Development of a new sample pre-treatment procedure based on pressurized liquid extraction for the determination of metals in edible seaweed

A new, simple, fast and automated method based on acetic acid-pressurized liquid extraction (PLE) has been developed for the simultaneous extraction of major and trace elements (As, Ca, Cd, Co, Cr, K, Mg, Mn, Na, Pb, Sr and Zn) from edible seaweeds. The target elements have been simultaneously determined by inductively coupled plasma-optical emission spectrometry (ICP-OES). The influence of several extraction parameters (e.g. acetic acid concentration, extraction temperature, extraction time, pressure, number of cycles, particle size and diatomaceous earth (DE) mass/sample mass ratio) on the efficiency of metal leaching has been evaluated. The results showed that metal extraction efficiency depends on the mass ratio of the dispersing agent mass and the sample. The optimized procedure consisted of the following conditions: acetic acid (0.75 M) as an extracting solution, 5 min of extraction time, one extraction cycle at room temperature at a pressure of 10.3 MPa and addition of a dispersing agent (at a ratio of 5:1 over the sample mass). The leaching procedure was completed after 7 min (5 min extraction time plus 1 min purge time plus 1 min end relief time). Limits of detection and quantification and repeatability of the over all procedure have been assessed. Method validation was performed analysing two seaweed reference materials (NIES-03 Chlorella Kessleri and NIES-09 Sargasso). The developed extraction method has been applied to red (Dulse and Nori), green (Sea Lettuce) and brown (Kombu, Wakame and Sea Spaghetti) edible seaweeds.     

Crystal structures of poly(aryl ether) dendrons with palladium scorpionate complexes at their focal point

Novel palladium(II) complexes with bis(pyrazol-1-yl)methane ligands at the focal point of G0-G3 poly(aryl ether) Fréchet-type dendrons are reported. The molecular structures of the metallodendrimer series G0, G1, and G2 [(dend)CH(3,5-Me2pz)2(PdCl2)] have been determined by X-ray diffraction methods. The three structures show a similar three-dimensional organization of the metal complex, which is progressively engulfed by the branches with increasing dendrimer generation.     

Pure and mixed films of a nitrostilbene derivative at the air-water interface, Langmuir-Blodgett multilayer fabrication, and optical characterization

This paper reports the preparation and characterization of pure Langmuir and Langmuir-Blodgett (LB) films of a stilbene derivative containing two alkyl chains, namely 4-dioctadecylamino-4'-nitrostilbene. Mixed films incorporating docosanoic acid and the stilbene derivative are also studied. Brewster angle microscopy (BAM) analysis has revealed the existence of randomly oriented three-dimensional (3D) aggregates, spontaneously formed immediately after the spreading process of the stilbene derivative onto the water surface. These 3D aggregates coexist with a Langmuir film that shows the typical gas, liquid, and solid-like phases in the surface pressure and surface potential vs area per molecule isotherms, indicative of an average preferential orientation of the stilbene compound at the air-water interface, and a gradual molecular arrangement into a defined structure upon compression. A blue shift of 55 nm of the reflection spectrum of the Langmuir film with respect to the spectrum of a chloroform solution of the nitrostilbene indicates that two-dimensional (2D) H-aggregates are formed at the air-water interface. The monolayers are transferred undisturbed onto solid substrates with atomic force microscopy (AFM) revealing that the one layer LB films are constituted by a monolayer of the stilbene derivative together with some 3D aggregates. When the nitrostilbene compound is blended with docosanoic acid, the 3D aggregation is avoided in the Langmuir and Langmuir-Blodgett films, but does not limit the formation of 2D H-aggregates, desirable for second-order nonlinear optical response in the blue domain. The AFM images of the mixed LB films show that they are formed by a docosanoic acid monolayer and, on the top of it, a bilayer of the stilbene derivative.     

Synthesis and characterization of complexes containing Ti-O-Si moieties. Catalytic activity in olefin epoxidation

Reaction of [Cp*TiMe3] with O(SiPh2OH)2 yields the titanium siloxide derivative [Cp*TiMe{(OSiPh2)2O}]. Complex reacts with H2O to yield the corresponding oxo-titanium derivative [(Cp*Ti{(OSiPh2)2O})2(micro-O)]. The molecular structure of complex has been established by X-ray diffraction. Complex reacts with triphenylsilanol to give the asymmetric titanium siloxide [Cp*Ti(OSiPh3){(OSiPh2)2O}]. Treatment of the dinuclear titanium compound [(Cp*TiCl2)2(micro-O)] with an equimolar amount of O(SiPh2OH)2 yields complex [(Cp*TiCl)2{micro-(OSiPh2)2O}(micro-O)] in which the disiloxide moiety is bridging two titanium atoms. The structure of has been determined by X-ray diffraction. Reaction of [Cp*TiMe3] with HOSiPh3 yields the titanium triphenylsiloxide [Cp*TiMe2(OSiPh3)]. Complex reacts with water to yield [{Cp*TiMe(OSiPh3)}2(micro-O)]. The triflate compound [Cp*Ti(OSiPh3)2(OTf)] can be prepared by reaction of with HOTf and triphenylsilanol. We have tested the catalytic activity of some of the complexes in the epoxidation of cyclohexene.     

Total synthesis of the putative structure of stemonidine: the definitive proof of misassignment

[structure: see text] The total synthesis of the putative structure of the Stemona alkaloid stemonidine has been completed. The key transformations include a 1,3-dipolar cycloaddition of a chiral nitrone derived from (S)-prolinol and a spirolactonization process involving the generation of the critical stereocenter. The NMR data of the synthetic material do not match those reported for the natural product. It is concluded that the structure assigned to stemonidine is incorrect, and it must be reassigned as stemospironine.     

