Crystallographic report: Crystal structure of a one‐dimensional zinc(II) coordination polymer containing 4,4′‐biphenyldicarboxylate hemihydrate

A one‐dimensional zinc(II) coordination polymer has been constructed from zinc(II), 4,4′‐biphenyldicarboxylate and pyridine in which each zinc(II) atom is coordinated by two pyridine ligands and two monodentate 4,4′‐biphenyldicarboxylate ligands that define a distorted tetrahedral geometry. Copyright © 2003 John Wiley & Sons, Ltd.     

Preparation,thermal properties,and flame retardance of epoxy–silica hybrid resins

A novel epoxy system was developed through the in situ curing of bisphenol A type epoxy and 4,4′‐diaminodiphenylmethane with the sol–gel reaction of a phosphorus‐containing trimethoxysilane (DOPO–GPTMS), which was prepared from the reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) with 3‐glycidoxypropyltrimethoxysilane (GPTMS). The preparation of DOPO–GPTMS was confirmed with Fourier transform infrared, ¹H and ³¹P NMR, and elemental analysis. The resulting organic–inorganic hybrid epoxy resins exhibited a high glass‐transition temperature (167 °C), good thermal stability over 320 °C, and a high limited oxygen index of 28.5. The synergism of phosphorus and silicon on flame retardance was observed. Moreover, the kinetics of the thermal oxidative degradation of the hybrid epoxy resins were studied. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2354–2367, 2003     

A retractable structure based on Bricard linkages and rotating rings of tetrahedra

Retractable structures which alter their geometries according to practical requirements are widely used in roof structures of stadiums for their versatility. A retractable structure based on threefold-symmetric Bricard linkages and rotating rings of tetrahedra is proposed and developed in this paper. By replacing each link of a threefold-symmetric Bricard linkage with a tetrahedron, a retractable structure is obtained which can repeatedly open and close by rotating the tetrahedra. The geometric relationship between the retractable structure and the threefold-symmetric Bricard linkage is derived and ranges of main geometric parameters are determined to ensure a continuous and smooth movement in the deployment of the structure. Then the relative displacement of the support and the open rate of the structure, two main parameters concerned in practical applications, are investigated. Preferred ranges of main geometric parameters are proposed and a physical model is manufactured to verify them. A discussion on some possible improvements and modifications of the structure is also presented.     

Synthesis and characterization of wholly aromatic poly(azomethine)s containing donor–acceptor triphenylamine moieties

N‐(4‐nitrophenyl)‐4′,4″‐bisformyl‐diphenylamine was synthesized from N‐(4‐nitrophenyl)‐diphenylamine by the Vilsmeier‐Haack reaction. Soluble aromatic poly(azomethine)s (PAMs) were prepared by the solution polycondensation of N‐(4‐nitrophenyl)‐4′,4″‐bisformyl‐diphenylamine and aromatic diamine in N‐methyl‐2‐pyrrolidone (NMP) at room temperature under reduced pressure. All the PAMs are highly soluble in various organic solvents, such as N,N‐dimethylacetamide (DMAc), chloroform (CHCl₃), and tetrahydrofuran (THF). Differential scanning calorimetry (DSC) indicated that these PAMs had glass‐transition temperatures (T_gs) in the range of 170–230 °C, and a 10% weight‐loss temperatures in excess of 490 °C with char yield at 800 °C in nitrogen higher than 60%. These PAMs in NMP solution showed UV‐Vis charge‐transfer (CT) absorption at 405–421 nm and photoluminescence peaks around 462–466 nm with fluorescence quantum efficiency (Φ_F) 0.10–0.99%. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of these PAMs can be determined from cyclic voltammograms as 4.86–5.43 and 3.31–3.34 eV, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4921–4932, 2007     

Metallo‐supramolecular micelles: Studies by analytical ultracentrifugation and electron microscopy

In aqueous solutions, amphiphilic block copolymers in which a polystyrene (PS) segment is connected to a poly(ethylene oxide) (PEO) block via a bis(2,2′:6′,2″‐ terpyridine ruthenium) complex can form micelles. Such micelles of the protomer type PS₂₀‐[Ru]‐PEO₇₀, according to the preparation procedure representing frozen micelles, were studied by sedimentation velocity and sedimentation equilibrium analysis in an analytical ultracentrifuge and by transmission electron microscopy, with different techniques applied for the sample preparation. The particles obtained were surprisingly multifarious in size. In ultracentrifugation experiments performed at relatively low salt concentrations, the distributions of the sedimentation coefficient s_20,w showed a pronounced peak at 9.6 S and a broad, only partly separated second peak around 14 S. The molar mass of the particles at the peak was around 430,000 g/mol, corresponding to an aggregation number of approximately 85. The average hydrodynamic diameter of the particles in the peak fraction was approximately 13 nm. In electron micrographs of negatively stained samples, spheres of diameters between 10 and 25 nm were the most abundant particles, but larger ones with a wide size range were also visible. The latter particles apparently were composed of smaller ones. The data from both sedimentation analysis and electron microscopy showed that (1) the studied compound formed primary micelles of diameters around 20 nm and (2) the primary micelles had a tendency toward aggregation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3159–3168, 2003     

Diffusion via splitting and remeshing via merging in vortex methods

The technique of splitting a fat vortex element (with a core width larger than some threshold) into some thin ones in order to fix the convergence problem of the core‐spreading vortex methods is convenient and efficient. In particular, it keeps the method purely Lagrangian. In the present investigation, the splitting process is further viewed as part of the physical diffusion process. A new splitting method in which several weaker child vortices surround a thinned but still strong parent vortex is proposed. It is found that because of the survival of the parent vortex, the error arising from the splitting events can be largely reduced. The computational amount on the other hand is kept reasonably large by merging similar and close‐by vortices. The merging scheme designed herein not only involves fewer restrictions but also allows merging vortices of opposite rotations through the viewpoint of remeshing. The validity and accuracy of these techniques, proposed particularly for simulations undergoing lots of splitting and merging events, are verified by successfully simulating the interactions between two Burgers vortices under an external straining field. Copyright © 2005 John Wiley & Sons, Ltd.     

Behaviors of the positive temperature coefficient of resistance of poly(styrene‐co‐n‐butylacrylate) filled with Ni‐plated core‐shell polymeric particles

Conductive composite films of poly(styrene‐co‐n‐butylacrylate) copolymers filled with low‐density, Ni‐plated core‐shell polymeric particles were prepared and their behaviors of positive temperature coefficient of resistance (PTCR) were investigated. When the conductive fillers in the composite film were loaded beyond the critical volume, 10 up to 25 vol %, composite films exhibited a unique electrical resistant transition behavior, which the electrical resistance rapidly increased by several orders of magnitude at the critical temperature. The PTCR transition temperature, in general, occurred before the glass transition temperature of polymer matrix. Further increased the conductive filler loading to 30 vol %, the overpacked conduction paths were formed in the entire composite and the PTCR effects became blurred. While the composite film treated with thermal cycle several times from room temperature up to 120 °C, the electrical resistivity increased accompanied with the shift of the PTCR transition to lower temperature. The reason might have been caused by the formed interfacial cracks within the composite film. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 322–329, 2007