Influence of the pore size of reversed phase materials on peptide purification processes

The influence of the pore size of a chromatographic reversed phase material on the adsorption equilibria and diffusion of two industrially relevant peptides (i.e. a small synthetic peptide and insulin) has been studied using seven different reversed phase HPLC materials having pore sizes ranging from 90 Å to 300 Å. The stationary phase pore size distribution was obtained by inverse size exclusion measurement (iSEC). The effect of the pore size on the mass transfer properties of the materials was evaluated from Van Deemter experiments. It has been shown that the lumped mass transfer coefficient increases linearly with the average pore size. The Henry coefficient and the impurity selectivity were determined in diluted conditions. The saturation capacity of the main peptides was determined in overloaded conditions using the inverse method (i.e. peak fitting). It was shown that the adsorption equilibria of the peptides on the seven materials is well described by a surface-specific adsorption isotherm. Based on this a lumped kinetic model has been developed to model the elution profile of the two peptides in overloaded conditions and to simulate the purification of the peptide from its crude mixture. It has been found that the separation of insulin from its main impurity (i.e. desamido-insulin) was not affected by the pore size. On the other hand, in the case of the synthetic peptide, it was found that the adsorption of the most significant impurity decreases with the pore size. This decrease is probably due to an increase in silanol activity with decreasing pore size.     

Thermochemistry of La0.7Sr0.3Mn1−xFexO3 solid solutions (0<x<1)

The structure, the energetics and the internal redox reactions of La_0.7Sr_0.3Fe_xMn_1−xO₃ have been studied in the complete solid solution range 0.0<x<1.0. High temperature oxide melt drop solution calorimetry was performed to determine the enthalpies of formation from binary oxides and the enthalpy of mixing. There is a noticeable change in the energetics of the solid solution near x=0.7, which is due to the growing concentration of Fe⁴⁺ at higher Fe/(Fe+Mn) ratio. The balance between different valences of the transition metals, Mn and Fe, is the main factor in determining the energetics of the La_0.70Sr_0.30Fe_xMn_1−xO₃ solid solution.     

Identifying the Geometric Site Dependence of Spinel Oxides for the Electrooxidation of 5-Hydroxymethylfurfural

Co-based spinel oxides, which are of mixing valences with the presence of both Co²⁺ and Co³⁺ at different atom locations, are considered as promising catalysts for the electrochemical oxidation of 5-hydroxymethylfurfural (HMF). Identifying the role of each atom site in the electroxidation of HMF is critical to design the advanced electrocatalysts. In this work, we found that Co²⁺_Td in Co₃O₄ is capable of chemical adsorption for acidic organic molecules, and Co³⁺_Oh play a decisive role in HMF oxidation. Thereafter, the Cu²⁺ was introduced in spinel oxides to enhance the exposure degree of Co³⁺ and to boost acidic adsorption and thus to enhance the electrocatalytic activity for HMF electrooxidation significantly.     

Fluorescent sensing platform for low-cost detection of Cu2+ by coumarin derivative: DFT calculation and practical application in herbal and black tea samples

A fluorogenic probe based on a coumarin-derivative for Cu²⁺ sensing in CH₃CN/H₂O media (v/v, 95/5, 5.0 μM) was developed and applied in real samples. 3-(4-chlorophenyl)-6,7-dihydroxy-coumarin (MCPC) probe was obtained by synthetic methodologies and identified by spectral techniques. The probe MCPC showed remarkable changes with a “turn-off” fluorogenic sensing approach for the monitoring of Cu²⁺ at 456 nm under an excitation wavelength of 366 nm. The response time of the probe MCPC was founded as only 1 min. The detection limit of the probe MCPC was recorded to be 1.47 nM. The binding constant and possible stoichiometric ratio (1:1) values were determined by Benesi-Hildebrand and Job’s plot systems, respectively. The mechanism of the probe MCPC with Cu²⁺ was further confirmed by ESI-MS and FT-IR analyses, as well as supported by theoretical calculations. Furthermore, the probe MCPC was successfully employed for the practical applications to sense Cu²⁺ in different herbal and black tea samples. The proposed sensing method was also verified by ICP-OES method.     

