Preparation of Sr2CeO4:Eu3+,Dy3+ white luminescence phosphor particles and thin films by using an emulsion liquid membrane system

Sr(2)CeO(4) and Sr(2)CeO(4):Eu(3+),Dy(3+) phosphor particles and thin films were prepared by using an emulsion liquid membrane (ELM, water-in-oil-in-water (W/O/W) emulsion) system, containing VA-10 (2-methyl-2-ethylheptanoic acid) as extractant (cation carrier). A two-step extraction enabled efficient extraction for Sr(3+) and rare earth ions, and the resulting precursor metal oxalate particles produced in the internal water phase of the ELM system were about 60 nm in diameter. Calcination of the oxalate particles in air gave submicrometer-sized Sr(2)CeO(4) and Sr(2)CeO(4):Eu(3+),Dy(3+) particles, which showed blue and white luminescence, respectively, by UV excitation. Blue and white luminescence phosphor thin films were also prepared by soaking alumina substrates into the W/O emulsion containing precursor oxalate particles, followed by calcination in air.     

Synthesis and properties of new crystalline poly(arylene ether nitriles)

Crystalline poly(arylene ether nitrile) could be prepared by the polycondensation of 2,6-dihalobenzonitrile with resorcinol at 200°C in N-methylpyrrolidone in the presence of sodium carbonate. A reaction temperature of at least 200°C was necessary to attain high molecular weight polymer. Spectral data indicated that the polymer had the structure of a poly(meta-phenylene ether) with pendent nitrile groups on every other phenylene unit. Despite this structure, the crystallinity and the crystallization rate of the polymer were greater than those of the corresponding polymer with a para-linked structure. The glass transition temperature and the melting temperature of the polymer were almost the same as those of poly(etheretherketone) (PEEK^TM). A series of other new poly(arylene ether nitriles) were also examined. The polymers derived from 4,4′-biphenol, dihydroxytetra-phenylmethane, dihydroxydiphenylsulfone, and 1,5-isoquinolinediol had high glass transition temperatures. The poly(arylene ether nitriles) exhibited excellent tensile strength compared with the corresponding ketone- or sulfone-containing polymers. Comparing the three different kinds of polymers containing the same bisphenol units, the order of glass transition temperature was found to be sulfone- > nitrile- > ketone-containing polymers, while the order of tensile strength was nitrile- > ketone- > sulfone-containing polymers. The excellent mechanical properties are attributable to dipole-dipole interactions of nitrile groups. © 1993 John Wiley & Sons, Inc.     

Electron spin resonance study of polymerization of butadiene with tris(acetylacetonato)titanium and triethylaluminum

ESR spectra of homogeneous catalyst derived from tris(acetylacetonato)titanium(III) and triethylaluminum were observed at several temperatures from ?78°C, to +25°C, at molar ratios of aluminum to titanium of 1–108. At ?78°C, this catalyst yields a violet complex which shows an ESR signal with a g value of 1.959 and is associated with the first intermediate. At ?40°C to ?30°C, this signal decreases, and two signals with g values of 1.947 and 1.960 are observed. The latter two signals diminish at ?5°C to +10°C, while two kinds of new signals with g values of 1.965 and 1.969 appear overlapping each other. The structures of the species corresponding to these five signals are discussed on the basis of the ESR spectra, the intensity change, and the unpaired spin distribution. A new signal with a g value of 1.978 is found in the presence of butadiene at 25°C at Al/Ti > 8 and is assigned to a growing end of polybutadiene with this catalyst. The polymer yield increases remarkedly at Al/Ti molar ratios greater than 10. The microstructure of the resulting polymer consists almost completely of 1,2 units. The structure of the growing end is proposed to be a titanium (III) species containing two 1-substituted allyl groups, by comparison with the structure ascribed to the growing end of polybutadiene with n-butyl titanate-triethylaluminum catalyst.     

Electron spin resonance study on polymerization of alkyl acrylates with n-butyl titanate(IV)–triethylaluminum catalyst

n-Butyl titanate(IV)–triethylaluminum catalyst at Al/Ti molar ratios greater than 6 polymerizes methyl and n-butyl acrylates at ?78°C. The polymerization system which includes methyl acrylate at ?78°C, gives two ESR signals with g factors of 1.958 and 1.961 that overlap each other. The absorption intensity of the latter signal is approximately proportional to the polymer chain concentration calculated from polymer yield and the molecular weight. The polymerization system at Al/Ti ratios smaller than 3 has no catalytic activity on the polymerization and shows only the ESR signal with the g factor of 1.958. On the basis of these facts the ESR signal with the g factor of 1.961 is attributed to the active growing end of poly(methyl acrylate) with this catalyst. The character of this active growing end is discussed.     

