Progress in Optical Waveguiding Thin Films

Overview of recent activities in the development of active and passive thin film waveguides, waveguide lasers and laser-deposited waveguiding films is given. Published results and parameters are summarized. The focus is on films fabricated by laser deposition.     

TiO2 thick films supported on reticulated macroporous Al2O3 foams and their photoactivity in phenol mineralization

TiO₂ thick films deposited on macroporous reticulated Al₂O₃ foams with pore size of 10 ppi and 15 ppi were prepared using dip coating from slurries of Aeroxide^® P25 nanopowder and precipitated titania. All prepared films have sufficiently good adhesion to the surface of the substrate also in case of strongly cracked films. No measurable release of deposited TiO₂ after repeated photocatalytic cycles was observed. The photocatalytic activity was characterized as the rate of mineralization of aqueous phenol solution under irradiation of UVA light by TOC technique. The best activity was obtained with Aeroxide^® P25 coated Al₂O₃ foam with the pore size of 10 ppi, annealed at 600 °C. The optimal annealing temperature for preparation of films from precipitated titania could be determined at 700 °C. Films prepared by sol-gel deposition technique were considerably thinner compared to coatings made of suspensions and their photocatalytic activity was significantly smaller.     

Diamond/graphite content and biocompatibility of DLC films fabricated by PLD

Biocompatibility and physicochemical properties of diamond-like carbon (DLC) thin layers prepared by pulsed laser deposition method were studied. The films of high and low diamond/graphite content were prepared by changing the laser energy density on the graphite target from 4 to 11 J cm⁻². The bonds and surface properties as roughness, atomic force microscopy topology, contact angle parameters, and zeta potential were measured. The cell adhesion/proliferation on DLC layers was tested using normal human fibroblasts and keratinocytes.     

Formation of copper islands on a native SiO2 surface at elevated temperatures

A combination of in situ X-ray photoelectron spectroscopy analysis and ex situ scanning electron- and atomic force microscopy has been used to study the formation of copper islands upon Cu deposition at elevated temperatures as a basis for the guided growth of copper islands. Two different temperature regions have been found: (I) up to 250 °C only close packed islands are formed due to low diffusion length of copper atoms on the surface. The SiO₂ film acts as a barrier protecting the silicon substrate from diffusion of Cu atoms from oxide surface. (II) The deposition at temperatures above 300 °C leads to the formation of separate islands which are (primarily at higher temperatures) crystalline. At these temperatures, copper atoms diffuse through the SiO₂ layer. However, they are not entirely dissolved in the bulk but a fraction of them forms a Cu rich layer in the vicinity of SiO₂/Si interface. The high copper concentration in this layer lowers the concentration gradient between the surface and the substrate and, consequently, inhibits the diffusion of Cu atoms into the substrate. Hence, the Cu islands remain on the surface even at temperatures as high as 450 °C.     

Impact of silica environment on hyperfine interactions in 𝜖-Fe2O3 nanoparticles

Magnetic nanoparticles have found broad applications in medicine, especially for cell targeting and transport, and as contrast agents in MRI. Our samples of ??-Fe₂O₃ nanoparticles were prepared by annealing in silica matrix, which was leached off and the bare particles were then coated with amorphous silica layers of various thicknesses. The distribution of particle sizes was determined from the TEM pictures giving the average size ～20 nm and the thickness of silica coating ～5; 8; 12; 19 nm. The particles were further characterized by the XRPD and DC magnetic measurements. The nanoparticles consisted mainly of ??-Fe₂O₃ with admixtures of ～1 % of the α phase and less than 1 % of the γ phase. The hysteresis loops displayed coercivities of ～2 T at room temperature. The parameters of hyperfine interactions were derived from transmission Mössbauer spectra. Observed differences of hyperfine fields for nanoparticles in the matrix and the bare ones are ascribed to strains produced during cooling of the composite. This interpretation is supported by slight changes of their lattice parameters and increase of the elementary cell volume deduced from XRD. The temperature dependence of the magnetization indicated a two-step magnetic transition of the ??-Fe₂O₃ nanoparticles spread between ～85 K and ～150 K, which is slightly modified by remanent tensile stresses in the case of nanoparticles in the matrix. The subsequent coating of the bare particles by silica produced no further change in hyperfine parameters, which indicates that this procedure does not modify magnetic properties of nanoparticles.     

