Difference between canonical and grand canonical ensembles in discrete lattice gas models

We calculate the site occupation probabilities of one-dimensional lattice gas models within the canonical and grand canonical ensembles. The appearing differences do not vanish if we increase the system size keeping the site energies discrete. In this way one can explain the surprising numerical results of Barszczak and Kutner. This effect in the single-site occupation number disappears in higher dimensions.     

Bragg diffraction of light in a restricted homogeneous system of tunnel-coupled waveguides

A system of tunnel-coupled rectilinear waveguides is studied. The dependence of the number of modes in this system on the number of waveguides N, the distance between the waveguides, and the number of modes in a separate waveguide is considered. It is shown that the modes of the m = N and N + 1 orders in such a system are Bragg modes; i.e., the angle between the direction of their propagation and the system axis is close to the Bragg angle. The effective refractive indices n ^* of these modes change stepwise. The step size Δn ^* is found to be dependent on the distance s between the waveguides and on the number of modes in a separate waveguide. A system of single-mode waveguides with the number of guided modes M = 34 < N = 50 is studied experimentally. It is shown that the Bragg modes of the system lie among the leakage modes of the system and have rather low losses. It is demonstrated that the localization of the Bragg modes among the leakage modes may be favorable for their selection upon light generation.     

NMR protocol for on-line Brix determination

Water suppression by diffusive attenuation was used to measure Brix in intact cellular tissue of apple and strawberry. Given the signal-to-noise ratio, the correlation for apple was established without repeated acquisition, so this protocol should also be useful for rapid, on-line measurements at low spectrometer frequencies. Water suppression by theT ₁-Null method fails with cellular tissue because of the considerable variation in the longitudinal relaxation times of vacuolar and cytoplasmic water.     

Characterization of surface deformation around Vickers indentations in InGaAsP epilayers on InP substrate

The deformation surrounding Vickers indentations on InGaAsP/InP epilayers have been studied in detail. The surface topography was characterized by using atomic force microscopy (AFM). The material pile-up and sink-in regions around the indentation impression was observed for the quaternary InGaAsP/InP epilayers. The sectional analysis mode of the AFM shows the depth profile at the indented region. Microindentation studies were carried out for different atomic fraction of the quaternary InGaAsP/InP compound semiconductor alloys. The microhardness values of InGaAsP/InP epilayers were found to be in the range of 5.08 and 5.73 GPa. These results show that the hardness value of the quaternary alloy drastically increases as the composition of As was increased by 0.01 atomic fraction and when the phosphorous concentration decreases from 0.4 to 0.38. The reason may be that the increase in As concentration hardens the lattice when phosphorous concentration was less and hardness decreases when phosphorous was increased.     

The design of the main accelerator for a pulsed positron beam

The pulsed positron beam at the Helsinki University of Technology is designed for the end energy of 3-30 keV and grounded target. This is achieved with a constant voltage acceleration followed by an adjustable deceleration. In the design of this accelerator-decelerator the possibility for electrical breakdowns and partial discharges must be eliminated.For designing the electrode and insulator structures for accelerator-decelerator configuration electric field simulations were carried out with the finite element analysis program. In this paper we present the design of the accelerator-decelerator and the results of the electric field simulations. The results of high voltage tests will also be presented and compared with the simulations.     

Effect of the paste molding pressure on the mechanical strength of an iron oxide catalyst in the dehydrogenation of methylbutenes

The effect of the paste molding pressure on the physicomechanical and texture characteristics of catalysts was studied. An indirect criterion is suggested to evaluate the molding pressure in industrial extruders, whose optimal value ensures good physicomechanical properties of the catalysts and kinetic control over the catalyzed reaction. The results obtained were verified in paste molding on various industrial extruders, and this enabled the optimal choice of the molding equipment.     

Finitely additive integration and local integration with respect to upper integrals

Summary We study the integration theory for general integral metrics when restricted to upper integrals q, finding improvements in the relation between the classes of the q-integrable and the q_l-integrable functions. We give new results and notions which lead to the desirable characterizations of q-integrable functions as q_l-integrable f with q(|f|) < ∞, and of q_l-integrable functions via the integrability of their upper truncations, under natural conditions which are fulfilled in most finitely additive integration theories.     

Critical phenomena in FINEMET alloy

The Fe_73.5Cu₁Nb₃Si_13.5B₉ FINEMET alloy has been prepared by the rapid solidification technique. The critical behaviour of this alloy in the amorphous as well as in its nanocrystalline states has been studied near their respective Curie temperatures. From the values of the critical exponents one can conclude that the alloy behaves like a 3D Heisenberg ferromagnet in the amorphous and nanocrystalline states. But there exists a slight increase in the value of β for the alloy annealed at 823 K (the nanocrystalline state) as observed in most of the amorphous alloys.