Application of MMMA method: Dispersed superconductors and magnetic nanolayers

Microwave nonresonant dissipation observed around zero field makes a powerful method in characterizing superconducting state (to determineT _C,H _C1,H _CJ parameters). This review shows several successful applications of magnetically modulated microwave absorption (MMMA). MMMA enables to study MgB₂ superconducting nanoregions embedded in the Mg host structure. Application of MMMA to study intercalation of fullerence enabled the observation of a new superconducting phase. The pressure effect dT _C/dp has been studied below the percolation threshold in YBaCuO/PST composites. The local temperature of the Josephson junction measured by the MMMA technique showed that a granular superconductor consists of two phases: host phase and Josephson junction system. MMMA has been applied lately to separate the giant magnetoresistance from the magnetization effect in differential hysteresis loops.     

A remark on divisibility of definable groups

We show that if G is a definably compact, definably connected definable group defined in an arbitrary o‐minimal structure, then G is divisible. Furthermore, if G is defined in an o‐minimal expansion of a field, k ∈ ? and p_k : G → G is the definable map given by p_k (x ) = x^k for all x ∈ G , then we have |(p_k )^–1(x )| ≥ k^r for all x ∈ G , where r > 0 is the maximal dimension of abelian definable subgroups of G . (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Ein Doppelaspirator

Ohne Zusammenfassung     

Effect of short glass fiber on structure and viscoelastic behavior of olefinic polymers synthesized with metallocene catalyst

Several composites were prepared on the basis of an ethylene homopolymer and different copolymers of ethylene and 1‐hexene, synthesized with a metallocene catalyst, as matrices and a content of a 5 wt % of short glass fiber. The effect of the fiber incorporation on the structure and mechanical and viscoelastic behaviors was analyzed for the different samples. The glass fibers induced a slightly higher crystallinity, and the crystallite morphology significantly changed (long spacings and crystal orientation). The incorporation of fibers did not reinforce the different matrices under study at this low content; consequently, the mechanical parameters, such as Young's modulus, yielding stress, and microhardness, were lower in the composites as compared with those values found in the neat polyolefins. The location and apparent activation energies of distinct relaxation processes are also discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1244–1255, 2003     

Ultrasonic spectroscopic evaluation of the ring‐opening metathesis polymerization of dicyclopentadiene

An in situ ultrasonic spectroscopy technique was used to study the ring‐opening metathesis polymerization of dicyclopentadiene catalyzed by bis(tricyclohexylphosphine)benzylidene ruthenium dichloride. A reaction cell employing a flexible poly(ethylene terephthalate) window for pulse echo ultrasonic spectroscopy was used to monitor the polymerization. The changes in the density, wave speed, acoustic modulus, and attenuation were all simultaneously monitored. In comparison with Fourier transform infrared (FTIR) spectroscopy data, the changes in the density, velocity, and modulus only accurately measured the rate constant for the metathesis of the cyclopentyl unsaturation. The ultrasonic values were within 6% of the values determined by FTIR. The activation energy for metathesis of the cyclopentyl unsaturation was 84 kJ mol^?1, following first‐order kinetics. Rate constants for the polymerization of the norbornyl unsaturation could not be determined by ultrasound. The gel point, vitrification, and qualitative information about the reaction rate could be determined from the change in the attenuation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1323–1333, 2003     

Mechanisms of n‐butanol formation in butyl acrylate latexes

The mechanisms involved in the formation of n‐butanol during the synthesis of butyl acrylate containing latices were investigated. The experimental results showed that neither the hydrolysis of butyl acrylate nor of the ester bond in the butyl acrylate segments of the polymer played a major role in the formation of n‐butanol, which was mainly generated from the polymer backbone, by transfer reactions to polymer chain followed by cyclization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5838–5846, 2007     

Multi-mode wave propagation in ribbed plates: Part I,wavenumber-space characteristics

This paper addresses the issue of energy propagation features in ribbed panels over a wide frequency range. First, a tool for estimating the wave propagation characteristics of one- and two-dimensional structures by k-space analysis is presented. This tool uses a concept of Inhomogeneous Wave Correlation with sparse measured or extracted data, and leads to the estimation of θ-dependent wavenumbers. Here, the method is employed with the sparse simulated and measured normal velocities of a set of ribbed panels and new insights into their k-space behavior are highlighted. Behavior is essentially characterized at low frequencies by structural orthotropy. Comparisons with homogenized data show very good agreement. At higher frequencies, a new behavior pattern is observed and explained both numerically and experimentally. This is a multi-modal waveguide type of propagation in a direction parallel to the ribs.     

Buckling of a stiff thin film on a compliant substrate in large deformation

A finite-deformation theory is developed to study the mechanics of thin buckled films on compliant substrates. Perturbation analysis is performed for this highly nonlinear system to obtain the analytical solution. The results agree well with experiments and finite element analysis in wavelength and amplitude. In particular, it is found that the wavelength depends on the strain. Based on the accurate wavelength and amplitude, the membrane and peak strains in thin films, and stretchability and compressibility of the system are also obtained analytically.     

Multi-layer thin films/substrate system subjected to non-uniform misfit strains

Current methodologies used for the inference of thin film stress through curvature measurement are strictly restricted to stress and curvature states that are assumed to remain uniform over the entire film/substrate system. These methodologies have recently been extended to a single layer of thin film deposited on a substrate subjected to the non-uniform misfit strain in the thin film. Such methodologies are further extended to multi-layer thin films deposited on a substrate in the present study. Each thin film may have its own non-uniform misfit strain. We derive relations between the stresses in each thin film and the change of system curvatures due to the deposition of each thin film. The interface shear stresses between the adjacent films and between the thin film and the substrate are also obtained from the system curvatures. This provides the basis for the experimental determination of thin film stresses in multi-layer thin films on a substrate.     

Closed-form solutions for a rectangular layer with central crack under anti-plane shear stress

We consider the problem of determining the stress distributionin a finite rectangular elastic layer containing a Griffithcrack which is opened by internal shear stress acting alongthe length of the crack. The mode III crack is assumed to belocated in the middle plane of the rectangular layer. The followingtwo problems are considered: (A) the central crack is perpendicularto the two fixed lateral surfaces and parallel to the othertwo stress-free surfaces; (B) all the lateral surfaces of therectangular layer are clamped and the central crack is parallelto the two lateral surfaces. By using Fourier transformations,we reduce the solution of each problem to the solution of dualintegral equations with sine kernels and a weight function whichare solved exactly. Finally, we derive closed-form expressionsfor the stress intensity factor at the tip of the crack andthe numerical values for the stress intensity factor at theedges of the cracks are presented in the form of tables.