Polyiodide composition in poly(vinyl acetate)-iodine-iodide complex

Polyiodide formed by complexation of poly(vinyl acetate) (PVAc) with iodine in the presence of iodide has been investigated by chemical analysis and resonance Raman spectrophotometry. When PVAc films were immersed in iodide-iodine aqueous solutions which had different ratios of iodide to iodine concentration [I^?]/[I₂], the complex films exhibited tremendous variations of swelling degree, despite the relatively small change in the amount of bound iodine. From a quantitative chemical analysis, the composition of polyiodide bound to PVAc was found to be 1.01 ± 0.035 in the molar ratio of iodide to iodine irrespective of the composition of the iodide-iodine aqueous solution ([I^?]/[I₂] = 2–500). The polyiodide formed in PVAc-iodine-iodide complex was therefore inferred to be (I₃^?)_n. Resonance Raman spectra obtained on PVAc-iodine-iodide complexes were also identical to those of the benzamide-iodine complex, in which the polyiodide consists of (I₃^?)_n, consistent with the result from chemical analysis.     

Analysis of oxidized epigallocatechin gallate by liquid chromatography/mass spectrometry

(-)-Epigallocatechin gallate (EGCG) of catechins changes from non-colored at around neutral pH to yellow at higher pH region in aqueous solution. The pH-dependent oxidation of EGCG was analyzed by liquid chromatography/electrospray ionization tandem mass spectrometry (LC/ESI-MS/MS). LC/MS/MS analysis of EGCG and its related compounds, (-)-epicatechin gallate (ECG) and (-)-epigallocatechin (EGC), successfully elucidated the structure relationship of EGCG solution involving the color change reaction at different pH conditions. The oxidation species produced at alkaline pH was detected at a different retention time from EGCG in the chromatograms of the EGCG sample. The oxidation species was found to correspond to M+14 (where M is the molecular weight of EGCG), which has two hydrogen atoms removed and addition of one oxygen atom to the gallyl moiety in the B-ring of EGCG.     

Dithiol-mediated immobilization of CdS nanoparticles from reverse micellar system onto Zn-doped silica particles and their high photocatalytic activity

Cds nanoparticles, prepared in a reverse micellar system, were immobilized directly onto alkanedithiol-modified Zn-doped silica particles, which were themselves prepared via hydrolysis of tetraethylorthosilicate in the presence of Zn(NO(3))(2) followed by contact with dithiol molecules. The resulting CdS-Zn-SiO(2) composite was then used as a photocatalyst for the generation of H(2) from 2-propanol aqueous solution. Under UV irradiation (lambda>300 nm), a high photocatalytic activity was observed for the CdS-Zn-SiO(2) composite material. This is effected by electron transfer from the photoexcited ZnS (dithiol-bonded Zn on SiO(2)) to CdS nanoparticles. The photocatalytic activity is increased with a decrease in the number of methylene groups in the dithiol molecules, according to the rank order 1,10-decanedithiol <1,6-hexanedithiol <1,2-ethanedithiol.     

Reaction of 2-dialkylamino-5-phenyl-1,3-oxathiolium cation with sulphur ylides

The reaction of 2-dialkylamino-5-phenyl-1,3-oxathiolium cation 1 with sulphur ylides 2 was investigated. The behavior of 1 was solvent-dependent. In CH₂Cl₂, carbamate ester 3 was obtained: in CH₃CN, the intermediate sulphonium salt 5, which on hydrolysis gave 3, was isolated. On the other hand, reaction in MeOH gave the diphenacyl derivative 6. The reaction mechanism is discussed.     

Constituents of Crinoidea, 4. Isolation and structure of ceramides and glucocerebrosides from the feather star Comanthus japonica

Five ceramides, JC-1-JC-5, and four glucocerebrosides, JCer-1-JCer-4, have been isolated from their parent ceramide and glucocerebroside molecular species JC and JCer obtained from the less polar lipid fraction of the chloroform/methanol extract of the feather star Comanthus japonica. The structures of these sphingolipids have been determined on the basis of chemical and spectroscopic evidence. Reversed-phase HPLC was effective at isolating these sphingolipids, revealing very close resemblance in their structures. JC-1, JC-3, JC-4, JC-5 and JCer-2, JCer-4 are newly found ceramides and glucocerebrosides, respectively.     

Isolation and structure determination of six glucocerebrosides from the starfish Luidia maculata

Two new glucocerebrosides, luidiacerebroside A (2) and B (6), were isolated from the cerebroside molecular species obtained from the less polar fraction of the CHCl3/MeOH extract of the starfish Luidia maculata using HPLC. Four known cerebrosides, CE-2b (1), astrocerebroside B (3), acanthacerebroside B (4), and CE-3-2 (5) have also been isolated and characterized. The structures of these cerebrosides were determined on the basis of chemical and spectroscopic evidence. Mass spectrometry of dimethyl disulfide derivatives was useful for the determination of the double-bond position in the long-chain base.