Racemization of chiral amino alcohols III: Effect of Mg or Ca addition on the activity and stability of the Co/γ-Al2O3 catalyst

The racemization of R-(-)-2-amino-1-butanol in a reaction using Co/γ-Al₂O₃ catalysts and catalysts modified by Mg or Ca was investigated in this paper. Complete racemization was achieved with a yield of over 83% at using the Mg modified Co/γ-Al₂O₃ catalyst under optimized reaction conditions of 170°C and 2.5 MPa of H₂. The catalysts were thoroughly characterized by XRD, XPS, TPR, SEM and TEM. The addition of Mg and Ca may be advantageous for dispersing and stabilizing the active species of the Co/γ-Al₂O₃ catalyst, protecting from sintering, significantly improving its catalytic activity and stability.     

CuAl2O4 powder synthesis by sol-gel method and its photodegradation property under visible light irradiation

Nanocrystalline spinel CuAl₂O₄ powders were prepared by sol-gel method from nitrate Cu(NO₃)₂·3H₂O, Al(NO₃)₃·9H₂O and complex C₆H₈O₇·H₂O. Sintering was carried out at 400, 500, 600, 700, 800°C respectively for 2 h in air. The XRD patterns started to appear CuAl₂O₄ peaks after sintering of 500°C and consist of only CuAl₂O₄ peaks as spinel crystal after sintering of 700°C. The powders were analyzed by TEM and UV-vis diffuse reflectance spectrum to be round, about 10–30 nm in size and Eg=1.77 eV. Photodegradation property of nanocrystalline CuAl₂O₄ powders was investigated by using methyl orange as model pollutant and mercury lamp (λ>400 nm) as energy source. The results indicated that CuAl₂O₄ powders sintered at 700°C had the excellent visible photocatalytic property. Under the irradiation of visible light, methyl orange could be degraded 97% in 120 min.     

A multiple coupling approach to produce high-performance SERS substrates

In this work, large area gold-nanoparticle-cluster pillar array with a gold mirror as high-performance SERS substrate was facilely fabricated by combined use of nanosphere lithography and self-assembly approach.     

Improvement of an automatic HPLC system for nitropolycyclic aromatic hydrocarbons: removal of an interfering peak and increase in the number of analytes.

An automatic HPLC system for analyzing nitropolycyclic aromatic hydrocarbons (NPAHs, nitroarenes) in airborne particulates was previously described (Anal. Chim. Acta, 2001, 445, 20). Some problems with this system were that it generated a peak originating from an ascorbic acid solution that elutes at a retention time close to that of 1,6-dinitropyrene (DNP), and that it was able to analyze only 1,3-, 1,6-, 1,8-DNPs and 1-nitropyrene (I-NP). Here, we describe an improved system that effectively removes the interfering peak by introducing an ODS column just after the pump for the ascorbic acid solution, and which is capable of analyzing several additional compounds (2-, 4-NPs, 2-nitrofluorene. 6-nitrochrysene, 7-nitrobenz[a]anthracene, 3-nitroperylene and 6-nitrobenzo[a]pyrene etc.). The improved sensitivities were achieved by concentrating the compounds in a benzene-ethanol extract from airborne particulates, by increasing the loading time of the sample solution from 20 to 38 min, and by increasing the flow rate of an ascorbic acid solution from 1.3 to 1.8 mL/min.     

Anodic behavior of nickel-based alloys in the electrolytic production of NF3

The Ni-based alloys, such as Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si, prepared by hot isostatic pressing (HIP) at 1000 °C under 2 × 10⁸ Pa for 2 h were employed as the anodes for electrolytic production of NF₃. The current efficiencies for NF₃ formation were 42-38, 52-40, 52-47, 63-62, 50 and 41% for Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloys, respectively. The current efficiencies only on Ni-Cu alloys with Cu concentrations lower than 10 mol% were almost the same as those on Ni sheet and HIPed Ni anodes, whereas those on the other alloys used in this study were smaller compared with those on both Ni anodes. On the other hand, the current losses caused by anodic dissolution of Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloy electrodes were 7.95-4.42, 6.40-7.02, 5.60-6.30, 3.34-6.33, 5.10 and 0.18%, respectively. The anode consumptions of Ni-5 mol% Cu and Ni-5 mol% Si alloys were almost the same or smaller compared with those of Ni sheet and HIPed Ni electrodes, though those of other alloys used were large compared with those of both Ni anodes. Consequently, addition of Cu to the nickel matrix is available for a cheaper cost of anode with keeping a same current efficiency as that on the Ni anode and addition of Si to the nickel matrix is effective for decreasing anode consumption largely. A Ni sheet electrode containing a trace of impurities, such as Co, Mn, Ag and Al, is also favorable as the anode for electrolytic production of NF₃.     

