The orientation-selective growth of LaNiO3 films on Si(100) by pulsed laser deposition using a MgO buffer

Highly (100)-oriented, (110)-oriented and polycrystalline LaNiO₃ (LNO) films were successfully prepared on Si(100) using an oriented MgO film as a buffer. It was somewhat surprising to find that that the orientation relation between the LNO film and the corresponding MgO buffer was: LNO(100)\MgO(110), LNO(110)\MgO(111) and LNO(polycrystalline)\MgO(100). The crystalline quality of the LNO films was shown to be sensitive to the preparation conditions of the MgO buffer. The film surface was very smooth, without micrometer-sized droplets being observed. All LNO films were of metallic conductivity, with a room-temperature resistivities of approximately 250, 280 and 420 μΩ cm for the (110)-oriented, (100)-oriented and polycrystalline LNO, respectively. Received: 2 April 2001 / Accepted: 23 October 2001 / Published online: 3 June 2002     

Active long pulse shaping technique of pulsed CO2 laser using multi-pulse discharge control

We describe the pulse forming of pulsed CO₂ laser using multi-pulse superposition technique. Various pulse shapes, high duty cycle pulse forming network (PFN) are constructed by time sequence. This study shows a technology that makes it possible to make various long pulse shapes by activating SCRs of three PFN modules consecutively at a desirable delay time with the aid of a PIC one-chip microprocessor. The power supply for this experiment consists of three PFN modules. Each PFN module uses a capacitor, a pulse forming inductor, a SCR, a high voltage pulse transformer, and a bridge rectifier on each transformer secondary. The PFN modules operate at low voltage by driving the primary of HV pulse transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence.We investigated various long pulse shapes as different trigger time intervals of SCRs among three PFN modules. As a result, we could obtain laser beam with various pulse shapes and durations from about 250 to 1000 μs.     

Experimental observation of quantum corrections to electrical resistivity in nanocrystalline soft magnetic alloys

X-ray diffraction patterns of nanocrystalline Fe-Cu-Nb-Si-B (FINEMET) alloys reveal that bcc α-Fe/α-FeSi crystallites with the average grain size of 20(5) nm are dispersed in amorphous matrix. Enhanced electron—electron interaction (EEI) and quantum interference (QI) effects as well as electron-magnon (and/or electron-spin fluctuation) scattering turn out to be the main mechanisms that govern the temperature dependence of resistivity. Of all the inelastic scattering processes, inelastic electron-phonon scattering is the most effective mechanism to destroy phase coherence of electron wave functions. The diffusion constant, density of states at the Fermi level and the inelastic scattering time have been estimated, for the first time, for the alloys in question Article presented at the International Symposium on Advances in Superconductivity and Magnetism: Materials, Mechanisms and Devices, ASMM2D-2001, 25–28 September 2001, Mangalore, India.     

On additives, morphological evolution and dielectric breakdown in low density polyethylene

A series of low density polyethylene systems has been studied with respect to structural evolution and short-term dielectric breakdown behaviour. All materials were based upon a single polymer, that is commonly used in high voltage applications, but with different additives. In all three of these systems, multiple melting transitions were observed, as a result of molecular fractionation effects during crystallization. In the virgin polymer, a space-filling banded spherulitic morphology was found to develop at low temperatures (102 °C and below) whereas, at higher temperatures, only a few isolated axialites were observed. Inclusion of the antioxidant resulted in greatly increased nucleation densities, such that, at low temperatures, no evidence of spherulitic organisation remained. At higher temperatures, sheaf-like lamellar aggregates developed, which were much smaller and much more numerous than in the case of the virgin polymer. Further addition of dicumyl peroxide (DCP) resulted in the rapid formation of a crosslinked network at 200 °C. Some crosslinking also occurred at 150 °C, but over a much longer timescale. Where extensive crosslinking occurred prior to crystallization, the resulting gel inhibited structural development, such that only a few small, isolated sheaves were able to form at 102 °C. In view of the principal application area of this material, the breakdown strength of each of the above systems was then measured and the whole data set was analysed statistically. When structural factors were considered alongside the statistics, no clear trends emerged to indicate that either the compositional or morphological variations were reflected in the short-term electrical failure processes.     

Effects of B′-site transition metal on the properties of double perovskites Sr2FeMO6 (M=Mo, W): B′ 4d-5d system

The crystal structure, magnetic and magnetotransport properties of the variation of B′-site transition metal in Sr₂FeMO₆ (M=Mo, W) with double perovskites structure have been investigated systematically. Measurements of magnetization vs. temperature at H=5 T show that Sr₂FeMoO₆ is a ferromagnet and Sr₂FeWO₆ is an antiferromagnet with T_N∼35 K. Additionally, the large magnetoresistance ratio (MR) of ∼22% (H=3 T) at room temperature (RT) was observed in the Sr₂FeWO₆ compound. However, the Sr₂FeMoO₆ compound did not show any significant MR even at high fields and RT (MR∼1%; H=3 T and 300 K). The implications of these findings are supported by band structure calculations to explain the interaction between the 4d(Mo) and 5d(W) orbitals of transition metal ions and oxygen ions.     

Efficient microwave induced direct α-halogenation of carbonyl compounds

A novel and direct method for the synthesis of α-halocarbonyl compounds using sequential treatment of carbonyl compounds with [hydroxy(tosyloxy)iodo]benzene followed by magnesium halides under solvent-free microwave irradiation conditions is described.     

Effects of sodium salicylate on the febrile response and increased levels of cyclic AMP in cerebrospinal fluid during endogenous pyrogen-induced fever in rabbits

To further evaluate the causality between endogenous pyrogen (EP)-induced fever and cyclic adenosine-3',5'-monophosphate (cyclic AMP) level, the effects of sodium salicylate (SS) on the febrile response and increased levels of cyclic AMP in both cerebrospinal fluid (c.s.f.) and plasma during EP-induced fever in rabbits were observed. The results suggest that cyclic AMP is probably involved in the central mediation of EP-induced fever and that increased concentration of cyclic AMP in c.s.f. associated with EP-induced fever is not the result of temperature elevation but appears to be caused by the increased synthesis in the central nervous system. In addition it is confirmed that blood is impossibly a contributory source of increased cyclic AMP in c.s.f. during EP fever, and that SS may act subsequent to the increase in cyclic AMP.     

Structure and superconductivity in FexCu1−xBa2YCu2O7+y superconductors synthesized by high pressure

Comprehensive studies of X-ray diffraction, oxygen content, superconductivity and Mössbauer effect have been made on Fe_xCu_1−xBa₂YCu₂O_7+y superconductors (0.00≤x≤0.70) synthesized by ambient (AM) and high pressure (HP). Results indicate that all the HP-samples have tetragonal structure, smaller lattice parameter c and unit-cell volume than the AM-samples. The studies of oxygen content, and Mössbauer spectroscopy indicate that the HP-samples have higher oxygen content, carrier concentration and average valence of Fe than the AM-samples. Moreover, for the HP-samples more Fe atoms located in CuO_x chains have fivefold-oxygen coordination. These are important reasons for the enhancement of T_c in the HP-samples.