Preparation and characterization of rigid poly(vinyl chloride)/MMT nanocomposites. II. XRD,morphological and mechanical characteristics

A Haake torque rheometer equipped with an internal mixer is used to study the influence of the amount of sodium montmorillonite (Na⁺‐MMT) and organically modified MMT (O‐MMT) on X‐ray diffraction (XRD), morphology, and mechanical characteristics of rigid poly (vinyl chloride) (PVC)/Na⁺‐MMT and PVC/O‐MMT nanocomposites, respectively. Results of XRD and transmission electron microscopy (TEM) indicate that MMT is partially encapsulated and intercalated in the rigid PVC/Na⁺‐MMT nanocomposites. However, results of XRD and TEM show MMT is partially intercalated and exfoliated in the rigid PVC/O‐MMT nanocomposites. Tensile strength, yield strength, and elongation at break of the rigid PVC/MMT nanocomposites were improved simultaneously with adding 1–3 wt % Na⁺‐MMT or O‐MMT with respect to that of pristine PVC. However, the addition of Na⁺‐MMT or O‐MMT should be kept as not more than 3 wt % to optimize the mechanical properties and the processing stability of the rigid PVC/MMT nanocomposites. SEM micrographs of the fractured surfaces of the rigid PVC/Na⁺‐MMT and PVC/O‐MMT nanocomposites both before and after tensile tests were also illustrated and compared. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2145–2154, 2006     

Measurement and prediction of solubilities and diffusion coefficients of carbon dioxide in starch–water mixtures at elevated pressures

The solubility and diffusion coefficient of carbon dioxide in intermediate‐moisture starch–water mixtures were determined both experimentally and theoretically at elevated pressures up to 16 MPa at 50 °C. A high‐pressure decay sorption system was assembled to measure the equilibrium CO₂ mass uptake by the starch–water system. The experimentally measured solubilities accounted for the estimated swollen volume by Sanchez–Lacombe equation of state (S‐L EOS) were found to increase almost linearly with pressure, yielding 4.0 g CO₂/g starch–water system at 16 MPa. Moreover, CO₂ solubilities above 5 MPa displayed a solubility increase, which was not contributed by the water fraction in the starch–water mixture. The solubilities, however, showed no dependence on the degree of gelatinization (DG) of starch. The diffusion coefficient of CO₂ was found to increase with concentration of dissolved CO₂, which is pressure‐dependent, and decrease with increasing DG in the range of 50–100%. A free‐volume‐based diffusion model proposed by Areerat was employed to predict the CO₂ diffusivity in terms of pressure, temperature, and the concentration of dissolved CO₂. S‐L EOS was once more used to determine the specific free volume of the mixture system. The predicted diffusion coefficients showed to correlate well with the measured values for all starch–water mixtures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 607–621, 2006     

Metallocene copolymers of propene and 1‐hexene: The influence of the comonomer content and thermal history on the structure and mechanical properties

The relationships between the structure and properties have been established for copolymers of propylene and 1‐hexene synthesized with an isotactic metallocene catalyst system. The most important factor affecting the structure and properties of these copolymers is the comonomer content. The thermal treatment, that is, the rate of cooling from the melt, is also important. These factors affect the thermal properties, the degree of crystallinity, and therefore the structural parameters and the viscoelastic behavior. A slow cooling from the melt favors the formation of the γ phase instead of the α modification. Regarding the viscoelastic behavior, the β relaxation, associated with the glass‐transition temperature, is shifted to lower temperatures and its intensity is increased as the 1‐hexene content raises. The microhardness values are correlated with those of the storage modulus deduced from dynamic mechanical thermal analysis curves, and good linear relations have been obtained between these parameters. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1253–1267, 2006     

Characterization and electrical properties of polypyrrole/multiwalled carbon nanotube composites synthesized by in situ chemical oxidative polymerization

This study describes the preparation of polypyrrole (PPy)/multiwalled carbon nanotube (MWNT) composites by in situ chemical oxidative polymerization. Various ratios of MWNTs, which served as hard templates, were first dispersed in aqueous solutions with the surfactant cetyltrimethylammonium bromide to form micelle/MWNT templates and overcome the difficulty of MWNTs dispersing into insoluble solutions of pyrrole monomer, and PPy was then synthesized via in situ chemical oxidative polymerization on the surface of the templates. Raman spectroscopy, Fourier transform infrared (FTIR), field‐emission scanning electron microscopy (FESEM), and high‐resolution transmission electron microscopy (HRTEM) were used to characterize the structure and morphology of the fabricated composites. Structural analysis using FESEM and HRTEM showed that the PPy/MWNT composites were core (MWNT)–shell (PPy) tubular structures. Raman and FTIR spectra of the composites were almost identical to those of PPy, supporting the idea that MWNTs served as the core in the formation of a coaxial nanostructure for the composites. The conductivities of these PPy/MWNT composites were about 150% higher than those of PPy without MWNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1413–1418, 2006     

A highly sensitive and rapid assay for protein determination in human urine and penicillin using a Rayleigh light-scattering technique with benzeneazo-8-acetylamino-1-naphthol-3,6-disulfonic acid sodium salt.

