Large-volume injection electrothermal AAS combined with tungsten-treated pyrolytic graphite furnace: determination of cadmium in tap, snow and river water samples with phosphate modifier.

A large-volume (100 microl) injection-ETAAS with W-treated PG furnace combined with a phosphate modifier was applied to the determination of unpolluted levels of Cd in tap, snow and river-water samples. The limit of detection of 1.1 ng l(-1) was observed for a 4 w/v% NH4H2PO4 modifer. Matrix interference studies were tested for major ion species well found in fresh water. The direct determination of Cd in certified river water (12 +/- 2 ng l(-1)) was carried out and the observed value was in agreement with the certified one. The good recoveries of Cd added to real environmental water samples were also observed. This method was applied to the determination of Cd in unpolluted environmental water samples.     

Improved detectability with a polymer-based trapping device in rapid HPLC analysis for ultra-low levels of bisphenol A (BPA) in environmental samples.

A new high-performance liquid chromatography (HPLC) method has been developed to detect ultra-low concentrations of bisphenol-A (BPA) (below 1 ng/L (ppt)) using column switching electrochemical detection (ECD). The results were superior to those obtained from manual pretreatment procedure with membrane stationary phase. BPA is inherently ubiquitous in the environment, including tools and solvents used for its analysis; to obtain meaningful results, therefore, the concentration of the overall BPA contamination must be below the detection limit for BPA using the analytical system. Therefore, purified water for preparing the standard BPA solution must be filtered with a hydrophobic membrane to suppress BPA background levels of contamination. In addition, we investigated methods for effectively preserving environmental water containing BPA. The addition of a small amount of ethylenediaminetetraacetic acid (EDTA) provided good recovery even after overnight storage. By employing these precautionary measures and procedures to reduce BPA contamination from the analytical procedure, we could accurately determine l(-10) ppt of BPA in environmental water samples using a column switching HPLC system.     

Preparation and certification of the new reference materials; plastics (disk form, JSAC 0621-0625) for determination of mercury using x-ray fluorescent analysis.

The Japan Society for Analytical Chemistry has developed some new plastic certified reference materials (CRMs) for the analysis of mercury in polyester disks using XRF analysis. These CRMs (named as JSAC 0621-0625) were prepared by casting polyesters including a toluene solution of organometallic compounds as a standard. Concentrations of the five levels of mercury ranged from 0 to 250 mg/kg. Homogeneity tests of prepared disks had shown excellent results. Interlaboratory comparison study for the certification was performed by 15 laboratory participants. The z-scores in robust statistical method was applied for the evaluation of outliers. The certified values were assigned after discarding outliers. The uncertainties of certified values were determined as the confidence levels of 95%.     

Preparation and properties of polyamides and polymides containing bibenzyl,stilbene, and tolan structures

Polyisophthalamides and polyterephthalamides were prepared by the solution polycondensation of the corresponding diacyl chlorides with 4,4′-diaminobibenzyl, trans-4,4′-diaminostilbene, and 4,4′-diaminotolan in N,N-dimethylacetamide (DMAc). Polypyromellitimides were synthesized in two steps by the ring-opening polyaddition of pyromellitic dianhydride with the aromatic diamines in DMAc, followed by thermal cyclodehydration. The amorphous polyisophthalamides were soluble in some amide solvents containing lithium chloride, while the polyterephthalamides having fair degree of crystallinity were insoluble in these solvents. The thermal stability of these aromatic polymers decreased in the order of the tolan-containing polymers > the stilbene-containing polymers > the bibenzyl-containing polymers, both in air and under nitrogen.     

Kinetic approach to radiation-induced grafting in the polyethylene–styrene system. II

The investigation method reported in the previous paper was applied to four reaction methods: preirradiation method with reaction in liquid monomer, preirradiation method with reaction in monomer vapor, simultaneous irradiation method in liquid, and simultaneous irradiation method in vapor. The increasing patterns and values of the degree of grafting experimentally obtained roughly agreed with those calculated by using the same rate constants. At high monomer concentration, the rate of grafting was small; at low monomer concentration, the rate of grafting was large. Strictly speaking, the data by simultaneous irradiation method were somewhat larger than those by calculation. Two additional factors, as homopolymerization and the grafting from the radicals formed on the grafted polystyrene, were considered and discussed. The rate constants obtained were also discussed.     

Synthesis of polyarylamines by vinylogous nucleophilic substitution polymerization of bis(4-chloro-3-nitrophenyl) sulfone with diamines

A series of new polyarylamines was prepared by the vinylogous nuclephilic substitution polymerization of bis(4-chloro-3-nitrophenyl) sulfone with both aromatic and aliphatic diamines. The synthesis involves the solution polycondensation in a polar aprotic solvent at elevated temperatures, a tertiary amine being used as an acid acceptor. Of these solvents, dimethyl sulfoxide and N-methyl-2-pyrrolidone were the most effective for the preparation of high molecular weight polymers. The polyarylamines having inherent viscosities in the range of 0.1–0.5 were all amorphous and highly soluble in polar aprotic solvents. Thermogravimetric analysis under both air and nitrogen atmospheres indicated that rapid decomposition began above 300°C for the polyarylamines from aromatic diamines.     

Preparation and properties of poly(imide-oxoisoindolobenzothiadiazine dioxides)

New thermally stable poly(imide-oxoisoindolobenzothiadiazine dioxides) (PIOD) have been prepared by the three-step cyclopolycondensation reaction of diaminobenzenesulfonamides with aromatic tetracarboxylic dianhydrides. The polymerization proceeded through the formation of poly(amic acid-sulfonamides) (PAAS), followed by cyclodehydration to yield polyimide-sulfonamides (PIS), which were subsequently converted to PIOD at 300°C. PAAS having inherent viscosities in the range of 0.1–0.5 in N-methyl-2-pyrrolidone (NMP) were obtained in approximately quantitative yield. PIOD were insoluble in most organic solvents, whereas PAAS and PIS were soluble in NMP and dimethyl sulfoxide. Differential thermal analysis and thermogravimetric analysis indicated that PIOD began to decompose at 460°C in air. The cyclodehydration of the model compounds was also investigated.     

Novel ring transformation reactions of xanthine derivatives

The novel ring transformation reactions were found in the reactions of 1,3,7,9-tetra-alkyl-8,9-dihydroxanthines and acetylenic compounds. The reaction of the dihydroxanthine with DMAD gave a propellane type compound and with methyl propiolate afforded the similar type compound and a pyrimido[4,5-b]diazepine derivative. The mechanism of these reactions was also discussed.     

Synthesis of polyphthalimidines with benzylidene group from aminophthalide monomers

Two aminophthalide monomers, 6-amino-3-benzylidenephthalide (I) and 3-(p-aminobenzylidene)phthalide (II), underwent self-polycondensation in o-phenylphenol at 250°C to yield polyphthalimidines with inherent viscosities up to 0.5 dL/g. These polymers were readily soluble in a variety of solvents such as dimethylformamide, dimethyl sulfoxide, m-cresol, pyridine, and methylene chloride. The temperatures at which a 10% weight loss occurred by thermogravimetry in nitrogen were 460°C for the polymer derived from I and 490°C for the polymer from II. The glass transition temperature of the polymer from I was 332°C, determined by thermomechanical analysis.