Part per trillion determination of atrazine in natural water samples by a surface plasmon resonance immunosensor

A new immunoassay for continuously monitoring atrazine in water has been developed. It uses a portable biosensor platform based on surface plasmon resonance (SPR) technology. This immunoassay is based on the binding inhibition format with purified polyclonal antibodies, with the analyte derivative covalently immobilized on a gold sensor surface. An alkanethiol self-assembled monolayer (SAM) was formed on the gold-coated sensor surface in order to obtain a reusable sensing surface. The low detection limit for the optimized assay, calculated as the concentration that produces a 10% decrease in the blank signal, is 20 ng/L. A complete assay cycle, including regeneration, is accomplished in 25 min. Additionally, a study of the matrix effects of different types of wastewater was performed. All measurements were carried out with the SPR sensor system (β-SPR) commercialised by the company Sensia, S.L. (Spain). The small size and low response time of the β-SPR platform would allow it to be used in real contaminated locations. The immunosensor was evaluated and validated by measuring the atrazine content of 26 natural samples collected from Ebro River. Solid-phase extraction followed by gas chromatography coupled to mass spectrometric detection (SPE–GC–MS) was used to validate the new immunoassay.     

Determination of major and trace elements in human scalp hair by pressurized-liquid extraction with acetic acid and inductively coupled plasma–optical-emission spectrometry

An analytical method has been developed for determination of major (Ca, K, Mg, and Na) and trace elements (As, Cd, Co, Li, Ni, and Sr) in human scalp hair. The proposed method includes a novel, simple, rapid, highly efficient, and automated metal-leaching procedure, by pressurized-liquid extraction (PLE), combined with a rapid simultaneous detection system—inductively coupled plasma–optical-emission spectrometry (ICP–OES). PLE is one of the most promising recently introduced sample-preparation techniques, with the advantages of reducing solvent consumption and enabling automated sample handling. The operating conditions for PLE, including concentration of the extraction solvent, extraction temperature, static time, number of extraction steps, pressure, mean particle size, diatomaceous earth (DE) mass/sample mass ratio, and flush volume were studied using an experimental design (Plackett–Burman design, PBD). The optimum conditions were use of 0.75 mol L⁻¹ acetic acid as extracting solution and powdered hair samples thoroughly mixed with DE, as a dispersing agent, at a DE mass/sample mass ratio of 4. Extraction was performed at room temperature and an extraction pressure of 140 atm for 5 min in one extraction step. The flush volume was fixed at 60%. The PLE-assisted multi-element leaching proposed is complete after 7 min (5 min static time plus 1 min purge time plus 1 min end relief time). Under the optimised conditions the figures of merit, for example limits of detection and quantification, repeatability of the over-all procedure, and accuracy, were evaluated. Analysis of GBW-07601 (human hair) certified reference material revealed accuracy was good for the target elements. The optimised method was finally applied to several human scalp-hair samples.     

Cyanides and isocyanides of first-row transition metals: molecular structure, bonding, and isomerization barriers

Cyanides and isocyanides of first-row transition metal M(CN) (M=Sc-Zn) are investigated with quantum chemistry techniques, providing predictions for their molecular properties. A careful analysis of the competition between cyanide and isocyanide isomers along the transition series has been carried out. In agreement with the experimental observations, late transition metals (Co-Zn) clearly prefer a cyanide arrangement. On the other hand, early transition metals (Sc-Fe), with the only exception of the Cr(CN) system, favor the isocyanide isomer. The theoretical calculations predict the following unknown isocyanides, ScNC(3Delta), TiNC(4Phi), VNC(5Delta), and MnNC(7Sigma+), and agree with the experimental observation of FeNC(6Delta) and the CrCN(6Sigma+) cyanide. First-row transition metal cyanides and isocyanides are predicted to have relatively large dissociation energies with values within the range 80-101 kcal mol(-1), except Zn(CN), which has a dissociation energy around 50-55 kcal mol(-1), and low isomerization barriers. A detailed analysis of the bonding has been carried out employing the topological analysis of the charge density and an energy decomposition analysis. The role of the covalent and electrostatic contributions to the metal-ligand bonding, as well as the importance of pi bonding, are discussed.     

Direct organocatalytic synthesis of enantiopure succinimides from beta-lactam aldehydes through ring expansion promoted by azolium salt precatalysts

A single-step catalytic ring expansion approach from 4-oxoazetidine-2-carbaldehydes to enantiopure succinimides has been achieved by the use of a base (DBU) and a thiazolium salt precatalyst.     

Electrocatalytic and magnetic properties of ultrathin nanostructured iron-melanin films on Au(111)

We have prepared ultrathin, nanostructured melanin films on Au(111) by means of electrochemical self-assembly. These films were characterized by using Auger electron spectroscopy, X-ray absorption near-edge structure spectroscopy, scanning tunneling microscopy, magnetic force microscopy, and electrochemical techniques. Two types of nanostructures are present in the film: melanin nanoparticles and Fe(3)O(4) nanoparticles. The melanin nanoparticles contain Fe bonded to oxygen-containing phenolic groups in an octahedral configuration similar to that found in Fe(2)O(3). The inorganic-organic composite exhibits magnetic properties and catalyzes the electroreduction of hydrogen peroxide in alkaline and neutral electrolyte solutions. The electrocatalytic activity depends on the Fe-bound melanin and appears to be similar to that found for Fe-porphyrins.