Evaluation of methods aimed at complete removal of template from molecularly imprinted polymers.

Polymers imprinted with clenbuterol were used to study the influence of various post-polymerization treatments [e.g., thermal annealing, microwave assisted extraction (MAE), Soxhlet extraction and supercritical fluid template desorption] on the bleeding of residual template. The aim of the study was to reduce the bleeding to levels that would allow the use of the materials as affinity phases for extraction of clenbuterol from bovine urine at concentrations below 1 ng ml-1. After treatment, the clenbuterol imprinted polymers were packed into solid-phase extraction columns and the bleeding was estimated by quantifying the amount of template released in 10 ml of methanol-acetic acid (9 + 1 v/v). This was followed by an assessment of selectivity and recovery in comparison with non-treated material. The lowest bleeding level was found after MAE using 100% trifluoroacetic acid for 3 x 20 min at 100 degrees C. The collected eluate contained in this case 3 ng ml-1 of clenbuterol. The same material was subsequently used for the extraction of clenbuterol from spiked bovine urine. The resulting selectivity and recovery were lower compared with those obtained using the untreated material. A milder but still efficient method to reduce the bleeding level was found to be MAE with formic acid. In this case a bleeding level of 14 ng ml-1 was found after only a 1 h extraction time. In a second model system, using a polymer imprinted with L-phenylalanine anilide, the bleeding was reduced to a similar level by extensive on-line washing in good swelling solvents containing acid or base additives and after thermal annealing of the polymers in the dry state.     

Development of a hybrid-fuzzy air temperature controller for a supersonic combustion test facility

 Hydrogen gas is burned in air to raise and maintain the stagnation temperature of a supersonic combustion test facility to a desired setpoint. In order to reach the desired operating conditions for stagnation temperature, there are three phases to the hydrogen control; H₂ ignition at facility start-up, H₂ ramp-up while the facility is ramped-up, and H₂ iteration to achieve the desired temperature setpoint. Each phase incorporates a different type of control. Fuzzy logic is used to design a computer based supervisory controller that recognizes the different phases of operation and chooses the appropriate control method. Received: 28 November 1999/Accepted: 2 November 2000     

Melting Point and Composition Distribution of Polyolefins by Fractionation

The fractionation technique described in this paper was used to characterize the melting-point, monomer, and blocking distributions for polymers and copolymers. It is different from the molecular-weight fractionation technique in that the fractions are obtained by using a single solvent to extract the solid polymer below its melting point at stepwise-increasing temperatures. The reproducibility of this technique is excellent, and the technique is sufficient to distinguish pellet-to-pellet variation in a commercially available polypropylene. It was used to show the influence of preparation variables on the melting-point distributions of polyethylene and polypropylene and on the monomer and blocking distribution of copolymers, and to distinguish copolymers from blends.     

Linear and nonlinear electromagnetic coupling models in vibration-based energy harvesting

This paper investigates the response of an energy harvester that uses electromagnetic induction to convert ambient vibration into electrical energy. A unique aspect of the present study is the comparison of the system's response behavior when either a linear or a physically motivated form of nonlinear coupling is applied. The motivating hypothesis for this work was that nonlinear coupling could be used to improve the performance of an energy harvester by broadening its frequency response. Combined theoretical and numerical studies investigate the harvester's response for both single and multi-frequency base excitation. Our investigations unveil regions in the parameter space where nonlinear coupling is better than linear coupling and regions where the opposite is true. The meaningful conclusion is that nonlinear coupling can sometimes be detrimental, but it can also be beneficial if properly designed into the system.     

Determination of triazine pesticides by high-performance liquid chromatography with swept-potential electrochemical detection

A swept-potential electrochemical detector, operating in the square-wave voltammetric mode, is used to detect a mixture of five triazine pesticides separated on a reverse-phase resin column. Limits of detection are below 1 ng injected. Two compounds, not completely separated by the column, are resolved on the potential axis.     

Shortness parameters for planar graphs with faces of only one type

We construct infinite sequences of non-Hamiltonian graphs and use them to show that the shortness exponent (or, in some cases, the shortness coefficient) is less than one for many classes of 3-connected planar graphs whose faces are all r-gons and whose vertices are all p-valent or q-valent, where p < q. Three of the five possible values of (r, p) are considered, namely (4.3). (3,3), and (3,4), in conjunction with most of the possible corresponding values of q.     

A novel fully implicit finite volume method applied to the lid‐driven cavity problem—Part I: High Reynolds number flow calculations

A novel implicit cell‐vertex finite volume method is described for the solution of the Navier–Stokes equations at high Reynolds numbers. The key idea is the elimination of the pressure term from the momentum equation by multiplying the momentum equation with the unit normal vector to a control volume boundary and integrating thereafter around this boundary. The resulting equations are expressed solely in terms of the velocity components. Thus any difficulties with pressure or vorticity boundary conditions are circumvented and the number of primary variables that need to be determined equals the number of space dimensions. The method is applied to both the steady and unsteady two‐dimensional lid‐driven cavity problem at Reynolds numbers up to 10000. Results are compared with those in the literature and show excellent agreement. Copyright © 2003 John Wiley & Sons, Ltd.