Microstructural properties of sintered Al–Cu–Mg–Sn alloys

A non-commercial Al4Cu0.5Mg alloy has been used for investigating the effects of the elemental Sn additions. Uniaxial die compaction response of the alloys in terms of green density was examined, and the results showed that Sn addition has no effect when compacting conducted under high pressures. In total, 93–95% green density was achieved with an applied pressure of 400 MPa. Thermal events occurring during the sintering of the emerging alloys were studied by using differential scanning calorimetry (DSC). First thermal event on the DSC analysis of the Al4Cu0.5Mg1Sn alloy is the melting of elemental Sn, whereas for Al4Cu0.5Mg alloy, it is the formation of Al–Mg liquid nearly at 450 °C. Also it is clearly seen on the DSC analysis that Sn addition led to an increase in the formation enthalpy of Al–Mg liquid phase. High Sn content and high sintering temperature (620 °C), therefore high liquid-phase content, caused decrease on the mechanical properties due to thick intergranular phases and grain coarsening. Highest transverse rupture strength and hardness values were obtained from Al4Cu0.5Mg0.1Sn alloy sintered at 600 °C and measured as 390 MPa and 73 HB, respectively.     

The construction of a DC high voltage precision divider

A precise DC high-voltage divider was designed and constructed for use as a standard. The ratio of the divider for precise measurement must be known accurately independent of voltage and time. The changes in total resistance of a divider with voltage and time should be considered before design and construction. The divider consists of 100 wire-wound resistors with a total resistance of about 100 MΩ as the high-voltage arm and one wire-wound resistor with resistance of 100 kΩ as the low-voltage arm. The high voltage and ground electrodes were designed to prevent electric field concentration and corona formation at high voltages. A current measuring instrument with 6.5 digit resolution was developed to allow comparison of entering and existing currents for detection of current leakage. Considering the sources of error, a relative uncertainty of 66 ppm (parts per million) was obtained with coverage factor k = 2 for the constructed DC high-voltage divider.     

2-pyrrolidone - capped Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocrystals

Water-soluble Mn₃O₄ nanocrystals have been prepared through thermal decomposition in a high temperature boiling solvent, 2-pyrrolidone. The final product was characterized with XRD, SEM, TEM, FTIR and Zeta Potential measurements. Average crystallite size was calculated as ∼15 nm using XRD peak broadening. TEM analysis revealed spherical nanoparticles with an average diameter of 14±0.4 nm. FTIR analysis indicated that 2-pyrrolidone coordinates with the Mn₃O₄ nanocrystals only via O from the carbonyl group, thus confining their growth and protecting their surfaces from interaction with neighboring particles.      

Filter-radiometer-based realization of candela and establishment of photometric scale at UME

The luminous intensity unit of candela was realized based on filter-radiometer, which is traceable to detector-based primary standard electrical substitution cryogenic radiometer (ESCR). In that realization the traditional Osram Wi41/G-type incandescent lamp and filter-radiometer consisting of an aperture, a V(λ) filter and a silicon photodiode based trap detector were used as light source and detection element, respectively. Measurement techniques of effective aperture area, spectral transmittance of V(λ) filter and absolute responsivity of trap detector are also presented.     

Energy elastic effects and the concept of temperature in flowing polymeric liquids

The incorporation of energy elastic effects in the modeling of flowing polymeric liquids is discussed. Since conformational energetic effects are determined by structural features much smaller than the end-to-end vector of the polymer chains, commonly employed single conformation tensor models are insufficient to describe energy elastic effects. The need for a local structural variable is substantiated by studying a microscopic toy model with energetic effects in the setting of a generalized canonical ensemble. In order to examine the dynamics of flowing polymeric liquids with energy elastic effects, a thermodynamically admissible set of evolution equations is presented that accounts for the evolution of the microstructure in terms of a slow tensor, as well as a fast, local scalar variable. It is demonstrated that the temperature used in the definition of the heat flux is directly related to the Lagrange multiplier of the microscopic energy in the generalized canonical partition function. The temperature equation is discussed with respect to, first, the dependence of the heat capacity on the polymer conformation and, second, the possibility to measure experimentally the effects of the conformational energy.