DNA电化学生物传感器测定水中痕量铅

采用物理涂附法将单链DNA固定到金表面得到ssDNA/Au修饰电极。研究表明,该电极在pH 5,0.2 mol/L NaAc-HAc缓冲底液中,可用于测定水中痕量Pb2 。Pb2 以Pb-DNA络合物的形式吸附在电极上,以示差脉冲伏安法测定Pb2 ,在0.15 V(vsSCE)处有灵敏的氧化峰,其峰电流与Pb2 浓度在5.0×10-8~1.0×10-6mol/L范围内呈良好的线性关系,此法的检测限为2.0×10-8mol/L,该修饰电极的稳定性和抗干扰性都较好。用该电极对饮用水中的Pb进行检测,得到了满意的结果。     

The outer valance orbital electron densities of cyclopentane by binary (e,2e) spectroscopy

The binding energy spectra and electron distributions in momentum space of the valence orbitals of cyclopentane (C(5)H(10)) are studied by Electron Momentum Spectroscopy (EMS) in a noncoplanar symmetric geometry. The impact energy was 1200 eV plus binding energy and energy resolution of the EMS spectrometer was 1.2 eV. The experimental momentum profiles of the outer valence orbitals are compared with the theoretical momentum distributions calculated using Hartree-Fock and density functional theory (DFT) methods. The shapes of the experimental momentum distributions are generally quite well described by both the Hartree-Fock and DFT calculations when the large and diffuse basis sets are used.     

A New Activation Method for Electroless Metal Plating：Palladium Laden via Bonding with Self—Assembly Monolayers

A new activation method has been developed for electroless copper plating on silicon wafer based on palladium chemisorption on SAMs of APTS without SnCl2 sensitization and roughening condition.A closely packed electroless copper film with strong adhesion is successfully formed by AFM observation.XPS study indicates that palladium chemisorption occurred via palladium chloride bonding to the pendant amino group of the SAMs.     

Colloidal adhesion of phospholipid vesicles: high-resolution reflection interference contrast microscopy and theory

High-resolution reflection interference contrast microscopy (HR-RICM) was developed for probing the deformation and adhesion of phospholipid vesicles induced by colloidal forces on solid surfaces. The new technique raised the upper limit of the measured membrane–substrate separation from 1 to 4.5 μm and improved the spatial resolution of the heterogeneous contact zones. It was applied to elucidate the effects of wall thickness, pH and osmotic stress on the non-specific adhesion of giant unilamellar vesicles (ULV) and multilamellar vesicles (MLV) on fused silica substrates. By simultaneous cross-polarization light microscopy and HR-RICM measurements, it was observed that ULV with the wall thickness of a single bilayer would be significantly deformed in its equilibrium state on the substrate as the dimension of its adhesive–cohesive zone was 29% higher than the theoretical value of a rigid sphere with the same diameter. Besides, electrostatic interaction was shown as a significant driving force for vesicle adhesions since the reduction in pH significantly increased the degree of deformation of adhering ULV and heterogeneity of the adhesion discs. The degree of MLV deformation on the solid surfaces was significantly less than that of ULV. When the wall thickness of vesicle increased, the dimension of contact zone was reduced dramatically due to the increase of membrane bending modulus. Most important, the adhesion strength of colloidal adhesion approached that of specific adhesion. Finally, the increase of osmotic stress led to the collapse of adhering vesicles on the non-deformable substrate and raised the area of adhesive contact zone. To interpret these results better, the equilibrium deformation of adhering vesicle was modeled as a truncated sphere and the adhesion energy was calculated with a new theory.     

能动抛光磨盘的变形实验研究

 能动抛光磨盘实时产生不同的表面变形，在对大口径非球面光学元件进行精磨和抛光时实现与工件表面良好的大尺寸吻合，可以消除传统光学加工采用小尺寸磨头时带来的高频残余误差并提高加工效率。以加工直径1.3m左右，F/2的抛物面光学元件为例，对能动磨盘在不同离轴度时能够产生的变形进行了计算和实验。结果表明，能动磨盘能够以较高精度产生旋转对称或非对称的抛物面形状。对能动磨盘产生变形后的残余误差进行了分析。