废轮胎热解炭的分析及其活化特性的研究

用常规分析方法分析了废轮胎热解炭的成分和性质，用X射线能谱分析法、压汞法、N2吸附法等测定了热解炭的孔隙结构特性，并用CO2、含2％氧气的氮气流和水蒸气等活化气体对热解炭进行活化方面的研究。结果表明，热解炭灰分和硫含量比较高；两种不同粒径热解炭的比孔容积均在r≈25 nm处有最大值；在相同活化时间和活化剂流速下，温度越高，活化炭烧失率越大，比表面积也越大；在一定温度和活化剂流速下，烧失率和比表面积随着活化时间的增加而增大；对所有试验工况，烧失率越大，活化炭比表面积也越大。总体上水蒸气活化炭与CO2的活化效果较好，而含2％O2的氮气流活化的效果则次之。活化炭与商业活性炭的比较显示，前者具有较发达的孔隙结构，在进行大分子物质吸附时，具有替代商业活性炭的潜力。     

Validating methods for measuring delta18O and delta13C in otoliths from freshwater fish

The ability of the phosphoric acid digestion technique to extract carbon dioxide from biogenic carbonates and reliably reproduce delta(18)O and delta(13)C signatures from standard reference materials (NBS-18, NBS-19) was tested and shown to produce accurate, unbiased measurements of non-biologic materials. The effects of roasting preparation methods commonly reported when analyzing biogenic carbonates were also tested in a series of experiments using reference standards and otoliths obtained from aquacultured Arctic charr and rainbow trout. Roasting had no effect on the isotope measurement of reference standards. No significant differences between mean oxygen isotope signatures from paired experiments with roasted and non-roasted fish otoliths were found. However, otolith oxygen isotope measurements were significantly enriched in comparison to rearing water-based measurements for both species. Agreement between expected isotopic equilibrium and measured otolith delta(18)O values varied as a function of roasting temperature and between species. Criteria for the selection of appropriate roasting temperatures are suggested and favour 350 degrees C in freshwater fish where unbiased estimates of average rearing water temperatures and known differences in rearing temperatures were obtained. Carbon isotopic disequilibria were observed for both species. A mixing model analysis established differences in the percentage of metabolically derived carbon in studied otoliths, with Arctic charr deriving a greater proportion of otolith delta(13)C from metabolism as a result of higher metabolic rates.     

On the Banach space isomorphism type of AF C*-algebras and their triangular subalgebras

It is shown that all the approximately finite dimensional C^*-algebras which are not of Type I are isomorphic as Banach spaces. This generalizes the matroid case given previously by Arazy. Analogous results are obtained for various families of triangular subalgebras of AF C^*-algebras. In addition the classification of various continua of Type I AF C^*-algebras is discussed.     

Protein interactions with model chromatographic stationary phases constructed using self-assembled monolayers

Model surfaces representative of chromatographic stationary phases were developed by immobilising an homologous series (C2-C18) of n-alkylthiols, mixed monolayers of C4/C18 and thioalkanes with alcohol, carboxylic acid, amino and sulphonic acid terminal groups onto a flat, silver-coated glass surface using self-assembled monolayer (SAM) chemistry. The processes of adsorption and desorption of serum albumins onto the monolayer surfaces was monitored in real-time using surface plasmon resonance (SPR). Alkyl-terminated SAMs all showed a strong adsorption of bovine serum albumin which was largely independent of alkyl chain length, the ratio of mixed C4/C18 SAMs or the solution pH/ionic strength. The adsorption of human serum albumin to carboxylic and amine terminated SAMs was shown to be predominantly via non-electrostatic interactions (hydrophobic or hydrogen bonding). However, sulphonic acid terminated SAMs showed almost exclusively electrostatic interactions with human serum albumin. This preliminary work using self-assembled monolayer chemistry confirms the usefulness of well characterised SAMs surfaces for investigating protein adsorption and desorption onto/from model chromatography surfaces and gives some guidance for selecting appropriate functionalities to develop better surfaces for chromatography and electrophoresis.     

