Evaluation and application of bismuth as an internal standard for the determination of lead in wines by simultaneous electrothermal atomic absorption spectrometry

A method for the direct determination of Pb in wines by simultaneous multi-element atomic absorption spectrometry (SIMAAS) using a transversely heated graphite atomizer, Zeeman-effect background corrector and internal standardization is proposed. Bismuth was used as an internal standard and Pd(NO3)2 plus Mg(NO3)2 as chemical modifier to stabilize both the analyte and the internal standard. The implementation of two pyrolysis steps avoided any build-up of carbonaceous residues on the graphite platform. All diluted samples (1 + 1 v/v) in 0.2% v/v HNO3 and reference solutions (5.0-50 microg l(-1) Pb in 0.2% v/v HNO3) were spiked with 25 microg l(-1) Bi. For a 20 microl aliquot dispensed into the graphite tube, a good correlation (r = 0.9997) was obtained between the ratio of the analyte signal to the internal standard signal and the analyte concentration of the reference solutions. The electrothermal behaviour of Pb and Bi in red, white and rosé wines were compared. In addition, absorbance variations due to changes in experimental conditions, such as atomizer temperature, integration time, injected sample volume, radiation beam intensity, graphite tube surface, dilution and sample composition, were minimized by using Bi as internal standard. Relative standard deviations of measurements based on integrated absorbance varied from 0.1 to 3.4% and from 0.5 to 7.3% (n = 12) with and without internal standard correction, respectively. Good recoveries (91-104%) for Pb spikes were obtained. The characteristic mass was 45 pg Pb and the limit of detection based on integrated absorbance was 0.9 microg l(-1) Pb. Internal standardization increased the lifetime of the tube by 25%. Direct determinations of Pb in wines with and without internal standardization approaches were in agreement at the 95% confidence level. The repeatability and the tube lifetime were improved when using Bi as internal standard. The improvement in accuracy using an internal standard was only observed when the analytical results were affected by errors.     

Highly conjugated p-quinonoid pi-extended tetrathiafulvalene derivatives: a class of highly distorted electron donors

A new class of pi-extended TTF-type electron donors (11 a-c) has been synthesized by Wittig-Horner olefination of bianthrone (9) with 1,3-dithiole phosphonate esters (10 a-c). In cyclic voltammetry experiments, donors 11 a-c reveal a single, electrochemically irreversible oxidation-yielding the corresponding dicationic products-at relatively low oxidation potentials (approximately 0.7-0.8 V). Theoretical calculations, performed at the DFT level (B3 P86/6-31 G*), predict a highly-folded C(2h) structure for 11 a. In the ground state, the molecule adopts a double saddle-like conformation to compensate the steric hindrance. The calculations suggest that the intramolecular charge transfer associated with the HOMO-->LUMO transition is responsible for an absorption band observed above 400 nm. While the radical cation 11 a*+ retains the folded C(2h) structure predicted for the neutral molecule as the most stable conformation, the dication 11 a(2+) has a fully aromatic D(2) structure, formed by an orthogonal 9,9'-bianthryl central unit to which two singly-charged dithiole rings are attached. The drastic conformational changes that compounds 11 undergo upon oxidation account for their electrochemical properties. By means of pulse radiolysis measurements, radical-induced one-electron oxidation of 11 a-c was shown to lead to the radical cation species (11 a-c*+), which were found to disproportionate with generation of the respective dication species (11 a-c(2+)) and the neutral molecules (11 a-c).     

BRCA1 mutation screening using restriction endonuclease fingerprinting-single-strand conformation polymorphism in an automated capillary electrophoresis system

