Expressions of dissipated powers and stored energies in poroelastic media modeled by {u,U} and {u,P} formulations

This paper is devoted to the rigorous obtention of the energy balance in porous materials. The wave propagation in the porous media is described by Biot-Allard's {u,U} and {u,P} formulations. The paper derives the expressions for stored kinetic and strain energies together with dissipated energies. It is shown that, in the case of mixed formulations, these expressions do not correspond to the real and imaginary parts of the variational formulations. A quantitative convergence analysis of finite element scheme is then undertaken with the help of these indicators. It is shown that the order of convergence of these indicators for linear finite-element is one and that they are then well fitted to check the validity of finite-element models.     

Microwave cavity perturbation technique: Part III: Applications

The resonant cavity perturbation method as described in the preceding two parts of this series is applied to study the electrodynamical properties of different materials in the microwave and millimeter wave spectral range. We briefly discuss the relevant uncertainties which are asociated with the different measurement techniques and we find that employing the amplitude technique it is possible to measure both the width and frequency to nearly the same precision. We then demonstrate the broad range of applicability of this technique by showing results obtained on several different materials, ranging from an insulator to a superconductor. The performance limitations of this technique are discussed in detail.     

Application of phased array techniques to coarse grain components inspection

Ultrasonic inspection of cast stainless steel components from primary and auxiliary cooling circuits of French Nuclear Power Plant has to face with major difficulties due to the coarse grained structure of these materials. Attenuation losses and structural noise are encountered, which limits the performances of defect detection ability, mostly in terms of degraded signal-to-noise ratio and poor sensitivity. To overcome such problems, theoretical and experimental studies have been achieved at the French Atomic Energy Commission, with support from the French Institute for Radiological Protection and Nuclear Safety. Experimental studies have been performed over stainless steel specimen of known coarse structure (equiaxial grains and/or elongated grains), containing artificial reflectors (cylindrical holes and electro-eroded surface breaking notches). Those mock-ups have been inspected using contact probes of different array designs (linear or matrix splitting), and using pulse echo or dual-element techniques. Such arrays allow to control the ultrasonic beam so as to investigate different inspection angles and focusing depths. Experiments were carried out using oblique longitudinal waves, using delay laws computed by a specific model, taking account of acoustical and geometrical properties of the probes and the inspected component. In addition, specific reconstruction techniques have been investigated to enhance the signal-to-noise ratio as well as spatial resolution. These techniques are based on beam-forming summation and multi-angle inspections. Experimental results show that such techniques allow to reduce the speckle noise and to optimise the beam resolution. Those increased performances allow to detect and to size small planar defects located at the inner wall of a thick specimen, using corner and tip diffraction echoes.     

Structure and growth kinetics of the oxidation process of Fe(001) whisker surfaces over a 10-decade pressure range

Fe(001) surfaces of whiskers of good crystalline quality were oxidized in a pressure range from 10^? 7 mbar to 1 bar at different temperatures. Epitaxial Fe₃O₄ and FeO thin films with negligible strain were grown depending on the oxidation temperatures. The kinetics of the oxide thickness growth was measured and compared with the predictions of the Fromhold–Cook theory for oxidation of metals. Some discrepancies were found and a possible explanation is presented.     

Spectrophotometric determination of noble metals with tin(II) in bromide solutions

In presence of tin(II) bromide, noble metals give coloured products which are suitable for spcctrophotometric determinations. The colours are red (platinum), yellow-orange (rhodium), yellow-brown (palladium), yellow (iridium) and violet (gold) They are extracted, except for gold, with isoamyl alcohol Platinum, rhodium and palladium can be separated from irdium, and rhodium and platinum from palladium. Rhodium and platinum can be determined simultaneously.     

Back to the future: A retrospective assessment of model‐based scenarios for the management of the shrimp fishery in French Guiana facing global change

While the number of models dedicated to predicting the consequences of alternative resource management strategies has increased, instances in which authors look back at past predictions to learn from discrepancies between these and observed developments are scarce. In the past decades, the French Guiana shrimp fishery has experienced shrimp market globalization and decreasing levels of shrimp recruitment due to environmental changes. In 2006, a bio‐economic model of this fishery was developed to simulate its possible responses to economic and environmental scenarios up to 2016. Here, we compare here these predictions to the observed trajectories. While the number of active vessels corresponds to that which was predicted, the estimated shrimp stock does not. Important driving factors had not been anticipated, including a general strike, natural disasters, and the end of the global financial crisis. These results show the importance of participative approaches involving stakeholders in the co‐construction and shared representation of scenarios. Recommendations for resource managers

• Effective fisheries resources management and a fortiori, the capacity of the fisheries to adapt to global change, requires understanding of both ecological and economics dynamics.
• The temporal trajectory of the trawling shrimp fisheries has been well monitored, and the decline of both stock and fleet is understood regarding ecological and economic changes: Changes in the environmental conditions of shrimp recruitment, and oil price increase and selling price decrease.
• However, our bio‐economic modeling work showed that, even with a good understanding of the dynamics explaining past trajectories, unpredictable events (strike, natural disasters…) have acted as other key driving factors altering the capacity of the model to represent possible futures.
• These results led us to recommend a better integration of the expertise of social and political scientists in developing models of bio‐economic systems to increase the quality of scenario predictions, and to argue for more participative approaches involving the stakeholders.

     

Sample Entropy as a Tool to Assess Lumbo-Pelvic Movements in a Clinical Test for Low-Back-Pain Patients

Low back pain (LBP) obviously reduces the quality of life but is also the world’s leading cause of years lived with disability. Alterations in motor response and changes in movement patterns are expected in LBP patients when compared to healthy people. Such changes in dynamics may be assessed by the nonlinear analysis of kinematical time series recorded from one patient’s motion. Since sample entropy (SampEn) has emerged as a relevant index measuring the complexity of a given time series, we propose the development of a clinical test based on SampEn of a time series recorded by a wearable inertial measurement unit for repeated bending and returns (b and r) of the trunk. Twenty-three healthy participants were asked to perform, in random order, 50 repetitions of this movement by touching a stool and another 50 repetitions by touching a box on the floor. The angular amplitude of the b and r movement and the sample entropy of the three components of the angular velocity and acceleration were computed. We showed that the repetitive b and r “touch the stool” test could indeed be the basis of a clinical test for the evaluation of low-back-pain patients, with an optimal duration of 70 s, acceptable in daily clinical practice.     

The adsorption of a substituted benzene,the ethynyl-trifluoro-toluene on Si(100)-2 × 1

The adsorption of 3-ethynyl-trifluoro-toluene (ETFT) on Si(100)-2 × 1 surface in ultra high vacuum is studied in the low coverage regime, through a joint experimental and theoretical approach. The STM images of both filled and empty states revealed few distinct adsorption configurations. On the basis of Density Functional Theory (DFT) calculations the STM images were simulated and three main adsorption configurations were identified, with a predominance of di-sigma bonded species that leave the benzene ring unreacted. A discussion of the reactivity of the reconstructed silicon surface towards benzene derivatives is proposed by comparing the adsorption of ETFT close related molecules, like styrene and phenylacetylene.