Interpretation of the polyelectrolyte and antipolyelectrolyte effects of poly(N‐vinylimidazole‐co‐sodium styrenesulfonate) hydrogels

Hydrogels of N‐vinylimidazole (VI) and sodium styrenesulfonate (SSS) were synthesized in aqueous solution by radical crosslinking copolymerization with N,N′‐methylene‐bis(acrylamide) as crosslinker. Swelling in several saline solutions was measured for hydrogel samples synthesized with different comonomer concentrations (C_T = 10, 25, or 40%) and with SSS mole fractions covering a broad range (f_SSS = 0–0.7), while the crosslinker ratio was 2 wt % in all cases. The degree of swelling in aqueous solution with a specific ionic strength (μ), plotted versus the SSS composition of the feed, shows a minimum for any set of samples synthesized with a fixed C_T. The dependence of swelling on μ shows both polyelectrolyte (f_SSS beyond the minimum) and antipolyelectrolyte behaviors (in the low f_SSS limit). It was found that the nonGaussian factor of the crosslinking density and the polymer‐solvent interaction parameter increase with f_SSS for any C_T. Moreover, in the low f_SSS limit, the osmotic swelling pressure is governed not only by the ionic contribution, but also by the polymer‐solvent mixing and, the concentration of mobile counterions inside the gel is not proportional to the net fixed charge but to the addition of cationic and anionic side groups, what discards the formation of ionic pairs. The antipolyelectrolyte effect is interpreted as due to the increasing protonation of VI as μ goes up. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1683–1693, 2007     

Differentiation of species of the Baccharis genus by HPLC and chemometric methods.

Phytochemical investigation of the aerial parts of three Baccharis species (Asteraceae family) was performed using HPLC and chemometric methods, with the objective of distinguishing between three morphologically very similar species: Baccharis genistelloides Persoon var. trimera (Less.) DC, B. milleflora (Less.) DC and B. articulata (Lam.) Persoon. With the help of Principal Component Analysis (PCA) and variance weights, it was possible to characterize the chromatographic profiles of the alcoholic extracts of the three species. Application of Soft Independent Modeling of Class Analogy (SIMCA) and K-Nearest Neighbor (KNN) methods on a training set of 74 extracts resulted in models that correctly classified all eight samples in an independent test set.     

Gas solubility of carbon dioxide in poly(lactic acid) at high pressures: Thermal treatment effect

The sorption of carbon dioxide in glassy Poly(lactic acid) (PLA) films was studied by quartz crystal microbalance (QCM) at high pressures. Two thermal treatments, melted and quenched, were performed in PLA with two different L:D contents, 80:20 and 98:2, films and compared with a third thermal protocol, annealed, and used in a previous work. The results obtained show that for pressures higher than 2 MPa, the carbon dioxide solubility is larger in PLA 80:20 than in PLA 98:2, indicating that the L:D plays a dominant role on this property. The thermal treatments only affect the gas solubility in PLA 98:2. Sorption isotherms at temperatures 303, 313, and 323 K, below the glass transition temperature of the polymer, and pressures up to 5 MPa were measured and analyzed with three different models, the dual‐mode sorption model, the Flory–Huggins equation, and a modified dual‐mode sorption model where the Henry's law term was substituted by the Flory–Huggins equation. This last model performs especially well for CO₂ in PLA 80:20, due to the convex upward curvature of the solubility isotherms for that system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 616–625, 2007     

Book reviews

Ohne Zusammenfassung

---

Book reviews

     

Pit your wits against young minds!

This column is a place for those bits of contagious mathematics that travel from person to person in the community, because they are so elegant, suprising, or appealing that one has an urge to pass them on. Contributions are most welcome.     

Multicommuted fluorometric multiparameter sensor for simultaneous determination of naproxen and salicylic acid in biological fluids.

A combined approach based on solid-phase optosensing and multicommutation principles has been applied to develop a method for the simultaneous analysis of two pharmaceuticals (naproxen and salicylic acid) in biological fluids. The multicommuted flow-through optosensor was based on direct native fluorescence measurements of both analgesics using a non-polar sorbent (C18 silica gel) as a solid sensing zone. The flow system was controlled by Java-written home-made software and designed using three-way solenoid valves for an independent automated manipulation of sample and carrier solutions. Using an optimized sampling time, the method was calibrated in the range of 1 - 25 and 5 - 200 ng mL(-1). The obtained detection limits were 0.3 and 1.3 ng mL(-1) for naproxen and salicylic acid, respectively, with RSD (%) values of better than 2% for both analytes. The proposed methodology was successfully applied to urine, serum and pharmaceutical preparations. Recovery percentages ranging from 96.1 to 104% were obtained for both analytes.     

Click chemistry in materials synthesis. III. Metal‐adhesive polymers from Cu(I)‐catalyzed azide–alkyne cycloaddition

1,2,3‐Triazole‐based polymers generated from the Cu(I)‐catalyzed cycloaddition between multivalent azides and acetylenes are effective adhesive materials for metal surfaces. The adhesive capacities of candidate mixtures of azide and alkyne components were measured by a modified peel test, using a customized adhesive tester. A particularly effective tetravalent alkyne and trivalent azide combination was identified, giving exceptional strength that matches or exceeds the best commercial formulations. The addition of Cu catalyst was found to be important for the synthesis of stronger adhesive polymers when cured at room temperature. Heating also accelerated curing rates, but the maximum adhesive strengths achieved at both room temperature and high temperature were the same, suggesting that crosslinking reaches the same advanced point in all cases. Polytriazoles also form adhesives to aluminum, but copper is bound more effectively, presumably because active Cu(I) ions may be leached from the surface to promote crosslinking and adhesion. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5182–5189, 2007