Heat-Resistant Polymer-Grafted Carbon Black: Grafting of Poly(Organophosphazenes) onto Carbon Black Surface

Abstract

The grafting of poly(organophosphazenes) onto carbon black surface by the reaction of poly(dichlorophosphazene) (PDCP) with carbon black having sodium phenoxide groups was investigated. PDCP was prepared by the ring-opening polymerization of hexachlorocyclotriphos-phazene in solution using sulfamic acid as a catalyst. The introduction of sodium phenoxide groups onto carbon black was achieved by treatment of phenolic hydroxyl groups on the surface with sodium hydroxide in methanol. Poly(diphenoxyphosphazene) (PDPP) was successfully grafted onto carbon black by the reaction of PDCP with sodium phenoxide groups introduced onto the surface followed by the replacement of chlorine atoms in PDCP with phenoxy groups. The percentage of grafting onto carbon black increased to 206% at 30°C after 12 h. It was found that only 1.4% of sodium phenoxide groups on carbon black surface was used for the grafting of PDCP because of the blocking of the surface by grafted polymer chains. Poly(diaminophenylphosphazene) and poly-(diethoxyphosphazene) were also grafted onto carbon black surface by the treatment of PDCP-grafted carbon black with aniline and sodium ethoxide, respectively. Poly(organophosphazenes)-grafted carbon blacks produced stable colloidal dispersions in good solvents for grafted polymers. Furthermore, thermogravimetric analysis indicated that poly-(organophosphazenes)-grafted carbon blacks were stable in air about 300°C.     

Grafting of Polymers Having Pendant Peroxycarbonate Groups Onto Carbon Black and Postpolymerization of Vinyl Monomers

Abstract

Postpolymerization of vinyl monomers initiated by pendant peroxycarbonate groups of grafted polymer chains on carbon black (CB) was investigated. The grafting of polymers having pendant peroxycarbonate groups onto CB was achieved by the trapping of polymer radicals formed by the thermal decomposition of copolymers of t-butylperoxy-2-methacryloyloxyethyl-carbonate (HEPO) with vinyl monomers such as vinyl acetate (VAc), styrene (St) and methyl methacrylate (MMA). The copolymers having pendant peroxycarbonate groups were prepared by copolym-erization of HEPO with vinyl monomers using azo initiator under irradiation of UV light at room temperature. The amount of remaining pendant peroxycarbonate groups of the poly(VAc-co-HEPO)-grafted CB obtained from the reaction at 90°C was maximum and decreased above the temperature. Furthermore, the postpolymerization of vinyl monomers, such as St, MMA, and VAc was initiated in the presence of poly(VAc-co-HEPO)-grafted and poly(St-co-HEPO)-grafted CB and the corresponding polymers were postgrafted onto CB to give branched polymer-grafted CB. The percentage of poly(St)-postgrafting (proportion of post-grafted poly(St) to poly(MMA-co-HEPO)-grafted CB used) increased with increasing polymerization time, but became constant at 20% after 4 hours.     

Rational Design for Cooperative Recognition of Specific Nucleobases Using β‐Cyclodextrin‐Modified DNAs and Fluorescent Ligands on DNA and RNA Scaffolds

We propose a binary fluorimetric method for DNA and RNA analysis by the combined use of two probes rationally designed to work cooperatively. One probe is an oligonucleotide (ODN) conjugate bearing a β‐cyclodextrin (β‐CyD). The other probe is a small reporter ligand, which comprises linked molecules of a nucleobase‐specific heterocycle and an environment‐sensitive fluorophore. The heterocycle of the reporter ligand recognizes a single nucleobase displayed in a gap on the target labeled with the conjugate and, at the same time, the fluorophore moiety forms a luminous inclusion complex with nearby β‐CyD. Three reporter ligands, MNDS (naphthyridine–dansyl linked ligand), MNDB (naphthyridine–DBD), and DPDB (pyridine–DBD), were used for DNA and RNA probing with 3′‐end or 5′‐end modified β‐CyD – ODN conjugates. For the DNA target, the β‐CyD tethered to the 3′‐end of the ODN facing into the gap interacted with the fluorophore sticking out into the major groove of the gap site ( MNDS and DPDB ). Meanwhile the β‐CyD on the 5′‐end of the ODN interacted with the fluorophore in the minor groove ( MNDB and DPDB ). The results obtained by this study could be a guideline for the design of binary DNA/RNA probe systems based on controlling the proximity of functional molecules.     

