THE USE OF THERMOELASTICITY TO EVALUATE STRESS REDISTRIBUTION AND NOTCH SENSITIVITY IN CERAMIC MATRIX COMPOSITES

Thermoelastic stress analysis was used to document the effect of composite damage on the stress distribution in three ceramic matrix composites. Composite damage was found to significantly alter the thermoelastic response of each material, with the greatest effect noted in SiC/CAS. Thermoelastic imaging of these materials affords a more complete picture of how the various damage mechanisms affect the stress distribution. In particular, a stress concentration factor computed from thermoelastic images, serves as an indicator of stress redistribution. The stress concentration factors were computed by comparing notch root to far field temperatures, and monitored after the introduction of various amounts of damage. In each material, the stress concentration factor diminished as the damaging load approached the ultimate stress. Reduction in the stress concentration is associated with local changes in modulus, mechanistically arising from combinations of fiber, matrix and interface fracture. Stress redistribution occurs as a consequence of modulus changes, leading to lower notch sensitivity in each of the tested composites.     

Existence of black hole solutions for the Einstein-Yang/Mills equations

This paper provides a rigorous proof of the existence of an infinite number of black hole solutions to the Einstein-Yang/Mills equations with gauge groupSU(2), for any event horizon. It is also demonstrated that the ADM mass of each solutions is finite, and that the corresponding Einstein metric tends to the associated Schwarzschild metric at a rate 1/r ², asr tends to infinity.Research supported in part by the NSF, Contract No. DMS-89-05205Research supported in part by the DE, Contract No. De-FG 02-88 EF 25065     

Supersymmetry,vacuum statistics,and the fundamental theorem of algebra

I give an interpretation of the fundamental theorem of algebra based on supersymmetry and the Witten index. The argument gives a physical explanation of why a real polynomial of degreen need not haven real zeroes, while a complex polynomial of degreen must haven complex zeroes. This paper also addresses in a general and model-independent way the statistics of the perturbative ground states (the states which correspond to classical vacua) in supersymmetric theories with complex and with real superfields.     

Effect of oxygen exposure on the magnetic properties of ultrathin Co/Ge(1 1 1) films

Influences of oxygen exposure on the magnetic properties of Co/Ge(1 1 1) ultrathin films have been investigated by surface magneto-optic Kerr effect technique. As the oxygen exposure increases on Co/Ge(1 1 1) films, their magnetic properties could be modified. As an example for 15 ML Co/Ge(1 1 1) films, the coercivity increases from 730 to 920 Oe and the remanence Kerr intensity is reduced for 500 Langmuir (L) of oxygen exposure. Corresponding compositions analyzed by Auger electron spectroscopy measurement shows that the amount of oxygen on the surface layers increases with increasing the oxygen exposure time. Oxygen distributes on the topmost layers of the film. The adsorbed oxygen influences the electronic density of states of Co and results in the changes of the magnetic properties. Besides, the appearance of O/Co/Ge interface could modify the stress anisotropy, and as a result the coercivity of ultrathin Co/Ge(1 1 1) film is enhanced.     

Shape transition from InAs quantum dash to quantum dot on InP(3 1 1)A

We report on the shape transition from InAs quantum dashes to quantum dots (QDs) on lattice-matched GaInAsP on InP(3 1 1)A substrates. InAs quantum dashes develop during chemical-beam epitaxy of 3.2 monolayers InAs, which transform into round InAs QDs by introducing a growth interruption without arsenic flux after InAs deposition. The shape transition is solely attributed to surface properties, i.e., increase of the surface energy and symmetry under arsenic deficient conditions. The round QD shape is maintained during subsequent GaInAsP overgrowth because the reversed shape transition from dot to dash is kinetically hindered by the decreased ad-atom diffusion under arsenic flux.     