Minor amounts of glycerol improve the properties of polyisobutylene‐based polyurethane and its nanocomposites

The synthesis of primary hydroxyl‐telechelic polyisobutylene, HOCH₂‐PIB‐CH₂OH, often yields product the number average terminal functionality ( $f_{n,{\mathrm{CH}}_2\mathrm{OH}}$) of which is less than theoretical 2.0, typically $f_{n,{\mathrm{CH}}_2\mathrm{OH}}$ = 1.75–1.95. Polyurethane (PU) prepared with such low‐cost imperfect PIB‐diols, unsurprisingly, exhibit poor overall properties. Herein we report that mechanical, rheological, and thermal properties of polyisobutylene‐based polyurethane (PIB‐PU) and PIB‐PU reinforced with organically modified montmorillonite (OmMMT) prepared with PIB‐diol of $f_{n,{\mathrm{CH}}_2\mathrm{OH}}$ = 1.85 are significantly enhanced by glycerol. Specifically, we document that calculated minor amounts of glycerol substantially improves tensile strength, ultimate elongation, elastic modulus, toughness, rubbery plateau, flow temperature, creep, permanent set, rate of recovery after loading, and thermal properties of PIB‐PU and OmMMT‐reinforced PIB‐PU prepared with PIB‐diol of $f_{n,{\mathrm{CH}}_2\mathrm{OH}}$ = 1.85. The observations are summarized and discussed in terms of chemistry, micromorphology, and viscoelasticity. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 929–935     

Development of reactive methacrylates based on glycidyl methacrylate

Six methacrylate monomers have been synthesized for use as reactive diluents in dental composites and evaluated to investigate the relationship between molecular structure and monomer reactivity. Four were synthesized by reactions of glycidyl methacrylate (GMA) with various acids, 2‐(2‐methoxyethoxy)acetic acid ( 1 ), 2‐(2‐(2‐methoxyethoxy)ethoxy)acetic acid ( 2 ), cyanoacetic acid ( 3 ), and benzoic acid ( 4 ); others were synthesized by reactions of GMA with diethyl hydrogen phosphate ( 5 ) or methanol ( 6 ). Monomers 1 and 2 are novel, 3 seems to be novel, 4 and 6 were synthesized via a novel method, and the synthesis of 5 was described in the literature. The monomers showed high crosslinking tendencies during thermal bulk polymerizations. The photo‐, homo‐, and copolymerization behavior of the monomers with 2,2‐bis[4‐(2‐hydroxy‐3‐methacryloyloxy)phenyl]propane (Bis‐GMA) were investigated. The maximum rate of polymerizations of monomers 2 – 6 was found to be greater than triethyleneglycol dimethacrylate, Bis‐GMA, 2‐hydroxyethyl methacrylate, and glycerol dimethacrylate. For the more reactive monomers ( 2 , 3 , and 4 ), the oxygen sensitivity of polymerization was found to be low due to a hydrogen abstraction/chain transfer reaction. The computationally calculated dipole moment and lowest unoccupied molecular orbital energies indicated that there seems to be a correlation between these quantities and reactivity for ester linked monomers ( 1 – 5 ), which was also supported by ¹³C NMR data. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3787–3796, 2010     

Computational study of alkyllithium/pyridine derivative systems as initiators for the living anionic polymerization of methyl methacrylates

The reactivity of n‐butyllithium (n‐BuLi) toward pyridine derivatives (pyridine, pyridazine, pyrimidine, and 1,3,5‐triazine) was subjected to a computational study to determine the most suitable n‐BuLi/heterocyclic ring system as an initiator for the anionic polymerization of methyl methacrylate (MMA). These systems were suggested to prevent side reactions occurring through n‐BuLi attack on the carbonyl carbon of MMA by sterically blocking the initiator. The initiation reaction was modeled with the B3LYP methodology 6‐31+G*. Activation barriers were used to analyze the reactivity of each n‐BuLi/heterocyclic ring system. Computational results showed that n‐BuLi/triazine had a significantly lower activation barrier. Therefore, n‐BuLi/triazine was the suggested initiator system for the anionic polymerization of poly(methyl methacrylate). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 455–467, 2005     

Why do some Fischer indolizations fail?

The mechanisms of the Fischer indole synthesis and competing cleavage pathways were explored with SCS-MP2/6-31G(d) and aqueous solvation calculations. Electron-donating substituents divert the reaction pathway to heterolytic N-N bond cleavage and preclude the acid-promoted [3,3]-sigmatropic rearrangement.