Reactions of the heavier group 14 element alkyne analogues Ar'EEAr' (Ar' = C6H3-2,6(C6H3-2,6-Pri2)2; E = Ge, Sn) with unsaturated molecules: probing the character of the EE multiple bonds

Reactions of the alkyne analogues Ar'EEAr' (Ar' = C6H3-2,6(C6H3-2,6-Pr(i)2)2; E = Ge (1); Sn (2)) with unsaturated molecules are described. Reaction of 1 and 2 with azobenzene afforded the new hydrazine derivatives Ar'E{(Ph)NN(Ph)}EAr' (E = Ge (3); Sn (4)). Treatment of 1 with Me3SiN3 gave the cyclic singlet diradicaloid Ar'Ge{mu2-(NSiMe3)}2GeAr' (5), whereas 2 afforded the monoimide bridged Ar'Sn{mu2-N(SiMe3)}SnAr' (6). Reaction of 1 with t-BuNC or PhCN yielded the adduct Ar'GeGe(CNBu(t))Ar' (7) or the ring compound (8). In contrast, the tin compound 2 did not react with either t-BuNC or PhCN. Treatment of 1 with N2CH(SiMe3) generated Ar'Ge{mu2-CH(SiMe3)}{mu2:eta2-N2CH(SiMe3)}{mu2-N2CH(SiMe3)}GeAr' (9) which contains ligands in three different bridging modes and no Ge-Ge bonding. Reaction of 1 with an excess of N(2)O gave a germanium peroxo species Ar'(HO)Ge(mu2-O)(mu2:eta2-O2)Ge(OH)Ar' (10) which features a ring. Oxidation of 1 by tetracyanoethylene (TCNE) led to cleavage of the Ge-Ge bond and formation of a large multiring system of formula Ar'Ge3+{(TCNE)2-}3{(GeAr')+}3. The digermyne 1 also reacted with 1 equiv of PhCPh to give the 1,2-digermacyclobutadiene 12, which has a ring, and with Me(3)SiCCH or PhCC-CCPh to activate a flanking C6H3-2,6-Pr(i)2 ring and give the tricyclic products 13 and 14. The "distannyne" 2 did not react with these acetylenes. Overall, the experiments showed that 1 is highly reactive toward unsaturated molecules, whereas the corresponding tin congener 2 is much less reactive. A possible explanation of the reactivity differences in terms of the extent of the singlet diradical character of the Ge-Ge and Sn-Sn bonds is discussed.     

New Routes to Synthetically Useful, Sterically Encumbered Arylaluminum Halides and Hydride Halides

The synthesis and structural characterization of the compounds MesAlCl(2)(THF) (1), MesAlCl(2) (2), MesAl(H)Cl(THF) (3a), MesAl(H)Cl (4a), and (MesAlH(2))(2) (5) (Mes = 2,4,6-t-Bu(3)C(6)H(2)(-)) are described as well as those for two compounds 3b and 4b that are analogs of 3a and 4a but have H:Cl ratios that are less than 1:1. All compounds were characterized by (1)H, (13)C NMR, and IR spectroscopy, and 1, 2, 3a, and 4b were additionally characterized by X-ray crystallography. Compound 1 is best synthesized by the reaction of [(THF)(2)LiH(3)AlMes](2) (6) with 6 equiv of Me(3)SiCl. A more conventional route involving the addition of (THF)(2)LiMes to 2 equiv of AlCl(3) in toluene usually affords a mixture of 1 and AlCl(3).THF. Recrystallization of 1 from n-hexane results in a species that has less than 1 equiv of THF per MesAlCl(2). The THF free complex 2 may be obtained in quantitative yield by heating 1 for 20 min at 90 degrees C under reduced pressure. Compound 3a may be obtained by treating a 1:1 mixture of MesLi(THF)(2) and LiAlH(4) with 2 equiv of Me(3)SiCl or by the addition of slightly less than 4 equiv of Me(3)SiCl to 6. The THF can be removed from 3a by sublimation to give 4a. The related compounds 3b and 4b, which display an aluminum-bound H:Cl ratio that is deficient in H, can be obtained by reactions with slightly more than 2 equiv of Me(3)SiCl. Crystal data at 130 K with Cu Kalpha (lambda = 1.541 78 ?) radiation: 1, C(22)H(37)AlCl(2)O, a = 11.889(3) ?, b = 9.992(3) ?, c = 19.704(5) ?, orthorhombic, space group Pca2(1), Z = 4, R = 0.068 for 1556 (I > 2sigma(I)) data; 2, C(18)H(29)AlCl(2), a = 12.147(5) ?, b = 18.042(6) ?, c = 17.771(7) ?, beta = 95.77(3) degrees, monoclinic, space group P2(1)/n,Z = 8, R = 0.032 for 4610 (I > 2sigma(I)) data; 3a, C(22)H(38)AlClO, a = 16.887(7) ?, b = 16.333(6) ?, c = 8.739(3) ?, beta = 101.41(3) degrees, monoclinic, space group P2(1)/c, Z = 4, R = 0.073 for 2752 (I > 2sigma(I)) data; 4b, C(18)H(29.64)AlCl(1.36), a = 12.077(3) ?, b = 17.920(3) ?, c = 17.634(5) ?; beta = 95.21(2) ?, monoclinic, space group P2(1)/n,Z = 8, R = 0.070 for 4261 (I > 2sigma(I)) data.     

