Co-immobilization of polymeric luminol,iron(II) tris(5-aminophenanthroline) and glucose oxidase at an electrode surface,and its application as a glucose optrode

The anodic polymerization of 3-aminophthalhydrazide (luminol) and iron(II) tris 5-aminophenanthroline (Fe(phen-NH2)3(2+)) has been reported in this paper. A bilayer electrode was developed based on these polymers and the ITO conductive glass (denoted ITO[Fe(phen-NH2)3(2+)]luminol electrode). This electrode emitted light (lambdaem: 430 nm) as it was brought into contact with H2O2. At pH 10, the resulting electrochemiluminescence (ECL) showed a linear relationship with the concentration of H2O2 in the range of 10 microM(-1) mM. This bilayer electrode also showed an application potential for the detection of glucose after being further modified with glucose oxidase (denoted ITO[Fe(phen-NH2)3(2+)]luminol]GOx electrode). Although the resulting ECL decayed more rapidly in concentrated glucose solutions (e.g., I M) because of the consumption of luminol during use, the decay became less severe in diluted glucose solutions (e.g., 10 mM). According to the flow injection analysis, a linear relationship existed between the ECL and the concentration of glucose from 10(-5)-10(-3) M at pH 9. The detection limit could reach a level of 5 x 10(-5) M at this pH.     

稀土在鼠肝中的物种分布

采用 ICP-MS、微量蛋白层析分离技术 ,研究了长时间、低剂量混合稀土及短时间、高剂量硝酸镧分别对大鼠及小鼠作用后 ,稀土在鼠肝中的代谢累积及其物种分布 .结果表明 ,鼠肝中各稀土含量随给药剂量的增加而增大 ,其累积速度大小顺序为 La>Ce>Nd>Pr;经柱层析分离未得到与稀土特异结合的鼠肝蛋白 ;稀土可与多种鼠肝蛋白 (包括多种重要的酶 )结合 ,在一定条件下 ,稀土与其结合蛋白可发生解离     

C(2×2)S/Fe(001)吸附体系的SCF-Xa-MS研究

采用SCF-X_α-MS方法, 对于C(2×2)S/Fe(001)吸附体系, 选择Fe_5S和Fe_9S两种原子簇模型, 研究了该吸附体系的电子结构、吸附成键特征及其相互作用图象。结果表明, S吸附于Fe(001)单晶表面具有较强的定域性质, S原子与底物Fe原子之间的吸附相互作用主要表现为S(3p)-Fe(4s,3d)之间的轨道相互作用。通过对表面吸附键长的优化, 其结果与X.S.Zhang等的ARPEFS的实验结果一致。     

Effect of the Secondary Reduction on the Enantioselectivity and Function of Additives in the Chiral Oxazaborolidine‐Catalyzed Asymmetric Borane Reduction of Ketones

The secondary reduction in the direct and oxazaborolidine‐catalyzed asymmetric borane reduction of ketones was investigated by the use of GC/MS tracing titration and control experiments. The results indicate that the secondary reduction affects the enantioselectivity only in noncoordinated solvents at low temperature and not under the usual catalytic reduction conditions because the intermediate alkoxyborane is unstable and quickly converts to borane and dialkoxyborane. The function of an alcohol additive in the asymmetric borane reduction of ketones is to consume excess borane in the reduction system thus inhibiting noncatalytic reduction, which leads to increased enantioselectivity in the catalytic reduction.     

Selenium Nanoparticles Prepared from Reverse Microemulsion Process

Selenium nanoparticles were prepared by a reverse microemulsion system. Sodium selenosulfate was used as selenium source. The results showed that hydrochloric acid concentration and reaction temperature had great influence on the morphology of products. The crystalline selenium nanowires and amorphous selenium nanorods were obtained in given condition.     

