Conformationally resolved structures of jet-cooled acetaminophen by UV-UV hole-burning spectroscopy

The conformational structures of jet-cooled acetaminophen were investigated in the gas phase by resonant 2-photon ionization and UV-UV hole-burning spectroscopy. In contrast to the results from a previous study, two nearly isoenergetic conformers were distinctly found in a supersonic molecular beam expansion and positively identified as the cis and trans isomers of acetaminophen by UV-UV hole-burning spectroscopy. The 0-0 bands of the cis and trans isomers were found at 33518.7 and 33485.6 cm(-1), respectively. The vibronic bands of the two isomers are close-lying and/or partially overlapping due to the small energy difference (33 cm(-1)) between the two 0-0 bands. As a consequence, the recorded resonant 2-photon ionization spectrum is highly congested in the low excitation energy region, which develops continuously into a featureless, broadened spectrum in the high energy region.     

Crystallinity and morphology dependent luminescence of Li-doped Y2−xGdxO3:Eu thin film phosphors

The influence of lithium doping on the crystallization, the surface morphology, and the luminescent properties of pulsed laser deposited Y_2−xGd_xO₃:Eu³⁺ thin film phosphors was investigated. The crystallinity, the surface morphology, and the photoluminescence (PL) of films depended highly on the Li-doping and the Gd content. The relationship between the crystalline and morphological structures and the luminescent properties was studied, and Li⁺ doping was found to effectively enhance not only the crystallinity but also the luminescent brightness of Y_2−xGd_xO₃:Eu³⁺ thin films. In particular, the incorporation of Li and Gd into the Y₂O₃ lattice could induce remarkable increase in the PL. The highest emission intensity was observed Li-doped Y_1.35Gd_0.6O₃:Eu³⁺ thin films whose brightness was increased by a factor of 4.6 in comparison with that of Li-doped Y₂O₃:Eu³⁺ thin films.     

Design of 40 GHz-Band Iris-Type Waveguide Bandpass Filter

In this paper, a design method of an iris-coupled waveguide bandpass filter having 0.1 dB passband ripple and 3.5% ripple bandwidth at the center frequency of 41 GHz is described. Mode matching method is used to analyze H-plane discontinuity of waveguide and an equivalent circuit of the thick inductive obstacle is obtained from the results of the analysis. Simulation and experimental results show the validity of waveguide bandpass filter design method using mode matching method.     

Polymerization of propylene catalyzed over highly active and stereospecific catalysts synthesized with Mg(OEt)2/benzoyl chloride/TiCl4

A series of monoester catalysts has been studied, each catalyst prepared by the reaction of magnesium diethoxide with benzoyl chloride [BzCOCl, to produce ethyl benzoate (EB) in situ] in the presence of excess titanium tetrachloride. Solid product and catalysts obtained by subsequent treatments with titanium tetrachloride were characterized by elemental analysis, IR spectroscopy, x-ray diffraction, BET measurement, and thermal gravimetric analysis. The catalysts yielded very high activity (above 20 kg polymer/g Ti h atm) for the polymerization of propylene in slurry reactions. From the results of polymerization as well as catalyst characterization, the effects of internal and external Lewis bases on the isospecificity and stability of catalysts are discussed in detail. © 1992 John Wiley & Sons, Inc.     

Effect of Pr-Ca substitution on the transport and magnetic behavior of LaMnO3 perovskite

The effect of simultaneous substitution of a fluctuating cation and a divalent cation in LaMnO₃ perovskite modifies the properties of the material to exhibit large valence colossal magnetoresistance (CMR) effect. A good example of these properties is (La_1−2x Pr _x Ca _x )MnO₃ (LPCMO) type CMR material. In this communication it is reported that, with the increase in x (for x=0.1, 0.15, 0.2), the T _c varies between 100 and 120 K with improvisation in metal-insulator transition. Interestingly, resistance increases with x from few hundred ohms to few kilo ohms with corresponding decrease in the unit cell volume. The results of the studies using X-ray diffraction (XRD), electrical resistivity, magnetoresistance and ac susceptibility measurements on LPCMO samples for understanding the structural, transport and magnetic properties are discussed in detail.     

Superhydrophobic CFx coating via in-line atmospheric RF plasma of He-CF4-H2

Stable superhydrophobic coatings on various substrates are attained with an in-line atmospheric rf plasma process using CF4, H2, and He. The coating layer is composed of CFx nanoparticulates and has an average roughness of approximately 10 nm. This roughness is much smaller than other surfaces reported for superhydrophobicity in the literature. The superhydrophobic coatings are produced on both metallic and insulating substrates without any need of separate microroughening or vacuum lines.     

Dependence of the closed-shell repulsive interaction on the overlap of the electron densities

The relationship between the closed-shell repulsive interactions and overlap of the electron densities is investigated. It is found that the repulsive interactions vary in almost direct proportion to the absolute size of the density overlaps.     

Active control of the depletion boundary layers in microfluidic electrochemical reactors

In this paper, we describe three methods to improve the performance of pressure-driven laminar flow-based microreactors by manipulating reaction-depletion boundary layers to overcome mass transfer limitations at reactive surfaces on the walls, such as electrodes. The transport rate of the reactants to the reactive surfaces is enhanced by (i) removing the depleted zone through multiple periodically-placed outlets; (ii) adding fresh reactants through multiple periodically-placed inlets along the reactive surface; or (iii) producing a spiraling, transverse flow through the integration of herringbone ridges along the channel walls. For approaches (i) and (ii), the network of microfluidic channels needs to be designed such that under the operating conditions used the right amount of boundary layer at each outlet or inlet is removed or replenished, respectively. Here, we report a set of design rules, derived with the help of a fluidic resistance circuit model, to aid in the design of appropriate microfluidic networks. Also, the actual enhancement of the performance of the electrochemical microreactor, i.e. chemical conversion efficiency, using multiple inlets, multiple outlets, or herringbone ridges is reported.