载体对Cu基催化剂富氢条件下CO氧化性能的影响

燃料电池是一种高效和环境友好的能源装置,其中质子交换膜燃料电池（PEMFC）以其工作温度低、低温启动性能好、功率密度和能量转换效率高等优点而广受关注[1].目前,PEMFC所需要的氢气一般通过醇或烃类的重整获得,但所得的氢气含有浓度较高的、使燃料电池Pt电极中毒的CO,导致电池失效,CO的选择性（优先）催化氧化（PROX）在众多去除CO的方法中被认为是最直接有效的一种.     

微波辐射下秸秆纤维微观结构的变化

利用原子力显微镜(AFM)对微波处理前后秸秆纤维表面的变化进行了研究,并结合XRD和FTIR研究了处理前后其化学结构及结晶形态的变化情况。结果表明,未经微波处理的秸秆纤维表面比较光滑,平均粗糙度(Ra)为(86.7±6.335)nm,均方根粗糙度(Rq)为(141.1±9.055)nm;经微波处理的秸秆纤维表面比较粗糙,并出现许多细小孔洞,其Ra为(445.0±28.14)nm,Rq为(558.9±33.458)nm,微波辐射处理前后秸秆纤维的表面形态差异较大。经微波辐射处理后,秸秆纤维在2θ=22.3°处的衍射峰移至21.8°,且峰宽稍有增加,在38.1°、44.3°、64.6°、78.9°处出现的4个衍射峰,除强度稍有增强,其峰形和位置与未经处理秸秆纤维的衍射峰基本一致,表明微波处理没有改变纤维的结晶形态。FTIR光谱表明,微波处理样中未产生新的官能团,但分子间氢键及分子内氢键发生变化。微波作用未引起秸秆纤维化学结构的变化。     

α-取代-E-3,5-二羟基苯丙烯酸的合成及其抗炎活性

以3,5-二甲氧基苯甲醛为原料,经Perkin反应生成α-取代-E-3,5-二甲氧基苯丙烯酸,然后脱去芳甲醚的甲基合成了三个新的α-取代-E-3,5-二羟基苯丙烯酸(4a~4 c),其结构经1H NMR,IR和MS确证。应用二甲苯致小鼠耳肿胀模型评价4的抗炎活性,结果表明它们均有抗炎活性。其中4b与阳性对照药阿司匹林相比,表现出显著性差异(P0.05)。     

同位素内标超高效液相色谱-串联质谱法检测大鼠血清中丙烯酰胺和环氧丙酰胺

建立了检测大鼠血清中丙烯酰胺和环氧丙酰胺的超高效液相色谱-串联质谱法(UPLC-MS/MS).血清样品中加入乙腈沉淀蛋白质,超高速离心取上清液,离心浓缩后,采用ACQUITY UPLC T3 C18色谱柱(50 mm×2.1 mm, 1.7 μm),以0.1%甲酸溶液和甲醇为流动相进行梯度洗脱,经UPLC分离,电喷雾离子化四级杆串联质谱以正离子多反应监测方式(MRM)检测,用同位素内标法定量.丙烯酰胺和环氧丙酰胺在0.5～20.0 mg/L浓度范围内线性良好,相关系数r均大于0.999;检出限均为0.1 mg/L;在3个浓度水平(2.0, 8.0, 和15.0 mg/L)进行添加实验,样品的加标回收率分别为98.0%～108.3%和99.6%～106.7%;日内精密度(RSD)为0.54%～5.8%和1.1%～5.8%;每个样品测试时间仅为6 min.本方法测定大鼠血清中的丙烯酰胺和环氧丙酰胺操作简单快速, 重现性好, 灵敏度高.     

Temporal cleaning of a high-energy fiber-based ultrafast laser using cross-polarized wave generation

We report the use of cross-polarized wave generation to perform both pulse shortening and temporal cleaning of a high-energy ytterbium-doped fiber-based femtosecond laser system. The nonlinear processes allow both a highly efficient nonlinear conversion of 20% and a large compression ratio of 3.5, with inherently improved coherent and incoherent contrasts. This results in the generation of 37 μJ, 115 fs pulses at a repetition rate of 100 kHz with high temporal quality.     

Oxidation kinetics of thin copper films and wetting behaviour of copper and Organic Solderability Preservatives (OSP) with lead-free solder

The oxide formation on thin copper films deposited on Si wafer was studied by XPS, SEM and Sequential Electrochemical Reduction Analysis SERA. The surfaces were oxidized in air with a reflow oven as used in electronic assembly at temperatures of 100 °C, 155 °C, 200 °C, 230 °C and 260 °C. The SERA analyses detected only the formation of Cu₂O but the XPS analysis done for the calibration of the SERA equipment proved also the presence of a CuO layer smaller than 2 nm above the Cu₂O oxide. The oxide growth follows a power-law dependence on time within this temperature range and an activation energy of 33.1 kJ/mol was obtained. The wettability of these surfaces was also determined by measuring the contact angle between solder and copper substrate after the soldering process. A correlation between oxide thickness and wetting angle was established. It was found that the wetting is acceptable only when the oxide thickness is smaller than 16 nm. An activation energy of 27 kJ/mol was acquired for the spreading of lead free solder on oxidized copper surfaces.From wetting tests on copper surfaces protected by Organic Solderability Preservatives (OSP), it was possible to calculate the activation energy for the thermal decomposition of these protective layers.     

The effect of solute on ultrasonic grain refinement of magnesium alloys

An experimental study has been conducted to assess the structural refinement of magnesium and its alloys by ultrasonic irradiation during solidification. It is shown that (i) ultrasonic irradiation leads to significant refinement only in the presence of adequate solute, which is alloy dependent; (ii) the attendant grain density increases linearly with increase in solute content at a given irradiation level; (iii) increasing the solute content at a low irradiation level above the cavitation threshold is more effective than substantially increasing the irradiation intensity; and (iv) the difference in the grain size between two ultrasonicated magnesium alloys is mainly determined by the solute content rather than the irradiation intensity. In view of these, the effect of ultrasonic irradiation on solute redistribution in a solidifying magnesium alloy seems rather limited even at a substantial intensity level such as 1700 W cm⁻². The implications of these findings are discussed and a mechanism is proposed to account for the experimental observations.