PU大分子单体水溶液性质

双亲聚合物一般由亲水和亲油 2种链段构成 ,有嵌段型[1,2 ] 和接枝型[3 ] 2种 ,其中通过大分子单体法合成双亲接枝聚合物备受关注[4] 。如以亲水性大分子单体和亲油性小分子单体共聚 ,大分子单体构成共聚物主链上支链 ,具有较大活动性 ,亲水效能高。采用对氯甲基苯乙烯[5] 或甲基丙烯酰氯[6] 与聚氧化乙烯大分子的一端相反应 ,可得到亲水性大分子单体 ,但其分子量及结构变化有限。本文采用常规条件 ,合成了嵌段式水溶性聚氨酯大分子单体 ,其分子量较大 ,共聚接枝的支链较长。利用该大分子单体具有非离子高分子表面活性剂的性质 ,采用无皂乳…     

Locally enhanced relative humidity for scanning probe nanolithography

The formation of a water meniscus between a sharp tip and a solid surface is one of the prevailing requirements for scanning probe microscope (SPM)-based lithographies, such as dip-pen nanolithography (DPN) and conductive tip induced oxidation. The water meniscus functions as a medium for the oxidation of or mass transfer to the solid surface. Here we report a simple, efficient, and effective approach to enhance the local relative humidity and thus increase the size of the water meniscus by bringing a water-containing capillary tube to the proximity of the tip-surface contact area. The enhancement in local relative humidity is confirmed via an increase in the measured tip-surface adhesion forces and the widths of DPN generated parallel lines. Compared to the global control of relative humidity for the whole lithography system, the short distance between the "water reservoir" and the tip-surface contact area enables rapid increase in the local vapor pressure of water, less perturbation, and minimal erosion to the state-of-the-art electronics. As a result, most scanning probe lithography experiments at high relative humidity can now be performed in a reasonable time frame.     

DMF-甲醇体系粘度与核磁共振化学位移的同时关联

提出了一个基于局部组成概念上的核磁共振模型. 利用该模型和以前别人提出的局部组成型粘度方程, 成功地同时关联属于传递性质的粘度数据和属于波谱性质的核磁共振化学位移数据，关联所得到化学位移的平均绝对偏差小于0.0072，粘度的平均绝对偏差小于0.0006 mPa•s，结果表明提出的局部组成模型是合理的.     

Fluorinated poly(arylene ether ketone)s bearing pentafluorostyrene moieties prepared by a modified polycondensation

The polycondensation of decafluorobenzophenone with hexafluorobisphenol A was modified by the addition of a molecular sieve dehydrating apparatus to the refluxing reaction system. This modification promoted the polymerization and enabled the reactions to be conducted in milder conditions and completed in a shorter time, thereby depressing side reactions such as branching and crosslinking. The resulting fluorinated poly(arylene ether ketone)s (FPAEK) were free of gel particles and possessed the designed molecular weights. This modified procedure was also suitable for introducing crosslinkable pentafluorostyrene (FSt) moieties into the polymers at the chain ends and/or inside the chain with the vinyl group of FSt being pendant. The resulting FSt containing fluorinated poly(arylene ether ketone)s (FPAEK‐FSt) can then be thermally crosslinked at 100 °C in the presence of 1% benzoyl peroxide (BPO) or at 250 °C without any initiator. The glass‐transition temperatures (T_g's) of FPAEK increased with increasing molecular weight and leveled off at about 147 °C for the polymer with a number‐average molecular weight of 18,600 Da, whereas the values were not apparently affected by the addition of FSt units. However, crosslinking of the FPAEK‐FSt resulted in an approximate 30 °C increase of the T_g. Spin‐coating FPAEK‐FSt onto silicon wafers followed by crosslinking gave films with excellent thermal stability, physical strength, and adhesion to the substrate as well as good reproducibility in terms of film preparation and optical properties. The refractive index and birefringence of the films measured at a wavelength of 1.55 μm were 1.502 and 2.5 × 10^?3, respectively. © 2002 Government of Canada. Exclusive worldwide publication rights in the article have been transferred to Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4205–4216, 2002     

黄原胶以三价铬交联的水凝胶的脱水行为

对黄原胶／三价铬水凝胶在７０，８０和９０℃下的脱水行为进行了研究．脱水与凝胶的交联密度即参与交联反应的三价铬的含量有密切联系．突发脱水之后的过程可以用一级反应动力学描述，反应速度常数随三价铬的浓度和温度的增高而增大，活化能为３４．５ｋｃａｌ／ｍｏｌ．一价盐（ＮａＣｌ）的含量对脱水过程没有影响．