Development of continuous process enabling nanofibrillation of pulp and melt compounding

Microfibrillated cellulose (MFC), a mechanically fibrillated pulp mostly consisting of nanofibrils, is a very attractive material because of its high elastic modulus and strength. Although much research has been done on composites of MFC and polypropylene (PP), it has been difficult to produce such composites at an industrial level because of the difficulties in using MFC in such composites are not only connected to the polarity (that can be improved with compatibilizers), but also with the challenge to make a homogeneous blend of the components, and also the low temperature stability of cellulose that could cause problems during processing. We developed a new processing method which enables continuous microfibrillation of pulp and its melt compounding with PP. Never-dried kraft pulp and powdered PP were used as raw materials to obtain MFC by kneading via a twin-screw extruder. Scanning electron microscopy showed nano to submicron wide fibers entangled in the powdered PP. MFC did not aggregate during the melt compounding process, during which the water content was evaporated. Maleic anhydride polypropylene (MAPP) was used as a compatibilizer to reinforce interfacial adhesion between the polar hydroxyl groups of MFC and non-polar PP. We investigated the effect of MAPP content on the mechanical properties of the composite, which were drastically improved by MAPP addition. Needle-leaf unbleached kraft pulp (NUKP)-derived MFC composites had better mechanical properties than needle-leaf bleached kraft pulp (NBKP)-derived MFC composites. Injection molded NUKP-derived MFC composites had good mechanical and thermal properties. The tensile modulus of 50 wt% MFC composite was two times, and the tensile strength 1.5 times higher than that of neat PP. The heat distortion temperature of 50 wt% MFC content composite under 1.82 MPa flexural load was increased by 53 °C, from 69 to 122 °C. This newly developed continuous process using powder resin has the potential for application at an industrial level.     

Sterically Demanding Unsymmetrical Diaryl-λ3-iodanes for Electrophilic Pentafluorophenylation and an Approach to α-Pentafluorophenyl Carbonyl Compounds with an All-Carbon Stereocenter

A sterically demanding unsymmetrical pentafluorophenyl-triisopropylphenyl-λ³-iodane was developed as an effective reagent for the electrophilic pentafluorophenylation of various β-keto esters and a β-keto amide. 17 examples of α-pentafluorophenylated 1,3-dicarbonyl compounds 3 having a quaternary carbon center are provided. The resulting compounds were nicely transformed into chiral α-pentafluorophenyl ketones with an all-carbon stereogenic center in high yields and high enantioselectivities using asymmetric organocatalysis (up to 98 % ee) or asymmetric metal catalysis (up to 82 % ee).     

Production of Alkyl Aryl Sulfides from Aromatic Disulfides and Alkyl Carboxylates via a Disilathiane–Disulfide Interchange Reaction

The results of this study show that disilathiane is an effective mediator in the synthesis of alkyl aryl sulfides with disulfides and alkyl carboxylates. Mechanistic studies suggest that disilathiane promotes cleavage of the sulfur–sulfur bond of disulfides to generate thiosilane as a key intermediate. Diselenides were also applicable to this transformation to produce the corresponding selenides.     

Transition-Metal Free Catalytic Synthesis of Trifluoromethyl Indolines by [4+1] Cycloaddition of Trifluoromethyl Benzoxazinones with Sulfur Ylides

Stereoselective catalytic synthesis of 3-trifluoromethyl indolines through the [4+1] cycloaddition of benzoxazinones and sulfur ylides in a transition-metal-free manner was developed. In the presence of a catalytic amount of sodium hydride, aza-ortho-quinone methide intermediates were formed from trifluoromethyl benzoxazinones through decarboxylation after the first nucleophilic attack of sulfur ylides, which progressed to a second nucleophilic attack of sulfur ylides, resulting in the [4+1] cycloaddition. The key for this catalytic transformation is the dual attack of sulfur ylides on substrates. This unique transition-metal-free protocol is applicable to the synthesis of non-fluorinated vinyl-, ethynyl- or methyl-substituted indolines. The synthesis of 3-trifluoromethyl indoles was also achieved described under stoichiometric conditions.     

Acyl Fluorides in Late‐Transition‐Metal Catalysis

In this Review, we summarize the current state of the art in late‐transition‐metal‐catalyzed reactions of acyl fluorides, covering both their synthesis and further transformations. In organic reactions, the relationship between stability and reactivity of the starting substrates is usually characterized by a trade‐off. Yet, acyl fluorides display a very good balance between these properties, which is mostly due to their moderate electrophilicity. Thus, acyl fluorides (RCOF) can be used as versatile building blocks in transition‐metal‐catalyzed reactions, for example, as an “RCO” source in acyl coupling reactions, as an “R” source in decarbonylative coupling reactions, and as an “F” source in fluorination reactions. Starting from the cleavage of the acyl C?F bond in acyl fluorides, various transformations are accessible, including C?C, C?H, C?B, and C?F bond‐forming reactions that are catalyzed by transition‐metal catalysts that contain the Group 9–11 metals Co, Rh, Ir, Ni, Pd, or Cu.     

Structure and properties of new olefin polymers

The relationship between molecular structures and physical properties of linear low density polyethylenes (LLDPEs) produced with single-site catalyst (SSC) was investigated. SSC polymerized LLDPE have excellent physical properties corresponding to its homogeneous molecular structure that had never been achieved by conventional Ziegler-Natta catalysts. It was found that some SSCs have the capability to produce LLDPEs with narrow molecular weight distribution but excellent melt properties. This result suggests that there exist long chain branches in these LLDPEs.