Phytohormone Supplementation Significantly Increases Growth of Chlamydomonas reinhardtii Cultivated for Biodiesel Production

Cultivation is the most expensive step in the production of biodiesel from microalgae, and substantial research has been devoted to developing more cost-effective cultivation methods. Plant hormones (phytohormones) are chemical messengers that regulate various aspects of growth and development and are typically active at very low concentrations. In this study, we investigated the effect of different phytohormones on microalgal growth and biodiesel production in Chlamydomonas reinhardtii and their potential to lower the overall cost of commercial biofuel production. The results indicated that all five of the tested phytohormones (indole-3-acetic acid, gibberellic acid, kinetin, 1-triacontanol, and abscisic acid) promoted microalgal growth. In particular, hormone treatment increased biomass production by 54 to 69 % relative to the control growth medium (Tris–acetate–phosphate, TAP). Phytohormone treatments also affected microalgal cell morphology but had no effect on the yields of fatty acid methyl esters (FAMEs) as a percent of biomass. We also tested the effect of these phytohormones on microalgal growth in nitrogen-limited media by supplementation in the early stationary phase. Maximum cell densities after addition of phytohormones were higher than in TAP medium, even when the nitrogen source was reduced to 40 % of that in TAP medium. Taken together, our results indicate that phytohormones significantly increased microalgal growth, particularly in nitrogen-limited media, and have potential for use in the development of efficient microalgal cultivation for biofuel production.     

Investigation on the stress behavior of cellulose acetate and the development of highly moisture‐resistant optical films for display devices

An optical film with high optical anisotropy was prepared by the stretching of a cellulose acetate film and the consequential orienting of a retardation‐enhancing additive. The change in retardation in response to moisture absorption was explored and it was found that the degree of the retardation variation is strongly related to the stretching temperature. Stress generated by the stretching and its relaxation was systematically investigated to elucidate the effect of stretching temperature on the irreversible change in retardation upon moisture absorption. The results show that the magnitude of releasable stress plays an important role in controlling changes in optical properties. In addition, the difference in the deformation behavior between glassy and rubbery states should be taken into account in the development of a moisture‐resistant optical film. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1470–1478     

Homogeneous liquid crystal alignment on poly(vinylidene fluoride-trifluoroethylene) films subjected to ion-beam irradiation

We demonstrate homogeneous and uniform liquid crystal (LC) alignment on poly(vinylidene fluoride-trifluoroethylene) [PVDF-TrFE] films using ion-beam (IB) irradiation and a performance improvement of twisted nematic (TN) cells using IB-irradiated PVDF-TrFE films. Spontaneous ferroelectricity of the PVDF-TrFE films was modified by IB irradiation, which affected the LC alignment properties. The variation in the pre-tilt angles of the LC molecules on the IB-irradiated PVDF films is attributed to surface reformation, including defluorination and oxidation because the pre-tilt angles of LC molecules can be controlled by adjusting the fluorine content. The results of contact angle measurements supported this phenomenon. A 58% reduction in the switching voltage was observed for TN cells, indicating that the IB-irradiated PVDF-TrFE films are a promising candidate for use as an alignment layer.     

Improved Compatibility of Styrene-Maleic Anhydride Copolymer/Polyethylene Blends Through Reactive Mixing

Abstract

To improve the compatibility of styrene-maleic anhydride copolymer/low density polyethylene (SMA/LDPE) blends, LDPE grafted with 2-hydroxyethyl methacrylate-isophorone diisocyanate (LDPE-g-HI) was prepared and blended with SMA of which anhydride was converted to carboxylic acid (SMAAc). The infrared spectra of LDPE-g-HI established the presence of isocyanate group. In the blend morphology, some adhesions between the two phases and much finer dispersions were observed in the SMAAc/LDPE-g-HI blends, indicating that chemical reactions took place during the melt blending. The lower heat capacity change at the glass transition temperature demonstrated that chemical bonds were produced in the SMAAc/LDPE-g-HI blends. From the results of the rheological test, it was found that strong positive deviation from the mixing rule occurred in viscosity for the SMAAc/LDPE-g-HI blends, concerning with good adhesion and finer dispersions. In the measurement of tensile property, the improved mechanical properties for the SMAAc/LDPE-g-HI blends were shown.     