Split‐type octonion matrix

The split and hyperbolic (countercomplex) octonions are eight‐dimensional nonassociative algebras over the real numbers, which are in the form , where e_m's have different properties for them. The main purpose of this paper is to define the split‐type octonion and its matrix whose inputs are split‐type octonions and give some properties for them by using the real quaternions, split, and hyperbolic (countercomplex) octonions. On the other hand, to make some definitions, we present some operations on the split‐type octonions. Also, we show that every split‐type octonions can be represented by 2 × 2 real quaternion matrix and 4 × 4 complex number matrix. The information about the determinants of these matrix representations is also given. Besides, the main features of split‐type octonion matrix concept are given by using properties of  real quaternion matrices. Then, 8n × 8nreal matrix representations of split‐type octonion matrices are shown, and some algebraic structures are examined. Additionally, we introduce real quaternion adjoint matrices of split‐type octonion matrices. Moreover, necessary and sufficient conditions and definitions are given for split‐type octonion matrices to be special split‐type octonion matrices. We describe some special split‐type octonion matrices. Finally, oct‐determinant of split‐type octonion matrices is defined. Definitive and understandable examples of all definitions, theorems, and conclusions were given for a better understanding of all these concepts.     

Synthesis and investigation of antibacterial activities and carbonic anhydrase and acetyl cholinesterase inhibition profiles of novel 4,5-dihydropyrazol and pyrazolyl-thiazole derivatives containing methanoisoindol-1,3-dion unit

Novel 4,5-dihydropyrazole derivatives (3a–i), 3-(4-((3aR,4S,7R,7aS)-1,3-dioxo-3a,4,7,7a-tetrahydro-1H-4,7-methanoisoindol-2(3H)-yl)phenyl)-5-phenyl-4,5-dihydro-1H-pyrazole-1-carbothio amide, were obtained by the addition of thiosemicarbazide (2) to the chalcones (1a–i). The addition–cyclization of 2,4′-dibromoacetophenone (4) to pyrazole derivatives (3a–i) gave the new pyrazolyl-thiazole derivatives (5a–i), (3aR,4S,7R,7aS)-2-(4-(1-(4-(4-bromophenyl)thiazol-2-yl)-5-phenyl-4,5-dihydro-1H-pyrazol-3-yl)phenyl)-3a,4,7,7a-tetrahydro-1H-4,7-methanoisoindole-1,3(2H)-dione. Antibacterial and acetylcholinesterase (AChE) enzyme and human carbonic anhydrase (hCA) I, and II isoform inhibitory activities of the compounds 3a–i and 5a–i were investigated. Some of the compounds showed promising antibacterial activity. In addition, the hCA II and I were effectively inhibited by the lately synthesized derivatives, with K_i values in the range of 18.90?±?2.37 ?58.25?±?13.62?nM for hCA II and 5.72?±?0.98 ?37.67?±?5.54?nM for hCA I. Also, the K_i parameters of these compounds for AChE were obtained in the range of 25.47?±?11.11???255.74?±?82.20?nM. Also, acetazolamide, clinical molecule, was used as a CA standard inhibitor that showed K_i value of 70.55?±?12.30?nM against hCA II, and 67.17?±?9.1?nM against hCA I, and tacrine inhibited AChE showed K_i value of 263.67?±?91.95.     

Oxalic acid removal from wastewater using multi-walled carbon nanotubes: Kinetic and equilibrium analysis

Oxalic acid adsorption from aqueous solution is studied in this work. Multi-walled carbon nanotubes (MWCNT) were used as an adsorbent. The investigated adsorption variables are equilibrium time, initial acid concentration, and temperature. The experimental results were presented using equilibrium isotherm and kinetic models. The used equilibrium models are Langmuir, Freundlich, and Temkin adsorption isotherms. And the kinetic models are Elovich, Lagergren pseudo-first-order and pseudo-second-order kinetic models. The thermodynamics studies were carried out at three different temperatures: 278, 298, and 318 K. Langmuir isotherm was the best fitted equilibrium model for the experimental data. The all applied kinetic models fitted the data suitably.     

Determination of Folic Acid by CE in Various Cultivated Variety of Lentils

A simple extraction and determination method for folic acid (FA) in lentil samples was developed employing capillary electrophoresis. The analysis was performed in a 75 μm ID fused silica capillary using a running buffer of 10 mM sodium borate (10%, v/v, methanol, pH 9) at +18 kV and a detection wavelength at 200 nm. Methylparaben was used as the internal standard. FA signal response was linear in the range between 1.2 × 10^?5 and 4.8 × 10^?5 M. Limit of detection (inter-day) was determined at 6.12 × 10^?7 M (3.3 σs^?1). The amount of FA found in green, red and mignon lentils was found to range between 0.408 and 0.742 mg g^?1.