Property changes of electroplated Cu/Co alloys and multilayers by organic additives

We investigated the change of magnetic properties of the electroplated Cu/Co alloys and multilayers caused by organic additives and high temperature annealing. When plated with a pure Cu/Co electrolyte, the alloy contained ∼25% of Cu and ∼75% of Co. The alloy was made of hcp-Co, fcc-Co and Cu(1 1 1) and was super-paramagnetic at room temperature. As we add a few organic additives in the plating electrolyte, the hcp-Co of the films disappeared. The organic additives contained in the electrolytes changed paramagnetic Cu/Co multilayers to ferromagnets. High-temperature thermal annealing increased coercivity due to the growth of the Co grains.     

Evaluation of closed-vessel microwave digestion method for the determination of trace impurities in polymer-based photoresist by inductively coupled plasma mass spectrometry

A closed microwave digestion method followed by inductively coupled plasma spectrometric (ICP-MS) analysis was evaluated for the determination of trace impurities in photoresist. To optimize the digestion procedure, several digestion parameters such as acid, heating temperature and heating time were evaluated. Besides, the digestion efficiency of used photoresist material and the recovery of analyte elements obtained by the use of gravimetric method and ICP-MS measurement, individually, were also compared to clarify the completeness of digestion. According to our experiments, the gravimetric method was found to be not so relevant to the completeness of digestion, because the remaining sample matrix could cause suppression effect in the subsequent ICP-MS measurement. In view of minimizing blank value and working time, a simple single-step heating program was proposed to mineralize 0.25 ml of photoresist material with 5 ml of nitric acid at 180 °C for 10 min. Based on the comparative study of the analytical results obtained by instrumental neutron activation analysis (INAA) and proposed method, the reliability of proposed method for the determination of trace metallic impurities in photoresist material has been confirmed.     

Formation of p-type ZnO film on InP substrate by phosphor doping

ZnO thin film was initially deposited on InP substrate by radio frequency (rf) magnetron sputtering and the diffusion process was performed using the closed ampoule technique where Zn₃P₂ was used as the dopant source. To verify the junction formation of ZnO thin films, the electrical properties were measured, and the effects of Zn₃P₂ diffusion on ZnO thin films were investigated. It is observed that the electrical property of the film is changed from n-type to p-type by dopant diffusion effect. Based on the results, it is confirmed that ZnO thin films can be a potential candidate for ultraviolet (UV) optical devices.     

Investigation of the chemical state of ultrathin Hf-Al-O films during high temperature annealing

Al₂O₃ incorporated HfO₂ films grown by atomic layer deposition (ALD) were investigated by high-resolution X-ray photoelectron spectroscopy (HRXPS). The core level energy state of a 15 Å thick film showed a shift to higher binding energy, as the result of a silicate formation and Al₂O₃ incorporation. The incorporation of Al₂O₃ into the HfO₂ film had no effect on silicate formation at the interface between the film and Si, while the ionic bonding characteristics and hybridization effects were enhanced compared to a pure HfO₂ film. The dissociation of the film in an ultrahigh vacuum (UHV) is effectively suppressed compared to a pure HfO₂ film, indicating an enhanced thermal stability of Hf-Al-O. Any dissociated Al₂O₃ on the film surface was completely removed into the vacuum by vacuum annealing treatment over 850 °C, while HfO₂ contributed to Hf silicide formation on the film surface.     

Assessment of thermal expansion coefficient of methylsilsesquioxane thin film

For the methylsilsesquioxane film whose optical birefringence is almost zero, it was recently reported that its vertical thermal expansion coefficient (CTE) was approximately one order of magnitude larger than the lateral CTE. Though the birefringence is not an absolute predictor of anisotropic behavior, the discrepancy in both the CTEs was so remarkable that it was essential to investigate whether the anisotropy was intrinsic property or not. If the effect of Poisson's ratio is considered in the calculation of the vertical CTE and when elastic modulus measured by surface acoustic wave spectroscopy is used in the assessment of the lateral CTE, both the CTEs are coincident with each other. Therefore, it can be concluded that the discrepancy in the CTEs can be attributed to a higher in‐plane polymer chain orientation but it can also arise from the misleadingly assumed modulus and Poisson's ratio. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3109–3120, 2006     

A novel strategy to verification of adulteration in alcoholic beverages based on Schlieren effect measurements and chemometric techniques

A novel strategy to evaluation of adulteration in alcoholic beverages based on the measurement of the Schlieren effect using an automated FIA system with photometric detection is proposed. The assay is based on the Schlieren effect produced when beverage samples are injected in a single-line FIA system that uses water as carrier stream and a light-emitting diode-phototransistor photometer controlled by microcomputer as detector. The flow system presents limited mixing conditions which make possible to create gradients of refractive index (Schlieren effect) in the injected sample zone. These gradients are reproducible, characteristic of each alcoholic beverage and undergo specific modifications when adulterations with water or ethanol are imposed. Schlieren effect data of brandies, cachaças, rums, whiskies and vodkas were treated by SIMCA to elaborate class models applied in the evaluation of alcoholic beverages adulteration. Samples of the original matrix of each sort of beverages were adulterated in laboratory by adding water, methanol and ethanol in levels of 5% and 10% (v/v). These samples were used as test set to validate SIMCA class models. The verification of authenticity using Schlieren effect measurements presented good results making possible to identify 100% of the beverages samples adulterated in laboratory and 93% of the actual adulterated alcoholic beverages with confidence levels of 95%. As principal advantage, the automated system does not use reagents to carry out the analysis.     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

The Ends of Manifolds with Bounded Geometry, Linear Growth and Finite Filling Area

We prove that simply connected open manifolds of bounded geometry, linear growth and sublinear filling growth (e.g. finite filling area) are simply connected at infinity.