An experimental study of airfoil instability tonal noise with trailing edge serrations

This paper presents an experimental study of the effect of trailing edge serrations on airfoil instability noise. Detailed aeroacoustic measurements are presented of the noise radiated by an NACA-0012 airfoil with trailing edge serrations in a low to moderate speed flow under acoustical free field conditions. The existence of a separated boundary layer near the trailing edge of the airfoil at an angle of attack of 4.2 degree has been experimentally identified by a surface mounted hot-film arrays technique. Hot-wire results have shown that the saw-tooth surface can trigger a bypass transition and prevent the boundary layer from becoming separated. Without the separated boundary layer to act as an amplifier for the incoming Tollmien–Schlichting waves, the intensity and spectral characteristic of the radiated tonal noise can be affected depending upon the serration geometry. Particle Imaging Velocimetry (PIV) measurements of the airfoil wakes for a straight and serrated trailing edge are also reported in this paper. These measurements show that localized normal-component velocity fluctuations that are present in a small region of the wake from the laminar airfoil become weakened once serrations are introduced. Owing to the above unique characteristics of the serrated trailing edges, we are able to further investigate the mechanisms of airfoil instability tonal noise with special emphasis on the assessment of the wake and non-wake based aeroacoustic feedback models. It has been shown that the instability tonal noise generated at an angle of attack below approximately one degree could involve several complex mechanisms. On the other hand, the non-wake based aeroacoustic feedback mechanism alone is sufficient to predict all discrete tone frequencies accurately when the airfoil is at a moderate angle of attack.     

Accelerated formation of the boron–oxygen complex in p‐type Czochralski silicon

This Letter reports on the acceleration of the rate of formation of the boron–oxygen defect in p‐type Czochralski silicon with illumination intensities in excess of 2.1 × 10¹⁷ photons/cm²/s. It is observed that increased light intensities greatly enhance the rate of defect formation, without increasing the saturation concentration of the defect. These results suggest a dependence of the defect formation rate upon the total majority carrier concentration. Finally, a method using temperatures up to 475 K and an illumination intensity of 1.68 × 10¹⁹ photons/cm²/s is shown to result in near‐complete defect formation within seconds. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Chemistry of chloroethylenes on Cu(100): bonding and reactions

The bonding and reactions of chloroethylenes (vinyl chloride, trans- and cis-dichloroethylene, trichloroethylene) on a Cu(100) surface have been investigated by temperature-programmed desorption and reaction, near-edge X-ray absorption fine structure (NEXAFS) studies and measurements of changes of the surface work function. The monolayer molecules adsorb molecularly intact at 95 K via π coordination. The molecules orient with their molecular planes parallel to the surface with little increase (<0.02 Å) in the C---C bond distance compared with the gas phase values. The degree of thermal dissociation increases with the extent of halogenation, and no chlorine is present in the hydrocarbon reaction products liberated from the surface. Both cis- and trans-1.2-chloroethylene produce acetylene and a small amount of benzene, while dissociation of trichloroethylene generates acetylene and deposits a carbon residue on the surface. Vinyl chloride desorbs from Cu(100) without reaction.     

Quantitative measurements of Ge surface segregation during SiGe alloy growth

Ge segregation during the growth of Si_{1 − x}Ge_x alloys (x = 5, 10, 20, and 40%) was studied using X-ray photoelectron spectroscopy. The alloys were grown in thicknesses up to 20.0 nm at 500°C to measure quantitatively the amount of segregated surface Ge. The length of alloy needed to reach steady-state growth edge was found to decrease with increasing alloy concentration (4.8, 2.8, 2.4, and 2.0 nm, respectively). It was found that each alloy had a complete monolayer of Ge on the surface and an increasing amount of segregated Ge in the second layer (20, 55, 80, and 95%, respectively) during steady-state growth. An increase in the temperature of alloy growth (400–750°C) resulted in an increase in the leading edge of alloy growth but did not change the amount of segregated Ge during steady-state growth. We propose that film stress is responsible for the amount of Ge segregation.     

Mode detection in turbofan inlets from near field sensor arrays

Knowledge of the modal content of the sound field radiated from a turbofan inlet is important for source characterization and for helping to determine noise generation mechanisms in the engine. An inverse technique for determining the mode amplitudes at the duct outlet is proposed using pressure measurements made in the near field. The radiated sound pressure from a duct is modeled by directivity patterns of cut-on modes in the near field using a model based on the Kirchhoff approximation for flanged ducts with no flow. The resulting system of equations is ill posed and it is shown that the presence of modes with eigenvalues close to a cutoff frequency results in a poorly conditioned directivity matrix. An analysis of the conditioning of this directivity matrix is carried out to assess the inversion robustness and accuracy. A physical interpretation of the singular value decomposition is given and allows us to understand the issues of ill conditioning as well as the detection performance of the radiated sound field by a given sensor array.     

Trends in microdisk laser research and linear optical modelling

Research into microdisk lasers demonstrates new achievements both in the technology and in the associated physical effects and applications. Melting and rounding of the disk edge boosts the Q-factors due to improved surface smoothness. In-plane cavity shape is widely used as a design instrument. Optimal shaping of pumped area lowers the threshold power. Photonic molecules made of several microdisks as “photonic atoms” show lasing at several closely spaced frequencies. A microdisk with a single quantum dot as an active region is considered as the most promising system for realisation of a single photon emitter necessary for quantum computing. These new effects and devices can be simulated with accurate numerical techniques, developed recently for “warm-cavity” linear modelling, that are able to bring a new vision of the physics of lasing.     

Investigation of 2-D electromagnetic transients in a circular cylinder with time discontinuity in permittivity via the resolvent method

The resolvent method approach is proposed for analytically solving the time domain Volterra integral equation (TDVIE) which describes the electromagnetic fields in 2-D cylindrical structures with time changes in the permittivity. It is shown that the approach allows investigation of the electromagnetic field transformation due to an abrupt time change in dielectric permittivity inside a circular cylinder as well as the construction of the Green’s function for an initial-boundary value problem. Key mechanisms of electromagnetic field transformation are investigated and a qualitative distinction of the processes is shown that depends on an initial field configuration.     

Comparison of rigid and flexible simple point charge water models at supercritical conditions

This study investigates the differences between the predictions of various properties of rigid and flexible simple point charge water models at supercritical conditions. Molecular dynamics simulations were conducted for supercritical water in a temperature range of 773–1073 K and densities in the range 115–659 kg/m³. We present thermodynamic data, pair correlation functions, self-diffusivity, power spectra, dielectric constants, and variaous measures of hydrogen bonding at different state conditions. The flexible water model performs better in predicting the pressures along the supercritical isotherms simulated. Agreement between experimental and calculated dielectric constants is superior for the flexible water model, particularly at high densities. The flexible model exhibits a greater degree of hydrogen bonding and more persistent hydrogen bonds than does the rigid model. The structural features of supercritical water at high densities are identical for the two water models. At low densities, however, the flexible potential exhibits pair correlation functions with enhanced peaks. Inclusion of flexibility in the potential model does not result in a significant shift in the position of the rotational/librational peak in the power spectrum. The self-diffusivities obtained from the simulations are within the accuracy of the experimental values for both the rigid and flexible models. On balance the inclusion of flexibility improves agreement with the properties of real supercritical water while incurring little or no additional computational burden. © 1996 by John Wiley & Sons, Inc.