemiluminescence determination of nitrofurazone in pharmaceutical preparations and biological fluids based on oxidation by singlet oxygen generated in N-bromosuccinimide-hydrogen peroxide reaction

A simple flow injection chemiluminescence (FI-CL) method was proposed for the determination of nitrofurazone. Strong CL signal was generated during the reaction of nitrofurazone with H₂O₂ and N-bromosuccinimide (NBS) in alkaline condition. The CL signal was proportional to the nitrofurazone concentration in the range 1.0 × 10⁻⁷ to 1.0 × 10⁻⁵ g mL⁻¹. The detection limit was 2 × 10⁻⁸ g mL⁻¹ nitrofurazone and the relative standard deviation was less than 4% (6.0 × 10⁻⁶ g mL⁻¹ nitrofurazone, n = 11). The proposed method was successfully applied to the determination of nitrofurazone in compound furacillin nasal drops, human plasma and urine samples. The CL reaction mechanism was also discussed briefly. Singlet oxygen generated in the reaction between H₂O₂ and NBS was suggested to be participated in the CL reaction.     

Preparation and characterization of sodium carboxymethylcellulose/poly(N-isopropylacrylamide)/clay semi-IPN nanocomposite hydrogels

A new kind of pH-/temperature-responsive semi-interpenetrating polymer network hydrogels based on linear sodium carboxymethylcellulose (CMC) and poly(N-isopropylacrylamide) (PNIPA) cross-linked by inorganic clay (CMC/PNIPA/Clay hydrogel) was prepared. The temperature- and pH-responsive behaviors, the mechanical properties of these hydrogels were investigated. The CMC/PNIPA/Clay hydrogels exhibited a volume phase transition temperature around 32 °C with no significant deviation from the conventional PNIPA hydrogels. The swelling ratio of the CMC/PNIPA/Clay hydrogels gradually decreased with increasing the contents of clay. The influence of pH value on swelling behaviors showed that there is a maximum swelling ratio at pH 5.9. Moreover, the CMC/PNIPA/Clay hydrogels exhibited excellent mechanical properties with high tensile stress and elongation at break in excess of 1200%.     

Highly Efficient One-Pot Synthesis of 2-Arylmethyl N-Substituted Anilines via Yb（OTf）3 Catalyzed Three-Component Reaction

An efficient method has been developed for one-pot three-component coupling reactions of various aldehydes, 1-cyclohexen-2-one, and primary or secondary amines in the presence of a catalytic amount of Yb（OTf）3 under mild conditions to afford the corresponding 2-arylmethyl N-substituted anilines in good yields. In addition, the catalyst was easily recovered and could be reused for at least four cycles without any loss of activity.     

Crystallization and melting behaviors of polystyrene-b-poly(ethylene-co-butene) block copolymers

Non-isothermal and isothermal crystallization behaviors of polystyrene-b-poly(ethylene-co-butene) (PSt-b-PEB) block copolymers with different compositions and chain lengths were investigated by differential scanning calorimetry (DSC). The results show that crystallization of PEB block is strongly dependent on the composition. Crystallization temperature (T_c), melting temperature (T_m) and fusion enthalpy (ΔH_f) increase rapidly with PEB volume fraction (V_E) for block copolymers with V_E below 50%, but there is little change when PEB block becomes the major component. Glass transition temperature (T_g) of the PSt block and order-disorder transition temperature (T_ODT) of block copolymers also have a weak effect. The isothermal crystallization kinetics results show that Avrami exponent (n) was strongly dependent on the composition and crystallization temperature. For the block copolymers with V_E below 38.7 vol%, the values of n vary between 0.9 and 1.3, indicating that crystallization is confined. For the PSt-b-PEB block copolymers with V_E higher than 50%, fractionated crystallization behavior is usually observed. A two-step isothermal crystallization procedure is applied to these block copolymers. It is found that breakout crystallization occurs at higher T_c, but confined at lower T_c. Two overlapped melting peaks are observed for the block copolymers with fractionated crystallization behavior after two-step crystallization, and only the higher melting peak corresponding to breakout crystallization can be used to derive equilibrium melting temperature.     

Inorganic speciation of As(III, V), Se(IV, VI) and Sb(III, V) in natural water with GF-AAS using solid phase extraction technology

The paper presents a procedure for the multi-element inorganic speciation of As(III, V), Se(IV, VI) and Sb(III, V) in natural water with GF-AAS using solid phase extraction technology. Total As(III, V), Se(IV, VI) and Sb(III, V) were determined according to the following procedure: titanium dioxide (TiO₂) was used to adsorb inorganic species of As, Se and Sb in sample solution; after filtration, the solid phase was prepared to be slurry for determination. For As(III), Se(IV) and Sb(III), their inorganic species were coprecipitated with Pb-PDC, dissolved in dilute nitric acid, and then determined. The concentrations of As(V), Se(VI) and Sb(V) can be calculated by the difference of the concentrations obtained by the above determinations. For the determination of As(III), Se(IV) and Sb(III), palladium was chosen as a modifier and pyrolysis temperature was 800 °C. Optimum conditions for the coprecipitation were listed for 100 ml of sample solution: pH 3.0, 15 min of stirring time, 40.0 μg l⁻¹ Pb(NO₃)₂ and 150.0 μg l⁻¹ APDC. The proposed method was applied to the determination of trace amounts of As(III, V), Se(IV, VI) and Sb(III, V) in river water and seawater.