Air-Segmented Continuous-Flow Analysis for Molybdenum in Various Geochemical Samples

 An air-segmented continuous-flow method has been developed for the determination of molybdenum at ultra trace levels using the catalytic effect of molybdate during the oxidation of L-ascorbic acid by hydrogen peroxide. Incorporation of an on-line ion exchange column improved the tolerance limit for various ions. The detection limits with and without the column were 64 pmol L⁻¹ and 17 pmol L⁻¹, and the reproducibilities at 10 nmol L⁻¹ were 2.1% and 0.2%, respectively. The proposed method was applied to the determination of molybdenum in seawater and lake water as well as in rock and sediment samples. This method has the highest sensitivity among the available literature to our knowledge, and is also convenient for routine analysis of molybdenum in various natural samples. Author for correspondence. E-mail: masahito.sugiyama@ sojin0206.mbox.media.kyoto-u.ac.jp Received October 23, 2002; accepted January 28, 2003 Published online May 19, 2003     

Anodic behavior of nickel-based alloys in the electrolytic production of NF3

The Ni-based alloys, such as Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si, prepared by hot isostatic pressing (HIP) at 1000 °C under 2 × 10⁸ Pa for 2 h were employed as the anodes for electrolytic production of NF₃. The current efficiencies for NF₃ formation were 42-38, 52-40, 52-47, 63-62, 50 and 41% for Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloys, respectively. The current efficiencies only on Ni-Cu alloys with Cu concentrations lower than 10 mol% were almost the same as those on Ni sheet and HIPed Ni anodes, whereas those on the other alloys used in this study were smaller compared with those on both Ni anodes. On the other hand, the current losses caused by anodic dissolution of Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloy electrodes were 7.95-4.42, 6.40-7.02, 5.60-6.30, 3.34-6.33, 5.10 and 0.18%, respectively. The anode consumptions of Ni-5 mol% Cu and Ni-5 mol% Si alloys were almost the same or smaller compared with those of Ni sheet and HIPed Ni electrodes, though those of other alloys used were large compared with those of both Ni anodes. Consequently, addition of Cu to the nickel matrix is available for a cheaper cost of anode with keeping a same current efficiency as that on the Ni anode and addition of Si to the nickel matrix is effective for decreasing anode consumption largely. A Ni sheet electrode containing a trace of impurities, such as Co, Mn, Ag and Al, is also favorable as the anode for electrolytic production of NF₃.     

Freezing of Lennard-Jones fluid in cylindrical nanopores under tensile conditions

We have shown the Lennard-Jones (LJ) phase diagram for a slit-shaped nanopore by molecular simulations and thermodynamically predicted the results with no adjustable parameter. With this success, LJ phase diagrams are predictable. In this study, the freezing of an LJ CH₄ capillary condensate under a tensile condition in a nonstructural carbon nanopore with a cylindrical geometry was examined using molecular dynamics (MD) simulation. We employ a unit cell in contact with a bulk vapor phase, which is useful for the determination of the bulk vapor pressure in equilibrium with the molecules in a pore. The MD simulation results show liquid-solid (amorphous) phase transitions with a variation in the bulk vapor pressure. The frozen particles are arranged in concentric circular regions along the wall similar to those reported by Maddox and Gubbins. The freezing points are determined from the variations in density, enthalpy, arrangement, and structural functions. The obtained liquid-solid coexistence points are found to exhibit a significant dependence of the freezing point on the equilibrium bulk vapor pressure, forming an extraordinarily skewed curve on the p-T diagram, in contrast to the bulk phase coexistence that is represented by an almost vertical line. The origin of the significant dependence is considered to be the Laplace effect on the capillary condensate similar to the case with a slit-shaped pore. A simple model, which the authors earlier presented for slit-shaped nanopores, successfully predicted the p-T relation of the freezing point for cylindrical nanopores as well.     

Stereoselective allyl amine synthesis through enantioselective addition of diethylzinc and [1,3]-chirality transfer: synthesis of lentiginosine and polyoxamic acid derivative

A new synthetic method for the preparation of allyl amines has been developed. The key steps of this method are enantioselective addition of diethylzinc and [1,3]-chirality transfer through the [3.3] sigmatropic rearrangement of allyl cyanates. Stereocontrolled syntheses of lentiginosine (1) and polyoxamic acid derivative 2 from a common intermediate 7 derived from D-tartaric acid (8), have been accomplished.     

Vinyl Polymerization. 274. Polymerization of Acrylonitrile Initiated by the System Tetramethyl Tetrazene and Co(II) Chloride

Abstract

The binary system of tetramethyl tetrazene (TMT) and Co(II) chloride was used as initiator of acrylonitrile (AN) in dimethylformamide. The initial rate of polymerization (Rp) was found to be expressed by Rp = k[TMT]^0.62[Co(II) chloride]^0.57 [AN]^2.00

The polymerization was confirmed to proceed via a radical mechanism. The over-all activation energy for the polymerization was estimated as 15.1 kcal/mole. On the basis of these results and the product analysis of the reaction between the catalyst components in the absence of monomer, the initiation mechanism of the polymerization is discussed.     

Polymerization of Acrylonitrile Initiated by the System Tetramethyl-2-tetrazene and p-Toluenesulfonic Acid

The polymerization of acrylonitrile (AN) initiated by tetramethyl-2-tetrazene (TMT) and p-toluenesulfonic acid (TSA) in dimethylformamide (DMF) was studied. The polymerization was confirmed to proceed through a radical mechanism. The initial rate of polymerization R was expressed by the equation: R_p = k[TMT]^0.6 [TSA]^0.46 [AN]^1.35. The overall activation energy for the polymerization was estimated as 20.7 kcal/mole. In the absence of monomer, the reaction of TMT with TSA was also studied kinetically by measuring the evolution of nitrogen. From these results and ESR measurement of the TMT/TSA system, a possible initiation mechanism is proposed.     

Asymmetric Induction Copolymerization of Optically Active N-(1-Menthyl Carboxylatomethyl) Citraconimide with Methyl Methacrylate

Copolymerization of an optically active N-(1-menthyl carboxylatomethyl)citraconimide (MCMCI) was carried out with methyl methacrylate (MMA) with azobisisobutyronitrile as the initiator in benzene at 50°C. All the copolymers obtained were optically active. After the removal of the optically active menthyl group, the hydrolyzed poly(MCMCI-co-MMA)'s still showed optical activity. The asymmetric induction to the copolymer main chain and the mechanism are discussed based on the measurements of optical rotatory dispersion and circular dichroism of the original and hydrolyzed copolymers.     

Vinyl Polymerization. 439. Vinyl Polymerization Initiated by Poly(Ethylene Glycol] Diglycolic Acid or its Sodium Salt

Abstract

The polymerization of some kinds of vinyl monomer was found to occur in aqueous solutions of poly(ethylene glycol) diglycolic acid (PEG Acid) or sodium poly(ethylene glycol) diglycolate (PEG Acid Na) through radical mechanisms without any further initiator, as a so-called “uncatalyzed polymerization.” Although the initiating radical species for PEG Acid was determined to be the same as that for PEG Acid Na by means of the spin-trapping technique, the initiating ability of PEG Acid was higher than that of PEG Acid Na. These results are assumed to be attributable to the difference in the initiation mechanisms of the two systems and in the incorporating abilities of monomer into the hydrophobic areas formed by PEG Acid and PEG Acid Na.