Chromium(III) complexes with terdentate 2,6-bis(azolylmethyl)pyridine ligands: Synthesis, structures and ethylene polymerization behavior

Reactions of 2,6-bis(bromomethyl)pyridine with 3,5-dimethylpyrazole and 1H-indazole yield the terdentate ligands 2,6-bis(3,5-dimethylpyrazol-1-ylmethyl)pyridine (5) and 2,6-bis(indazol-2-ylmethyl)pyridine (6). The molecular structure of the new compound 6 was determined by single-crystal X-ray diffraction. These ligands react with the CrCl₃(THF)₃ complex in THF to form neutral complexes of general formula [CrCl₃{2,6-bis(azolylmethyl)pyridine-N,N,N}] (7, 8) which are isolated in high yields as stable green solids and characterized by means of elemental analysis, magnetic moments, IR, and mass spectroscopy. Theoretical calculations predict that the thermodynamically preferred structure of the complexes is the fac configuration. After reaction with methylaluminoxane (MAO) the chromium(III) complexes are active in the polymerization of ethylene.     

Thermo‐ and pH‐responsive gradient and block copolymers based on 2‐(2‐methoxyethoxy)ethyl methacrylate synthesized via atom transfer radical polymerization and the formation of thermoresponsive surfaces

A series of gradient and block copolymers, based on 2‐(2‐methoxyethoxy)ethyl methacrylate (MEO₂MA) and tert‐butyl acrylate (^tBA), were synthesized by atom transfer radical polymerization (ATRP) in a first step. The MEO₂MA monomer leads to the production of thermosensitive polymers, exhibiting lower critical solution temperature (LCST) at around room temperature, which could be adjusted by changing the proportion of ^tBA in the copolymer. In a second step, the tert‐butyl groups of ^tBA were hydrolyzed with trifluoroacetic acid to form the corresponding block and gradient copolymers of MEO₂MA and acrylic acid (AA), which exhibited both temperature and pH‐responsive behavior. These copolymers showed LCST values strongly dependent on the pH. At acid pH, a slightly decrease of LCST with an increase of AA in the copolymer was observed. However, at neutral or basic conditions, ionization of acid groups increases the hydrophilic balance considerably raising the LCST values, which even become not observable over the temperature range under study. In the last step, these carboxylic functionalized copolymers were covalently bound to biocompatible and biodegradable films of poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(HB‐co‐HHx)] obtained by casting and, previously treated with ethylenediamine (ED) to render their surfaces with amino groups. Thereby, thermosensitive surfaces of modified P(HB‐co‐HHx) could be obtained. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Kinetics and mechanism of the reactions of S-2,4-dinitrophenyl 4-substituted thiobenzoates with secondary alicyclic amines

[reaction: see text] The title reactions, in 44 wt % ethanol-water at 25.0 degrees C, exhibit slightly curved Br?nsted-type plots (log kN versus pKa of amines) with slopes beta1 = 0.1-0.44 (at high pKa) and beta2 ca. 0.7 (at low pKa). The magnitude of some of these slopes, together with the fact that the curvature center (pKa(0) = 9.5-10.8) does not change with the electronic effects of the benzoyl substituent, suggests that these reactions are not stepwise, but concerted.     

An advantageous route to oxcarbazepine (trileptal) based on palladium-catalyzed arylations free of transmetallating agents

[reaction: see text] A new route to oxcarbazepine (Trileptal), the most widely prescribed antiepileptic drug, starting from commercially available 2'-aminoacetophenone and 1,2-dibromobenzene, is reported. The sequentially accomplished key steps are palladium-catalyzed intermolecular alpha-arylation of ketone enolates and intramolecular N-arylation reactions. After several experiments to establish the best conditions for both arylation processes, the target oxcarbazepine is obtained in a satisfactory overall yield, minimizing the number of steps and employing scalable catalytic procedures developed in partially aqueous media.     

The signal/noise of an HMBC spectrum can depend dramatically upon the choice of acquisition and processing parameters

The effect of various acquisition and processing parameters on the sensitivity of HMBC spectra for typical organic molecules has been systematically investigated. For molecules in the 200–600 molecular weight range, an acquisition time of 0.2 to 0.4 s, a recycle time of no more than 1.0 s, optimization for ⁿJ_CH = 8 Hz and 512 time increments (with two‐ to fourfold linear prediction) are recommended. Some form of sine bell weighting along f₂ and either Gaussian or sine bell weighting along f₁ is suggested. The use of a 0.1‐s acquisition time and/or Gaussian or exponential weighting along f₂ can result in dramatic sensitivity loss, particularly for correlation peaks involving protons with complex splitting patterns, and should be avoided. Copyright © 2009 John Wiley & Sons, Ltd.     

The 3-connected binary matroids with circumference 6 or 7

In this paper, we construct all 3-connected binary matroids with circumference equal to 6 or 7 having large rank.     

Design and Tuning of Photoswitches for Solar Energy Storage

Current energy demand makes it compulsory to explore alternative energy sources beyond fossil fuels. Molecular solar thermal (MOST) systems have been proposed as a suitable technology for the use and storage of solar energy. Compounds used for this application need to fulfil a long series of requirements, being the absorption of sunlight and the energy stored some of the most critical. In this paper, we study different families of well-known molecular photoswitches from the point of view of their potential use as MOST. Starting from basic structures, we use density functional theory (DFT) computational modelling to propose two different strategies to increase the energy difference between isomers and to tune the absorption spectrum. The inclusion of a mechanical lock in the structure, via an alkyl chain and the presence of a hydrogen bonding are shown to directly influence the energy difference and the absorption spectra. Results shown here prove that these two approaches could be relevant for the design of new compounds with improved performance for MOST applications.