On the Possibility of Replacing Standard Chromium-Plating Electrolytes with Sulfate-Oxalate Solutions of Cr(III)

A method for preparing sulfate-oxalate chromium-plating solutions by reducing Cr(VI) from industrial chromium-plating electrolytes to Cr(III) with a Na₂SO₃ solution is proposed.     

Numerical approximation of generalized Newtonian fluids using Powell–Sabin–Heindl elements: I. theoretical estimates

In this paper we consider the numerical approximation of steady and unsteady generalized Newtonian fluid flows using divergence free finite elements generated by the Powell–Sabin–Heindl elements. We derive a priori and a posteriori finite element error estimates and prove convergence of the method of successive approximations for the steady flow case. A priori error estimates of unsteady flows are also considered. These results provide a theoretical foundation and supporting numerical studies are to be provided in Part II. Copyright © 2003 John Wiley & Sons, Ltd.     

System Identification Models of the Equivalent Permittivity for Rain Medium

The dielectric constant for rain medium is investigated by utilizing the system identification method. The rain rate model and frequency model of permittivity in millimeter waves band for rain medium are presented. The results obtained with models are in very good agreement with references in calculating the attenuation of electromagnetic waves induced by rain, which Shows that the obtained models are valid and practicable. The cross-polar discrimination gotten with rain rate model is in agreement with references.     

Evidences of phase separation in moisture‐cured poly(urethane urea)s by means of temperature modulated differential scanning calorimetry

The degree of phase separation in several moisture‐cured poly(urethane urea)s (PUUs) was studied by FTIR spectroscopy, wide angle X‐ray diffraction (WAXD), and temperature‐modulated differential scanning calorimetry (TMDSC). This latter technique was shown to be particularly useful in analysing the degree of phase separation in PUU polymers. Both phase mixing and phase segregation coexisted in the PUUs and the degree of phase separation increased as the urea hard segment (HS) content in the PUU increased. The maximum solubility of urea HSs into the polyol soft segments (SSs) was achieved for 50 wt % urea HS content in diol‐based PUUs, whereas for triol‐based PUUs the highest solubility between HS and SS was reached for lower urea HS amount. Finally, the higher the urea HS content the higher the extent of phase separation in the PUU. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3034–3045, 2007     

Polarization dynamics of intracavity frequency-doubled Nd:YAG laser

Experimental study of low-frequency dynamics of an intracavity frequency-doubled Nd:YAG laser demonstrates the influence of the interaction of orthogonally polarized modes, participating in frequency doubling (type II phase matching), on the stability of the laser output. At a sufficiently low pump rate and low conversion efficiency, the laser shows stable operation with a low noise level at the frequencies of relaxation oscillations. At a high pump power and/or a high conversion efficiency, the laser emission becomes unstable as a result of Hopf bifurcation at the frequencies of relaxation oscillations that are responsible for the anti-phase polarization dynamics of the laser.     

What Oxidation State of Iron Determines the Amethyst Colour?

A colourless quartz crystal doped with ⁵⁷Fe³⁺ was obtained by hydrothermal synthesis in an NH₄F solution. The crystal was transformed into violet amethyst by gamma-irradiation. The change in colour was accompanied by changes in the Mössbauer spectrum that can be interpreted as the conversion of trivalent iron into the tetravalent state: Fe³⁺→Fe⁴⁺.

     

The mechanism of emission in the red photoluminescence band of porous silicon

Porous silicon (PS) exhibits several photoluminescence (PL) bands, whose spectral position and intensity depend strongly on the actual conditions of preparation of PS, its treatment, and subsequent use. The PS PL band peaking at about 1.8 eV and usually assigned to the intrinsic emission of silicon nanocrystals was studied. It was shown that the temperature-induced variation of the PL kinetics in the 80 to 300-K interval follows a complex pattern and depends noticeably on the actual point on the band profile. The temperature behavior of PL decay in the 1.8-eV band is determined by the electron-hole recombination rate within a nanocrystal and the cascade carrier transitions from small to large nanocrystals, with an attendant decrease in energy.     

A fast method to measure the thickness of removed layer from etching of SSNTD based on EDXRF

Solid state nuclear track detectors are commonly used for measurements of concentrations of radon gas and/or radon progeny. All these measurements depend critically on the thickness of the removed layer during etching. However, the thickness of removed layer calculated using the etching period does not necessarily provide a sufficiently accurate measure of the thickness. For example, the bulk etch rate depends on the strength of stirring during etching for the LR 115 detector. We propose here to measure the thickness of the removed layer by using energy-dispersive X-ray fluorescence spectrometry. In the present work, a reference silver nitrate pellet is placed beneath the LR 115 detector, and the fluorescence X-ray intensity for silver is then measured. We have found a linear relationship between the X-ray intensity and the thickness of the removed layer for LR 115 detector. This provides a fast method to measure the thickness of removed layer from etching of LR 115 detector. However, this method was found to be inapplicable for the CR-39 detector. Therefore, alternative methods have yet to be explored for the CR-39 detector.     

Effect of short glass fiber on structure and viscoelastic behavior of olefinic polymers synthesized with metallocene catalyst

Several composites were prepared on the basis of an ethylene homopolymer and different copolymers of ethylene and 1‐hexene, synthesized with a metallocene catalyst, as matrices and a content of a 5 wt % of short glass fiber. The effect of the fiber incorporation on the structure and mechanical and viscoelastic behaviors was analyzed for the different samples. The glass fibers induced a slightly higher crystallinity, and the crystallite morphology significantly changed (long spacings and crystal orientation). The incorporation of fibers did not reinforce the different matrices under study at this low content; consequently, the mechanical parameters, such as Young's modulus, yielding stress, and microhardness, were lower in the composites as compared with those values found in the neat polyolefins. The location and apparent activation energies of distinct relaxation processes are also discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1244–1255, 2003