Complex morphology of melt-spun nylon-6 fibres investigated by 1H double-quantum-filtered NMR spin-diffusion experiments.

The complex morphology of high-speed melt-spun nylon-6 fibres hydrated with D2O was investigated using 1H double-quantum-filtered spin-diffusion NMR experiments. The magnetisation exchange from selected crystalline domains along the fibrils and interfibrils was simulated with the help of a three-dimensional solution of a spin-diffusion equation approximated by a product of one-dimensional analytical NMR signals, which correspond to a lamellar morphology. This allows to measure the sizes of crystalline and less-mobile amorphous domains along the fibrils, as well as the diameter of the fibrils and interfibril distances. A series of nylon-6 fibres with extreme values of winding speed and draw ratio was investigated. The changes detected in the domain size along the fibrils and interfibrils show the same trend in the data obtained from wide-angle X-ray diffraction and small-angle X-ray scattering.     

Diffusion in flows with a linearly nonuniform velocity profile

Methods of group analysis are applied to determine the Green’s function in the infinite space of the test particle diffusion equation for flows with a linearly nonuniform velocity profile. Using this function, the solutions of the Cauchy problem are obtained for certain particular initial conditions.     

Enthalpies of sorption of linear hydrocarbons (C2–C8) and chloroderivatives of methane and ethylene on the surface of hydrotalcite

Differential molar adsorption enthalpies (DMAE) were determined by gas chromatographic measurements of specific retention volume of vapors on the surface of two forms of Mg–Al hydrotalcite. A linear dependence of the DMAE on the number of the carbon atoms in hydrocarbons was observed for both form of hydrotalcite. The dependence of the differential molar adsorption enthalpies on the number of chlorine atoms in organic molecules is discussed. A linear dependence of DMAE on the molecular weight of chloroderivatives of methane and ethylene on the basic form in an order monochloromethane < dichloromethane < trichloromethane or vinylidene chloride < 1,1-dichloroethylene < trichloroethylene was found.     

Effect of nanotube functionalization on the properties of single‐walled carbon nanotube/polyurethane composites

A commercially available aliphatic thermoplastic polyurethane formulated with a methylene bis(cyclohexyl) diisocyanate hard segment and a poly(tetramethylene oxide) soft segment and chain‐extended with 1,4‐butanediol was dissolved in dimethylformamide and mixed with dispersed single‐walled carbon nanotubes. The properties of composites made with unfunctionalized nanotubes were compared with the properties of composites made with nanotubes functionalized to contain hydroxyl groups. Functionalization almost eliminated the conductivity of the tubes according to the conductivity of the composites above the percolation threshold. In most cases, functionalized and unfunctionalized tubes yielded composites with statistically identical mechanical properties. However, composites made with functionalized tubes did have a slightly higher modulus in the rubbery plateau region at higher nanotube fractions. Small‐angle X‐ray scattering patterns indicated that the dispersion reached a plateau in the unfunctionalized composites that was consistent with the plateau in the rubbery plateau region. The room‐temperature modulus and tensile strength increase was proportionally higher than almost all increases seen previously in thermoplastic polyurethanes; however, the increase was still an order of magnitude below what has been reported for the best nanotube–polymer systems. Nanotube addition increased the hard‐segment glass transition temperature slightly, whereas the soft‐segment glass transition was so diffuse that no conclusions could be drawn. Unfunctionalized tubes suppressed the crystallization of the hard segment; whereas functionalized tubes had no effect. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 490–501, 2007     

Synthesis, morphology and random laser action of ZnO nanostructures

Three-dimensional (3-D) ZnO random-wall nanostructures and one-dimensional (1-D) ZnO nanorods were prepared on silicon substrates by a simple solid-vapour phase thermal sublimation technique. Optical pumped random lasing has been observed in the ZnO random-wall arrays with a threshold intensity of 0.38 MW/cm² in the emission wavelength from 380 to 395 nm. The optical gain was attributed to the closed-loop scattering and light amplification of the ZnO random-wall. The experimental result suggests that the morphology of nanostructure is the key factor to effect random lasing.     

N. Charton,A. Feldermann,A. Theis,M. H. Stenzel,T. P. Davis,C. Barner‐Kowollik,Initiator efficiency of 2,2′‐azobis(isobutyronitrile) in bulk dodecyl acrylate free‐radical polymerizations over a wide conversion and molecular weight range (2004) 42(20) 5170–5179

The original article to which this Erratum refers was published in J Polym Sci Part A: Polym Chem (2004) 42(20) 5170–5179. No abstract.     

Growth and characterisation of Eu doped GaN thin films

We have studied the optical properties of Eu doped GaN thin films. We have grown high quality Eu doped GaN thin films by using Gas Source Molecular Beam Epitaxy (GSMBE), with 1.4% Eu concentration. The Full Width at Half Maximum (FWHM) of the X-ray diffraction in an omega scan was found to be 288 arcsecs. Low Eu concentration (0.08%) doped GaN thin films were grown, where Eu-related photoluminescence at 622 and 613 nm was detected using above band-gap excitation at 2 K. For high Eu concentration of 30% GaN:Eu crystal photoluminescence (PL) and cathodoluminescence (CL) spectra show strong and intense transitions at 622 and 664 nm, but also at 593 nm for CL spectra, with a similar transition observed from the low Eu concentration sample.     

MgO films grown on yttria-stabilized zirconia by molecular beam epitaxy

MgO films were grown on (0 0 1) yttria-stabilized zirconia (YSZ) substrates by molecular beam epitaxy (MBE). The crystalline structures of these films were investigated using X-ray diffraction and transmission electron microscopy. Growth temperature was varied from 350 to 550 °C, with crystalline quality being improved at higher temperatures. The MgO films had a domain structure: (1 1 1)[1 1 2¯]_MgO(0 0 1)[1 0 0]_YSZ with four twin variants related by a 90° in-plane rotation about the [1 1 1]_MgO axis. The observed epitaxial orientation was compared to previous reports of films grown by pulsed laser deposition and sputtering and explained as resulting in the lowest interface energy.