Electronic structure of a cobalt monolayer on Cu(100)

Angular resolved photoemission spectra using synchrotron radiation have been measured for different amounts of cobalt evaporated on Cu(100). At room temperature cobalt grows layer-bylayer forming well-ordered layers in registry with the substrate, as judged by AES, LEED and UPS measurements. The energy position and linewidth of the Cu peaks remain unchanged when cobalt is deposited onto the surface, suggesting a rather weak interaction between the d-bands of Co and Cu. The two-dimensional band structure of the monolayer of cobalt has been determined. We have obtained a value for the magnetic exchange splitting of ΔE_exch = 0.80 ± 0.15 eV, which is nearly identical to the bulk value. A shift in the energy positions of the critical points for the monolayer versus bulk of cobalt is interpreted in terms of a narrower 2D density of states in the monolayer as compared to the bulk. A resonant valence-band two-electron satellite has been found. The correlation energy and screening effects of the two d-holes are very similar to the corresponding bulk values, while the decreased intensity of the satellite at resonance compared to the one for Co(0001) suggests that there are more d-states relative to s-states in the monolayer than in a bulk cobalt single crystal, in agreement with recent models of the valence band electronic structure at surfaces.     

Stimulated spin-flip emission from magnetic semiconductors

We show that by inverting the spin state population in a s-d model one might get a temperature tunable stimulated spin-flip emission line in ferromagnetic semiconductors.     

Self-assembled monolayers and chemical derivatization of Ba0.5Sr0.5TiO3 thin films: Applications in phase shifter devices

Thin films of barium strontium titanate (Ba_1−xSr_x TiO₃ (BSTO)) have been used in coupled microstrip phase shifters (CMPS) for possible insertion in satellite and wireless communication platforms primarily because of their high dielectric constant, low loss, large tunability, and good structural stability. In an attempt to improve the figure of merit K (phase shift °/dB of loss) of phase shifters, modification of the metal/BSTO interface of these devices has been done through surface modification of the BSTO layer using a self-assembled monolayer approach. The impact of this nanotechnology promises to reduce RF losses by improving the quality of the metal/BSTO interface. In this study, compounds such as 3-mercaptopropyltrimethoxysilane (MPS), 16-mercaptohexadecanois acid (MHDA) and 3-mercaptopropionic acid (MPA) were used to form the self-assembled monolayers on the BSTO surface. As a result of the previous modification, chemical derivatization of the self-assembled monolayers was done in order to increase the chain length. Chemical derivatization was done using 3-aminopropyltrimethoxysilane (APS) and 16-mercaptohexadecanoic acid. Surface chemical analysis was done to reveal the composition of the derivatization via X-ray photoelectron spectroscopy (XPS) and Fourier Transform Infrared (FT-IR). Low and high frequencies measurements of phase shifters were done in order measure the performance of these devices for insertion in antennas. X-ray photoelectron spectroscopy characterization of modified BSTO thin films with MPS showed a binding energy peak at 162.9 eV, indicative of a possible SO interaction: sulfur of the mercapto compound, MPS, used to modify the surface with the oxygen site of the BSTO thin film. This interaction is at higher binding energies compared with the thiolate interaction. This behavior is observed with the other mercapto compounds such as: MHDA and MPA. An FT-IR analysis present a band at 780 cm⁻¹, which is characteristic of an OSC stretching and reveals the modification of the BSTO thin film by the coupling of the O of the BSTO with the S of the mercapto compound. All the modification using mercapto compounds is through sulfur to the BSTO thin film. MHDA SAM on BSTO thin film was chemically derivatized using APS shown by XPS and FT-IR. The SAMs modified phase shifters showed an improvement in performance with respect to those phase shifters fabricated with standard methods.     

Experimental Study of the Influence of Changes in Load Direction on the Performance of a Crown Bearing

Laboratory tests have been carried out in order to investigate the influence of small changes in load direction on the performance of a steadily loaded hydrodynamic crown journal bearing. Hydrodynamic pressures, temperature distribution on the bush internal surface, shaft temperature, oil flow rate and bush torque were measured for fixed sets of operating conditions, at three different groove locations () with respect to the line of load ( = 0, –30, and +30 degrees). For each groove location quantitative information is provided concerning to the influence of applied load and shaft rotational speed on the performance characteristics. Changing the location of the groove around the load line did affect flow rate, bush torque and maximum hydrodynamic pressure, but only had a slight effect on bush maximum temperature.     

Experimental evidence for a light and broad scalar resonance in D(+) --> pi(-)pi(+)pi(+) decay

From a sample of 1172 +/- 61 D(+)-->pi(-)pi(+)pi(+) decays, we find gamma(D(+)-->pi(-)pi(+)pi(+))/gamma(D(+)-->K-pi(+)pi(+)) = 0.0311 +/- 0.0018(+0.0016)(-0.0026). Using a coherent amplitude analysis to fit the Dalitz plot of these decays, we find strong evidence that a scalar resonance of mass 478(+24)(-23) +/- 17 MeV/c(2) and width 324(+42)(-40) +/- 21 MeV/c(2) accounts for approximately half of all decays.     

Novel microscopic mechanism of intermixing during growth on soft metallic substrates

Generic computer simulations using empiric interatomic potentials suggest a new, collective mechanism that could be responsible for mixing at heteroepitaxial interfaces. Even if single adsorbate atoms diffuse by hopping on the substrate surface and do not mix at the terraces, two-dimensional islands formed by nucleation may become unstable above a certain critical size and explode upwards forming clusters of several atomic layers. This process is accompanied by strong distortions of the underlying atomic layers, and on soft materials it can result in surface etching and incorporation of substrate atoms into the islands.     

Polystyrene/decahydronaphthalene/propane phase equilibria and polymer conformation properties from intrinsic viscosities

The influence of dissolved propane (up to 31.2 wt %) on the phase equilibria of 5 wt % polystyrene (PS) dissolved in 66/34 wt % trans/cis‐decahydronaphthalene (DHN) was measured over the temperature range of 323–423 K. A suitable temperature, pressure, and propane composition operating space was defined to measure intrinsic viscosities of a single fluid phase. Intrinsic viscosities of PS in cosolvent mixtures of propane and trans/cis‐DHN were measured between 323 and 423 K and between 70 and 208 bar. The addition of propane to the isomeric mixture of DHN resulted in a decreased solvent quality for PS, causing a contraction of the PS coil. The most dramatic decrease in solvent quality with the addition of propane occurred at 323 K and 70 bar with approximately a 36% reduction in the viscometric radius with the addition of 45 mol % propane to DHN. At 423 K, the solvent quality was less sensitive to the addition of propane and only a 13% reduction in the viscometric radius was observed at 70 bar and 45 mol % propane in DHN. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011