Thin SiC<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> layers prepared by hybrid laser–magnetron deposition

Thin SiC _x films were fabricated by hybrid laser–magnetron deposition system. KrF excimer laser was used for deposition of carbon and magnetron at the same time for sputtering of Si species. Films were fabricated in argon/hydrogen ambient with and without additional RF discharge. The substrate temperature was changed up to 700°C. Films topology, crystallinity, composition, chemical bonds and optical emission spectra were studied. Films were smooth and amorphous. Films of thickness 400–1000 nm were fabricated. Adhesion moved from 8 to 14 N, depending on deposition conditions.     

Surface State‐Induced Anomalous Negative Thermal Quenching of Multiferroic BiFeO3 Nanowires

Wide‐bandgap semiconductor nanowires with surface defect emission centers have the potential to be used as sensitive thermometers and optical probes. Here, we show that the green luminescence of multiferroic BiFeO₃ (BFO) nanowires shows an anomalous negative thermal quenching (NTQ) with increasing temperatures. The release of trapped carriers from localized surface defect states is suggested as the possible mechanism for the increased green luminescence which was experimentally observed at elevated temperatures. A reasonable interpretation of the photoluminescence (PL) processes in BFO nanowires is achieved, and the activation energies of the PL quenching and thermal hopping are deduced. Negative thermal quenching of BFO nanowires provides a new strategy for optical thermometry at higher temperatures.     

Synthesis and electrorheology of rod-like titanium oxide particles prepared via microwave-assisted molten-salt method

The rod-like titanium dioxide (TiO₂) particles were synthesized by a simple and rapid microwave-assisted molten-salt method. The X-ray diffraction analysis revealed the phase composition transformation from the anatase phase of original TiO₂ nanomaterial to the rutile phase of high crystallinity. Scanning electron microscopy proved the conversion of originally globular particles of original anatase TiO₂ sized from 200 to 500 nm into rods with a length of 5–10 μm and a diameter between 0.5 and 2 μm. The electrorheological (ER) measurements performed under steady-state flow as a function of the applied electric field strength and particle concentration showed that suspended rutile rod-like TiO₂ particle-based fluid exhibits much higher ER activity than that of original anatase TiO₂ material powder. These observations were clearly demonstrated by viewing their dielectric spectra analyses.     

Electrochemistry of Cobalta Bis(dicarbollide) Ions Substituted at Carbon Atoms with Hydrophilic Alkylhydroxy and Carboxy Groups

In this study we explore the effect on the electrochemical signals in aqueous buffers of the presence of hydrophilic alkylhydroxy and carboxy groups on the carbon atoms of cobalta bis(dicarbollide) ions. The oxygen-containing exo-skeletal substituents of cobalta bis(dicarbollide) ions belong to the perspective building blocks that are considered for bioconjugation. Carbon substitution provides wider versatility and applicability in terms of the flexibility of possible chemical pathways. However, until recently, the electrochemistry of compounds substituted only on boron atoms could be studied, due to the unavailability of carbon-substituted congeners. In the present study, electrochemistry in aqueous phosphate buffers is considered along with the dependence of electrochemical response on pH and concentration. The compounds used show electrochemical signals around −1.3 and +1.1 V of similar or slightly higher intensities than in the parent cobalta bis(dicarbollide) ion. The signals at positive electrochemical potential correspond to irreversible oxidation of the boron cage (the C2B9 building block) and at negative potential correspond to the reversible redox process of (CoIII/CoII) at the central atom. Although the first signal is typically sharp and its potential can be altered by a number of substituents, the second signal is complex and is composed of three overlapping peaks. This signal shows sigmoidal character at higher concentrations and may be used as a diagnostic tool for aggregation in solution. Surprisingly enough, the observed effects of the site of substitution (boron or carbon) and between individual groups on the electrochemical response were insignificant. Therefore, the substitutions would preserve promising properties of the parent cage for redox labelling, but would not allow for the further tuning of signal position in the electrochemical window.