Corrosion products on steel 20 in aerated hydrazine solutions: Mössbauer study

Composition of corrosion layers on steel 20 in aerated solutions with hydrazine concentrations less than 11 ppm was studied at 50, 60, and 80°C in dynamic conditions by transmission Mössbauer spectroscopy and X-ray diffraction as supplementary technique. Corrosion rates were determined by gravimetric method. A comparison with corrosion in water at 80°C was made. The observed layers have not any protective character. For 0.1 m/s linear velocity, they are composed by nonstoichiometric magnetite, (Fe_3?x O₄,x=0.02–0.04) with lepidocrocite (γ-FeOOH) as secondary phase at 50°C. Haematite (α-Fe₂O₃) is observed at 60 and 80°C with a 19 nm particle size. It becomes smaller for higher velocity (0.7 m/s).     

Divinylsiloxane‐bisbenzocyclobutene‐based polymer modified with polystyrene–polybutadiene–polystyrene triblock copolymers

Divinylsiloxane‐bisbenzocyclobutene (DVS‐bisBCB) polymer has very low dielectric constant and dissipation factor, good thermal stability, and high chemical resistance. The fracture toughness of the thermoset polymer is moderate due to its high crosslink density. A thermoplastic elastomer, polystyrene–polybutadiene–polystyrene triblock copolymer, was incorporated into the matrix to enhance its toughness. The cured thermoset matrix showed different morphology when the elastomer was added to the B‐staged prepolymer or when the elastomer was B‐staged with the DVS‐bisBCB monomer. Small and uniformly distributed elastomer domains were detected by transmission electron micrographs (TEM) in the former case, but TEM did not detect a separate domain in the latter case. A high percentage of the polystyrene–polybutadiene–polystyrene triblock copolymer could be incorporated into the DVS‐bisBCB thermoset matrix by B‐staging the triblock copolymer with the BCB monomer. The elastomer increased the fracture toughness of DVS‐bisBCB polymer as indicated by enhanced elongation at break and increased K1c values obtained by the modified edge‐lift‐off test. Elastomer modified DVS‐bisBCB maintained excellent electrical properties, high T_g and good thermal stability, but showed higher coefficient of linear thermal expansion values. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1591–1599, 2006     

(1-Adamantanethio)pyridines and tetrahydropyridines from the reaction of 1-adamantanethiol with pyridine I-oxide in acetic anhydride

The reaction of pyridine 1-oxide with 1-adamantanethiol in acetic anhydride produced a mixture of 2- and 3-(1-adamantanethio)pyridines, 1-aeetyl-2-(1-adamantanethio)-3-hydroxy-4-acetoxy-1,2,3,4-telrahydropyridine and the corresponding 3-acetoxyderivative. Pure substances were separated by means of column chromatography on alumina. The tetrahydropyridines were identified by means of their proton magnetic and mass spectra. 4-(1-Adamantanethio)pyridine was synthesized from 4-chloropyridinc and 1-adamantanethiol. The three isomeric (1-adamantanethio)-pyridines were, each, cleaved by concentrated hydrochloric acid to give 1-chloroadamantane and the corresponding pyridinethiol.     

Evaluation of a complete HPLC solvent optimization system involving piece-wise quadratic modelling

Summary Interpretive methods are accepted to give the best possible results for selectivity optimization in HPLC. However the methods are very complex, and most work so far has been detailed academic studies. This paper describes an evaluation of a complete integrated system incorporating peak labelling, modelling of retention behaviour and calculation of response surfaces, with particular emphasis on the retention modelling. The peak labelling section has been discussed previously.A piece-wise quadratic function is investigated for the modelling of retention times across an isoeluotropic plane to effect selectivity optimization in HPLC. This requires 10 data-points on the isoeluotropic plane. The predicted global optimum and local optima are evaluated by comparison of calculated and experimental retention data, for a nine component sample. Seven interstitial points, distributed across the whole plane between the data-points, are similarly evaluated for a related sample. The typical error (in retention time) is less than 2%, often 1%, and the maximum error is 4.2%. At the global optimum the error was found be less than 1.3% for all 9 peaks.     

Morphology-dependent stimulated Raman scattering (MDSRS)

A novel non-linear Raman spectroscopic technique, which can be used to characterize the chemical composition of the interface region of volatile aerosol particles, is described. The technique is morphology-dependent stimulated Raman scattering (MDSRS). We discuss the phenomenology behind this new optical probe, and present experimental results which show that this technique can be used as quantitative spectroscopic tool. We outline the potential application of MDSRS to in situ gas—aerosol kinetics and dynamics studies.     

Enhancing selectivity in oxidation catalysis with sol-gel nanocomposites

Valuable organic compounds such as alpha-hydroxy acids are easily synthesised with relevant selectivity enhancement using a sol-gel hydrophobized nanostructured silica matrix doped with the organocatalyst TEMPO: A materials science based synthetic route which cannot be achieved via classical homogeneous synthesis.     

Voltamperometric determination of kinetin with a carbon paste modified electrode

The electrochemical behaviour of kinetin (6-furfurylaminopurine) on a carbon paste modified with OV-17 silicone electrode, is studied. The determination of kinetin is possible working in square wave voltammetric techniques, reaching limits of determination of 38.7 ng ml⁻¹. The proposed method was successfully applied to determine the cytokinin in extracts of apples (previously spiked with kinetin) and the obtained results were in accordance with the results obtained with HPLC-UV.