Synthesis and characterization of HC[C(Me)N(C(6)H(3)-2,6-i-Pr(2))](2)MX(2) (M = Al, X = Cl, I; M = Ga, In, X = Me, Cl, I): sterically encumbered beta-diketiminate group 13 metal derivatives

A series of group 13 metal complexes featuring the beta-diketiminate ligand [[(C(6)H(3)-2,6-i-Pr(2))NC(Me)](2)CH](-) (i.e., [Dipp(2)nacnac](-), Dipp = C(6)H(3)-2,6-i-Pr(2)) have been prepared and spectroscopically and structurally characterized. The chloride derivatives Dipp(2)nacnacMCl(2) (M = Al (3), Ga (5), In (8)) were isolated in good yield by the reaction of 1 equiv of Dipp(2)nacnacLi.Et(2)O (2) and the respective metal halides. The iodide derivatives Dipp(2)nacnacMI(2) (M = Al (4), Ga (6), In (9)), which are useful for reduction to afford M(I) species, were made by a variety of routes. Thus, 4 was obtained by treatment of the previously reported Dipp(2)nacnacAlMe(2) with I(2), whereas the gallium analogue 6 was obtained as a product of the reaction of "GaI" with Dipp(2)nacnacLi.Et(2)O, and 9 was obtained by direct reaction of InI(3) and the lithium salt. The methyl derivatives Dipp(2)nacnacMMe(2) (M = Ga (7), In (10)), which are analogous to the previously reported Dipp(2)nacnacAlMe(2), were synthesized by the reaction of GaMe(3) with Dipp(2)nacnacH (1) or by reaction of the indium chloride derivative 8 with 2 equiv of MeMgBr in diethyl ether. The compounds 3-10 exist as colorless, air- and moisture-sensitive crystalline solids. Their X-ray crystal structures feature nearly planar C(3)N(2) arrays in the Dipp(2)nacnac ligand backbone with short C-C and C-N distances that are consistent with a delocalized structure. However, there are large dihedral angles between the C(3)N(2) plane and the N(2)M metal coordination plane which have been attributed mainly to steric effects. The relatively short M-N distances are consistent with the coordination numbers of the metals and the normal/dative character of the nitrogen ligands. The compounds were also characterized by (1)H and (13)C NMR spectroscopy. (1)H NMR data for 7 revealed equivalent methyl groups whereas the spectrum of 10 displayed two In-Me signals which indicated that ring wagging was slow on the (1)H NMR time scale.     

Spontaneous generation of stable pnictinyl radicals from "jack-in-the-box" dipnictines: a solid-state, gas-phase, and theoretical investigation of the origins of steric stabilization

The molecular structures of the stable phosphinyl and arsinyl radicals, .PnR(2) [Pn = P (2); As (4); R = CH(SiMe(3))(2)], have been determined by gas-phase electron diffraction (GED) in conjunction with ab initio molecular orbital calculations. The X-ray crystal structures of the corresponding dipnictines, the "dimers", R(2)PnPnR(2) [Pn = P (1), As (3)], and the chloro derivatives R(2)PnCl [Pn = P (5), As (6)] have also been determined. Collectively, these structural investigations demonstrate that large distortions of the ligands attached to Pn occur when the pnictinyl radicals unite to form the corresponding dipnictine dimers. Principally, it is the shape and flexibility of the CH(SiMe(3))(2) ligands that permit the formation of the P-P and As-As bonds in 1and 3, respectively. However, theoretical studies indicate that in the process of pnictinyl radical dimerization to form 1 and 3, both molecules accumulate substantial amounts of potential energy and are thus primed to spring apart upon release from the solid state by melting, dissolution, or evaporation. The insights gleaned from these unusual systems have permitted a deeper understanding of the functioning of sterically demanding substituents.