Measurement of meropenem concentration in different human biological fluids by ultra-performance liquid chromatography-tandem mass spectrometry

Meropenem is a broad-spectrum antibiotic, often used for the empirical treatment of infections in critically ill patients with acute kidney injury. Meropenem has clinically insignificant protein binding and, as a carbapenem antibiotic, shows time-dependent bacterial killing, meaning that the unbound or free antibiotic concentration in blood should be maintained above the minimal inhibitory concentration of the pathogen for at least 40 % of the dosing interval. We developed and validated simple chromatographic methods by ultra-performance liquid chromatography-tandem mass spectrometry to measure plasma, filtrate-dialysate, and urine concentrations of meropenem. Chromatographic separation was achieved using an Acquity^® UPLC^® BEH^TM (2.1?×?100 mm id, 1.7 μm) reverse-phase C₁₈ column, with a water/acetonitrile linear gradient containing 0.1 % formic acid at a 0.4-mL/min flow rate. Meropenem and its internal standard (ertapenem) were detected by electrospray ionization mass spectrometry in positive ion multiple reaction monitoring mode. The limits of quantification were 0.27, 0.24, and 1.22 mg/L, and linearity was observed between 0.27–150, 0.24–150, and 1.22–2,000 mg/L for plasma, filtrate-dialysate, and urine samples, respectively. Coefficients of variation and relative biases were less than 13.5 and 8.0 % for all biological fluids. Recovery values were greater than 68.3 %. Evaluation of the matrix effect showed ion suppression for meropenem and ertapenem. No carry-over was observed. The validated methods are useful for both therapeutic drug monitoring and pharmacokinetic studies. It could be applied to daily clinical laboratory practice to measure the concentration of meropenem in plasma, filtrate-dialysate, and urine.

Water-induced (nano) organization in poly(ethyl acrylate-co-hydroxyethyl acrylate) networks

The conformational changes in poly(ethyl acrylate-co-hydroxyethyl acrylate), P(EA-co-HEA) chains, which constitute a copolymer network hydrogel, induced by the presence of water are investigated by different experimental techniques and compared with the behaviour of the corresponding xerogel. The mechanical relaxation spectrum shows the presence of a new water-induced relaxation, the water content dependence of the glass transition is measured by DSC, and the dielectric relaxation assesses the effect of water for the lower concentrations. Hydrophilic and hydrophobic monomeric units in the P(EA-co-HEA) network are able to aggregate to form two separated (nano)phases in the presence of water due to hydrophobic interaction. Phase separation takes place when the water content of the sample is higher than a critical value estimated as two water molecules per -OH group in the copolymer chain. The existence of the hydrophobic domains is detected by their glass transition being nearly independent on the water content of the sample. Phase separation is also clearly revealed by phase angle measurements in AFM experiments.     

Effect of micelle composition on the formation of surfactant-templated polymer films

Surfactant-templated polymer films prepared from polyethylenimine (PEI), cetyltrimethylammonium bromide (CTAB), and octaethylene glycol monohexadecyl ether (C(16)E(8)) were examined and the effect of increasing the percentage of nonionic surfactant in the micelles measured using both surface and bulk-sensitive techniques. It was found that there is a strong interaction between CTAB and C(16)E(8), although no interaction between the C(16)E(8) and PEI was observed. Generally, increasing the percentage of C(16)E(8) in the micelles decreases both the thickness and degree of order in the films; however, it was observed, depending on the conditions, that films could still be formed with as little as 20% cationic surfactant. Experiments on the CTAB/Brij56/PEI system were also performed and these indicate that it is similar to the CTAB/C(16)E(8)/PEI system.     

Leachability and analytical speciation of antimony in coal fly ash

A new procedure was described with multiwalled carbon nanotubes as solid phase extraction packing material for the trace analysis of nicosulfuron, thifensulfuron and metsulfuron-methyl in water samples. The possible parameters influencing the enrichment were optimized and the optimal conditions were as followed: eluent, sample pH, flow rate and sample volume were acetonitrile containing 1% acetic acid, pH 3, 8 mL min⁻¹ and 500 mL, respectively. Under the optimal chromatographic separation and SPE conditions, the linear range, detection limit (S/N = 3) and precision (R.S.D., n = 6) were 0.04-40 ng mL⁻¹, 6.8 ng L⁻¹ and 2.5% for nicosulfuron, 0.04-40 ng mL⁻¹, 11.2 ng L⁻¹ and 5.4% for thifensulfuron, 0.02-20 ng mL⁻¹, 5.9 ng L⁻¹, 2.1% for metsulfuron-methyl, respectively. The established method was well employed to determine nicosulfuron, thifensulfuron and metsulfuron-methyl in tap water, seawater, reservoir water and well water samples, and satisfactory results were obtained, the spiked recoveries in the range of 87.2-100.7%, 96.5-105.6% and 83.7-111.1% for them each, respectively.