A simple and sensitive method was conducted for the determination of trace amounts of proteins with benzeneazo-8-acetylamino-1-naphthol-3,6-disulfonic acid sodium salt (azophloxine, AP) using a Rayleigh light-scattering (RLS) technique. At pH 2.60 and in the presence of an emulsifier OP microemulsion, the RLS of AP can be greatly enhanced by proteins, owing to the interaction between AP and protein. The enhanced intensity is proportional to the concentration of proteins. Four proteins, including bovine serum albumin (BSA), human serum albumin (HSA), lysozyme (Lys) and gamma globulin (gamma-G) have been tested. For example, the linear range of BSA was 0 - 0.06 microg mL(-1) with detection limits of 2.38 ng mL(-1). The method was applied to the analysis of protein in human urine and penicillin samples with satisfactory results. The relative standard deviation was in all instances less than 4.0%, and the recovery was in the range of 97.5 - 104%.     

Novel photoswitching dithienylethenes with ferrocene units

Two novel dithienylethenes with ferrocene units were synthesized by Wittig reaction. The structure of 2a has been established by X‐ray diffraction studies. They could reversibly interconvert between two thermally stable forms, an open and a closed one, using light of different wavelengths as triggers. Copyright © 2006 John Wiley & Sons, Ltd.     

Retracted: Determination of scutellarin isomer,a predominant metabolite of scutellarin,in human plasma by HPLC/tandem mass spectrometry and its application to a pharmacokinetic study in Chinese healthy volunteers

Retraction: The following article from Biomedical Chromatography, “Determination of scutellarin isomer, a predominant metabolite of scutellarin, in human plasma by HPLC/tandem mass spectrometry and its application to the pharmacokinetic study in Chinese healthy volunteers” by Chun‐hua Xia, Yu‐qing Xiong, and Guang‐ji Wang, published online on 21 June 2007 in Wiley Interscience (www.interscience.wiley.com/journal/bmc), has been retracted at the authors' request.     

合成丙交酯中微量水分分析

合成丙交酯中微量水分分析徐溢，柳胜春（重庆大学化工学院分析教研室６３００４４）关键词丙交酯，微量水，定量分析丙交酯是人工合成骨材料聚乳酸的合成中间体，其性能决定着合成产品的品质，要获得高质量的合成材料，对中间体的分析和监测十分重要。一般要求丙交酯中间...     

4-Amino-imidazole durchThorpe-Cyclisierung

The alkylation of arylaminomethylenecyanamides1 or cyano-imidothiocarbamates2 with -halogen carbonyl compounds followed by base catalysed cyclization yields substituted 4-amino-imidazoles4. Imidazo[4,5-d]pyrimidones5, 6 and imidazo[4,5-b]pyridines7 can be obtained from4.     

The electrocapillarity of polyacrylates

Summary The electrocapillary properties of polyacrylic acid have been studied by two methods. Exploratory measurements have been made of the effect of the polymer on the differential capacity of a mercury drop in 0.1 m sodium perchlorate. They showed that the polymer was strongly adsorbed over a wide range of potentials but that it did not appear to form a monolayer. The surface excess of polymer obtained from drop weight data showed a maximum at very low concentrations and then a decline at higher concentrations. The bulk of the work was carried out by making surface tension measurements, using a sessile mercury drop, in solutions of a fraction of polyacrylic acid (mol. wt. 7.02×10⁴) in potassium chloride at 0.01, 0.1, 0.2, and 0.5 m at 25°C.The data have been used to evaluate the surface excesses of the polymer and of the inorganic ions. The distribution of K⁺ and Cl^– in the electrical double layer and the contact adsorption of Cl^– on the mercury were very little affected by the presence of the polymer. The surface excess of polymer was always found to be greatest at low concentrations, to decrease steeply at first as the concentration was increased and then to decrease more slowly at higher concentrations.Possible explanations of this behaviour are discussed and it is concluded that the rapid decrease is a consequence of molecular weight dispersion and the stronger adsorption of high molecular weight polymer. The slow decrease in surface excess at higher concentrations may be a result of configurational changes of the polymer molecules.Surface pressure data show that, despite this decrease in the surface excess, the surface coverage reaches a high level at very low polymer concentrations and then continues to increase slowly as the concentration of polymer is increased. This apparent contradiction is due to changes in configuration of the adsorbed polymer molecules. At higher bulk concentrations the chain configurations are more compact and each adsorbed molecule makes more contacts with and so occupies a greater area of the mercury surface than at low concentrations.The conclusion is reached that the surface excess of polymer is mostly contained in a layer probably more than 1000 Å thick. It consists of a concentrated and entangled mass of polymer chains. Relatively few of these chains are in contact with the mercury at any istant. The concentration in this surface layer decreases steadily with increasing distance from the mercury surface and it merges without discontinuity into the bulk solution.With 10 figures in 22 details