Efficient mutation scanning techniques are needed for the rapid detection of novel disease-associated mutations and rare-sequence variants of putative importance. The large size of the breast cancer 1 gene (BRCA1) and the many mutations found throughout its entire coding sequence make screening for mutations in this gene particularly challenging. We have developed a method for screening exon 11 of the BRCA1 gene based on restriction enzyme digestion of fluorescence-labeled polymerase chain reaction (PCR) products followed by single-strand conformation polymorphism (SSCP) using an automated capillary electrophoresis system, denoted capillary restriction endonuclease fingerprinting (REF)-SSCP electrophoresis. Using this strategy on a control set of samples, we were able to detect 17 of 18 known sequence alterations. The method was then applied to screen 73 Norwegian females with family histories of breast and/or ovarian cancer. A total of 172 sequence alterations were detected, including substitutions, insertions, and deletions. One novel substitution of unknown function was identified. Sequencing of all samples negative in the capillary REF-SSCP system gave no additional mutations confirming the high sensitivity of the described methodology. Capillary REF-SSCP electrophoresis appeared as a technically convenient technique, requiring amplification of fewer PCR fragments than traditional SSCP. The novel strategy allows high-throughput mutation scanning without radioactive labeling and polyacrylamide gel electrophoresis (PAGE).     

S1P1-selective in vivo-active agonists from high-throughput screening: off-the-shelf chemical probes of receptor interactions, signaling, and fate

The essential role of the sphingosine 1-phosphate (S1P) receptor S1P(1) in regulating lymphocyte trafficking was demonstrated with the S1P(1)-selective nanomolar agonist, SEW2871. Despite its lack of charged headgroup, the tetraaromatic compound SEW2871 binds and activates S1P(1) through a combination of hydrophobic and ion-dipole interactions. Both S1P and SEW2871 activated ERK, Akt, and Rac signaling pathways and induced S1P(1) internalization and recycling, unlike FTY720-phosphate, which induces receptor degradation. Agonism with receptor recycling is sufficient for alteration of lymphocyte trafficking by S1P and SEW2871. S1P(1) modeling and mutagenesis studies revealed that residues binding the S1P headgroup are required for kinase activation by both S1P and SEW2871. Therefore, SEW2871 recapitulates the action of S1P in all the signaling pathways examined and overlaps in interactions with key headgroup binding receptor residues, presumably replacing salt-bridge interactions with ion-dipole interactions.     

The structure of the FeNO group in two metastable states (MS1 and MS2) of the nitroprusside anion in Na2[Fe(CN)5NO].2H2O. Infrared spectra and quantum chemistry calculations for the normal and the 15NO and N18O isotopic substituted substance

Low temperature infrared spectra of light induced metastable states MS1 and MS2 of the nitroprusside anion in Na(2)[Fe(CN)(5)NO].2H(2)O, isotopically normal and substituted with (15)NO and N(18)O, are presented and discussed. As a consequence of the relatively high population of the MS2 state achieved by further irradiation with 1064 nm light of samples previously irradiated with 488.0 nm light, new bands were seen for the first time, and others, previously reported, were confirmed. The comparison of the spectral data obtained for the FeNO moiety of the isotopically normal as well as of the (15)NO and N(18)O substituted anion with the results of quantum chemical (DFT) calculations support the assignment of the bands which appear after successive irradiations to MS1, the linear Fe(eta(1)-ON) linkage isomer, and to MS2, the side-bound Fe(eta(2)-NO) isomer.     

Thermochemistry of adducts of some bivalent transition metal bromides with 4-chloroaniline

The compounds [MBr₂(p-clan)₂] (where M is Mn(II), Fe(II), Co(II), Ni(II), Cu(II) or Zn(II); p-clan = 4-chloroaniline) were synthesized and characterized by melting points, elemental analysis, thermal analysis and electronic and IR spectroscopy. The enthalpies of solution of the adducts, metal(II) bromides and 4-chloroaniline in methanol, 1.2 M aqueous HCl or 25% (v/v) 1.2 M aqueous HCl in methanol were measures and by using thermochemical cycles, the following thermochemical parameters for the adducts have been determined: the standard enthalpies for the Lewis acid/base reactions (Δ_rH°), the standard enthalpies of formation (Δ_fH°), the standard enthalpies of decomposition (Δ_DH°), the lattice standard enthalpies (Δ_MH°) and the standard enthalpies of the Lewis acid/base reactions in the gaseous phase (Δ_rH°(g)). The mean bond dissociation enthalpies of the metal(II)-nitrogen coordinated bonds and the enthalpies of adduct formation in the gaseous phase have been estimated.     