Synthesis and characterization of novel elastomeric poly(D,L-lactide urethane) maleate composites for bone tissue engineering

Here, we report the synthesis and characterization of a novel 4-arm poly(lactic acid urethane)-maleate (4PLAUMA) elastomer and its composites with nano-hydroxyapatite (nHA) as potential weight-bearing composite. The 4PLAUMA/nHA ratios of the composites were 1:3, 2:5, 1:2 and 1:1. FTIR and NMR characterization showed urethane and maleate units integrated into the PLA matrix. Energy dispersion and Auger electron spectroscopy confirmed homogeneous distribution of nHA in the polymer matrix. Maximum moduli and strength of the composites of 4PLAUMA/nHA, respectively, are 1973.31 ± 298.53 MPa and 78.10 ± 3.82 MPa for compression, 3630.46 ± 528.32 MPa and 6.23 ± 1.44 MPa for tension, 1810.42 ± 86.10 MPa and 13.00 ± 0.72 for bending, and 282.46 ± 24.91 MPa and 5.20 ± 0.85 MPa for torsion. The maximum tensile strains of the polymer and composites are in the range of 5–93%, and their maximum torsional strains vary from 0.26 to 0.90. The composites exhibited very slow degradation rates in aqueous solution, from approximately 50% mass remaining for the pure polymer to 75% mass remaining for composites with high nHA contents, after a period of 8 weeks. Increase in ceramic content increased mechanical properties, but decreased maximum strain, degradation rate, and swelling of the composites. Human bone marrow stem cells and human endothelial cells adhered and proliferated on 4PLAUMA films and degradation products of the composites showed little-to-no toxicity. These results demonstrate that novel 4-arm poly(lactic acid urethane)-maleate (4PLAUMA) elastomer and its nHA composites may have potential applications in regenerative medicine.     

Polyvinyl alcohol-borate hydrogel containing Prussian blue for surface decontamination

A polyvinyl alcohol (PVA)-borate hydrogel-based strippable surface decontaminant containing an ammonium salt and Prussian blue (PB) was developed for the removal of ¹³⁷Cs from various surfaces. This surface decontaminant can be easily prepared by the simple mixing of commercially available materials, such as PVA, borax, NH₄Cl and PB, in water, and the decontaminant can be peeled off surfaces due to its high elastic property after surface decontamination. The hydrogel displayed an effective removal performance for Cs from painted cement, aluminum, stainless steel, and cement surfaces and a potential for reusability. Therefore, the PB/PVA-borate hydrogel has good potential as a new surface decontaminant.     

Deposition of a Continuous and Conformal Copper Seed Layer by a Large-Area Electron Cyclotron Resonance Plasma Source with Embedded Lisitano Antenna

To deposit copper seed layer on ultra large scale integration devices, a large-area (Ø 378 mm) electron cyclotron resonance plasma has been generated by using permanent magnets-embedded Lisitano antenna. The plasma source operates in the pressure range of 0.2–1.5 mTorr with microwave power range of 500–2,000 W. By using a Langmuir probe, the electron density and temperature have been measured near the DC sputter target position. Measurements indicate argon plasmas having electron densities of ~5 × 10¹⁰/cm and electron temperatures of 5 eV with 750 W microwave power at gas pressures of 0.5 mTorr. Using this plasma source and a DC sputter, we obtained excellent conformal copper seed layer with high aspect ratios of 12:1. This is in contrast with conventional methods using magnetron sputter, which has aspect ratios of 2–3:1. Also, improvements are observed in the smoothness (root mean square roughness of 1.345 nm), uniformity (2.5 % at 300 mm wafer), and sidewall symmetricity (more than 95 %) of the copper seed layer.