Mode beating in spot-size converter lasers

An anomalous modulation in the wavelength spectrum has been observed in lasers with spot-size converters. This intensity modulation is shown to be caused by beating between the fundamental lasing mode and radiation modes in the taper. This results in a periodic modulation in the net gain spectrum, which causes wavelength jumps between adjacent net gain maxima, and a drive current dependent spectral width that is expected to affect system performance. The amplitude of this spectral modulation is reduced significantly by either using an angled rear-facet which reflects the beating radiation modes away from the laser axis, or by using a nonlinear, adiabatic taper.     

Potential for micromachined actuation of ultra-wide continuously tunable optoelectronic devices

Tailored scaling represents a principle of success that, both in nature and in technology, allows the effectiveness of physical effects to be enhanced. Mutation and selection in nature are imitated in technology, e.g. by model calculation and design. Proper scaling of dimensions in natural photonic crystals and our fabricated artificial 1D photonic crystals (DBRs, distributed Bragg reflectors) enable efficient diffractive interaction in a specific spectral range. For our optical microsystems we illustrate that tailored miniaturization may also increase the mechanical stability and the effectiveness of spectral tuning by thermal and electrostatic actuation, since the relative significance of the fundamental physical forces involved considerably changes with scaling. These basic physical principles are rigorously applied in micromachined 1.55-μm vertical-resonator-based devices. We modeled, implemented and characterized 1.55-μm micromachined optical filters and vertical-cavity surface-emitting laser devices capable of wide, monotonic and kink-free tuning by a single control parameter. Tuning is achieved by mechanical actuation of one or several air-gaps that are part of the vertical resonator including two ultra-highly reflective DBR mirrors of strong refractive index contrast: (i) Δn=2.17 for InP/air-gap DBRs (3.5 periods) using GaInAs sacrificial layers and (ii) Δn=0.5 for Si₃N₄/SiO₂ DBRs (12 periods) with a polymer sacrificial layer to implement the air-cavity. In semiconductor multiple air-gap filters, a continuous tuning of >8% of the absolute wavelength is obtained. Varying the reverse voltage (U=0–5 V) between the membranes (electrostatic actuation), a tuning range of >110 nm was obtained for a large number of devices. The correlation of the wavelength and the applied voltage is accurately reproducible without any hysteresis. In two filters, tuning of 127 and 130 nm was observed for about ΔU=7 V. The extremely wide tuning range and the very small voltage required are record values to the best of our knowledge. For thermally actuated dielectric filters based on polymer sacrificial layers, Δλ/ΔU=-7 nm/V is found. Received: 10 May 2002 / Published online: 8 August 2002     

Antimagnons in ferrimagnets

Purely antiferromagnetic intrinsic oscillations of magnetic ions in a tetragonal ferrimagnet are considered. The magnetic ions occupy two double positions (forming four magnetic sublattices) so that the center of symmetry for each position is not a closed element. Not involving the total magnetization vector, the oscillations are not excited by the magnetic field; however, the oscillations can be excited by an alternating electric field or by a combination of a constant electric field and the alternating magnetic field of a certain frequency. This phenomenon is a dynamic manifestation of the magnetoelectric interaction. These oscillations, representing a new special type of spin waves (magnons), were called antimagnons. The intrinsic frequencies of antimagnons, as well as the corresponding susceptibilities, were determined. Quantitative estimates were obtained for a Mn₂Sb-based ferrimagnetic phase in both easy-axis and easy-plane orientation states.     

Synthesis of ladder-type filters based on SAW resonators

A synthesis method for ladder-type filters based on SAW resonators is described. SAW devices are designed with modified equations for coupled waves. Nomograms for choosing the geometry of the filters on ST, X-cut quartz and on 36° Y, X-cut LiTaO₃ substrates are presented. Theoretical results are compared with experimental data.     

A characterization of cardinalsκ such that 2λ = 2κ wheneverκ ≦λ < 2κ

We characterize cardinalsκ such that 2^λ = 2^κ wheneverκ ≦λ < 2^κ using ideals in small algebras of sets satisfying certain completeness and saturation conditions. Research of this author was supported by an NSF Grant.     

Influence of SiO2 in SiCp on the microstructure and impact strength of Al/SiCp composites fabricated by pressureless infiltration

The effect of SiO₂ in SiC_p and the following processing parameters on the microstructure and impact strength of Al/SiC_p composites fabricated by pressureless infiltration was investigated: Mg content in the aluminum alloy, SiC particle size, and holding time. Preforms of SiC_p in the form of rectangular bars (10 × 1 × 1 cm) were infiltrated at 1150°C in an argon→nitrogen atmosphere for 45 and 60 min by utilizing two aluminum alloys (Al-6 Mg-11 Si and Al-9 Mg-11 Si, wt.%). The results obtained show that the presence of SiO₂ in SiC affects the microstructure and impact strength of the composites significantly. When Al₄C₃ is formed, the impact strength decreases. However, a high proportion of SiC to SiO₂ limits the formation of the unwanted Al₄C₃ phase in the composites. Also, a higher content of Mg in the Al alloy lowers the residual porosity and, consequently, increases the composite strength. The impact strength grows with decrease in SiC particle size and increases considerably when the residual porosity is less than 1%. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 3, pp. 401–418, May–June, 2006.     

Plasma effects and the modulation of white light spectra in the propagation of ultrashort, high-power laser pulses in barium fluoride

We report the results of a study of white light generation in a 7.5 cm long crystal of a high band-gap material, barium fluoride, using ultrashort (<42 fs) laser pulses over a range of values of incident laser power that extend up to more than three orders of magnitude larger than the critical power for self-focusing (P_cr). We explore white light generation and the intensity and spectral distributions within filaments that are formed as a result of the interplay of self-focusing and plasma-induced defocusing. The onset of plasma effects occurs at power levels in excess of 7 GW for ultrashort pulses in BaF₂. For incident power levels that are three orders of magnitude larger than the critical power, blue-shifting of the incident laser wavelength is observed in addition to asymmetric continuum generation. The blue shift enables us to estimate the temporal variation of the electron density in the plasma that is generated within the BaF₂ crystal. PACS 52.38.Hb; 42.65.Jx; 42.65.Tg; 33.80.Wz; 52.35.Mw     

Demineralisation of a semianthracite char with molten salts/HCl: A study by X-ray diffraction

The effects of chemical heat treatments of a semianthracite char (AC) on the composition of the mineral fraction of the material are investigated. The starting char was first treated with a mixture of LiCl/KCl or LiCl/KCl/CaO at 743, 873 or 1173 K and the products obtained were then washed thoroughly with distilled water. A small fraction of these samples were treated with 10⁻³ M HCl solution. The composition changes were studied by X-ray diffraction. The predominant mineral components initially present in the starting char are quartz, mullite, muscovite and/or kaolinite and oldhamite. The treatments of AC resulted in significant changes in the mineral fraction of the material, in particular when LiCl/KCl/CaO was used. In this case, spurrite, γ-calcium orthosilicate and gehlenite were formed, which were eliminated by treatment with 10⁻³ M HCl solution.