Determination of coumarins by voltammetric techniques in micellar and emulsified media

An electroanalytical study of the oxidation processes of umbelliferone and hymecromone at a glassy carbon electrode in micellar solution and emulsified medium by different voltammetric techniques is described. The non-ionic surfactant Triton X-405 in acetate-buffered medium at pH 4.8 was found to be the most suitable. Different ranges of linearity were obtained in the micellar solutions, depending on the technique used; the limits of determination for differential pulse voltammetry (DPV) at a stationary electrode were 2.9×10^?6 mol l^?1 and 3.3×10^?6 mol l^?1 for umbelliferone and hymecromone, respectively. In the emulsified medium formed with a mixture of toluene and ethyl acetate (3:2), the oxidation processes yielded similar results. With DPV, linear calibration plots were obtained in the ranges 1.0×10^?5–9.0×10^?7 mol l^?1 umbelliferone and 1.0×10^?5–2.0×10^?6 mol l^?1 hymecromone. The media used are predominantly aqueous so that special reference electrodes and solvent purification are not needed.     

HPLC-Electrochemical detection with graphite-poly (tetrafluoroethylene) electrode Determination of the fungicides thiram and disulfiram

The suitability of composite graphite-poly(tetrafluoroethylene) (Teflon) electrodes as amperometric indicator electrodes in HPLC detection is demonstrated. The determination of the fungicides thiram and disulfiram in the presence of ziram has been chosen as an analytical problem. The optimization of working conditions, such as the choice of the organic solvent used in the mobile phase as well as its percentage, the potential applied to the composite electrode, and the time elapsed between mixing the carbamates and the injection, has been accomplished by using the wall-jet flow-cell configuration. The effect of the acetonitrile percentage used in the mobile phase on the retention of thiram, disulfiram, ziram and phenol was evaluated. Resolution up to the baseline can be achieved with 45% acetonitrile. The sensitivity of the determination of thiram and disulfiram in the presence of a constant concentration of ziram is slightly better when using a wall-jet cell; however, the background current is higher, as well as the baseline noise and the time necessary to achieve stabilization of the baseline before the injection. Lower limits of detection for both fungicides, as well as a better repeatability, were obtained when using a thin-layer flow cell configuration. As an application, the determination of thiram in spiked apple samples, at a level of 0.5 mg thiram kg(-1) apple, has been carried out with a mean recovery of 97 +/- 3% for a significance level of 0.05.     

Rh(II) catalysed intramolecular C-H insertion of diazo substrates in water: a simple and efficient approach to catalyst reuse

Water is an efficient solvent for the Rh2(OAc)4 catalysed intramolecular C-H insertion of a range of diazo substrates without competitive water insertion. Due to the high solubility and stability of the catalyst in water, the catalyst can be efficiently reused.     

Copper corrosion in buffered and non-buffered synthetic seawater: a comparative study

The electrochemical behaviour of copper in neutral buffered and non-buffered synthetic seawater and in pure chloride solutions has been studied by cyclic voltammetry, weight loss measurements, open circuit potential and scanning electron microscopy (SEM). Values of the repassivation potentials of Cu in non-buffered and buffered synthetic seawater, at 50 mV s^–1, were 0.12 and 0.46 V vs. SCE, respectively. The sharpness, heights and location of the different peaks as well as their charges were shown to be influenced by the composition of the solution, buffering conditions, deoxygenation, polarization potential and time. High chloride concentrations lead to higher oxidation charges. The anodic and the cathodic charges were shown to increase as the chloride concentration increases. The open circuit potential transients of copper in non-deoxygenated, non-buffered synthetic seawater indicate pitting from the beginning of the exposure, while in buffered solutions the pitting appeared only after a quite long exposure period, i.e. after 40 days. Corrosion rates of Cu samples after 3 months of immersion were higher in solutions of pure chloride (0.5 M) than in synthetic seawater. After six months the differences were even more noticeable. SEM images have showed a somewhat higher density of pits on copper samples immersed in the chloride solution (0.5 M), in comparison with those in synthetic seawater.