“Slow” active control of combustion instabilities by modification of liquid fuel spray properties

This paper describes an experimental investigation of the feasibility of using “slow” active control approaches, which “instantaneously” change liquid fuel spray properties, to suppress combustion instabilities. The objective of this control approach was to break up the feedback between the combustion process heat release and combustor pressure oscillations that drive the instability by changing the characteristics of the combustion process (e.g., the characteristic combustion time). To demonstrate the feasibility of such control, this study used a proprietary fuel injector (Nanomiser^TM), which can vary its fuel spray properties, to investigate the dependence of acoustics–combustion process coupling, i.e., the driving of combustion instabilities, upon the fuel spray properties. This study showed that by changing the spray characteristics it is possible to significantly damp combustion instabilities. Furthermore, using combustion zone chemiluminescence distributions, which were obtained by Abel’s deconvolution synchronized with measured acoustic data, it has been shown that the instabilities were mostly driven midway between the combustor centerline and wall, a short distance downstream from the flame holder, where the mean axial flow velocity is approximately zero in the vortex near the flame holder. The results of this study strongly suggest that a “slow” active control system that employs controllable fuel injectors could be effectively used to prevent the onset of detrimental combustion instabilities.     

Amorphous chalcogenide AgSbS2 films prepared by pulsed laser deposition

The pulsed laser deposition technique has been applied to prepare amorphous ternary AgSbS films. The films were prepared from AgSbS₂ bulk glass using a KrF excimer laser. The composition of prepared films according to the results of the energy dispersive X-ray analysis and the Rutherford backscattering was close to bulk one. Optical transmission and spectral dependence of the refractive index proved the good optical quality of the films. The Ar⁺ ion laser dot exposures of the films show a potential applicability of the films as a new type of optical recording material. PACS 78.66.Jg; 81.15.Fg; 81.40.Wx     

Finite element modal solutions of planar photonic crystal fibers with rectangular air-holes

Modal solutions of planar photonic crystal waveguides with rectangular air-holes are presented by using a rigorous full-vectorial finite element-based approach. The effective indices, mode field profiles, spot-sizes, power confinements, modal hybridness, beat lengths and group velocity dispersions are shown for the fundamental and higher order modes of the quasi-TE and TM polarizations.     

An improved approach for hydrogen analysis in metal samples using single laser-induced gas plasma and target plasma at helium atmospheric pressure

We report in this paper the results of an experimental study on hydrogen analysis of solid samples in high pressure helium ambient gas employing the basic scheme of laser induced breakdown spectroscopy (LIBS). It is shown that the metastable excited state of helium atom can be utilized to induce delayed excitation of the ablated hydrogen atoms, and thereby avoid the Stark broadening effect as well as overcoming the undesirable mismatch effect, which are responsible for inefficient excitation respectively. It is further demonstrated that for samples of high boiling-point materials such as zircaloy, successful hydrogen analysis can be achieved by a newly introduced double excitation technique employing single laser realized in a modified configuration of the conventional LIBS method. PACS 51-52     

High-density plasma etching of indium-zinc oxide films in Ar/Cl2 and Ar/CH4/H2 chemistries

The dry etching characteristics of transparent and conductive indium-zinc oxide (IZO) films have been investigated using an inductively coupled high-density plasma. While the Cl₂-based plasma mixture showed little enhancement over physical sputtering in a pure argon atmosphere, the CH₄/H₂/Ar chemistry produced an increase of the IZO etch rate. On the other hand, the surface morphology of IZO films after etching in Ar and Ar/Cl₂ discharges is smooth, whereas that after etching in CH₄/H₂/Ar presents particle-like features resulting from the preferential desorption of In- and O-containing products. Etching in CH₄/H₂/Ar also produces formation of a Zn-rich surface layer, whose thickness (∼40 nm) is well-above the expected range of incident ions in the material (∼1 nm). Such alteration of the IZO layer after etching in CH₄/H₂/Ar plasmas is expected to have a significant impact on the transparent electrode properties in optoelectronic device fabrication.