物理实验课程考核、评估体系初探

对物理实验课程考核、评估方法进行了探讨，提出了物理实验课程考核、评估体系及实施细则．重点介绍了体系中的核心部分——正规的物理实验课程考试．     

Homoclinic and Periodic Orbits Arising Near the Heteroclinic Cycle Connecting Saddle-focus and Saddle Under Reversible Condition

In this paper, we study the dynamical behavior for a 4-dimensional reversible system near its heteroclinic loop connecting a saddle-focus and a saddle. The existence of infinitely many reversible 1-homoclinic orbits to the saddle and 2-homoclinic orbits to the saddle-focus is shown. And it is also proved that, corresponding to each 1-homoclinic （resp. 2-homoclinic） orbit F, there is a spiral segment such that the associated orbits starting from the segment are all reversible 1-periodic （resp. 2-periodic） and accumulate onto F. Moreover, each 2-homoclinic orbit may be also accumulated by a sequence of reversible 4-homoclinic orbits.     

西咪替丁的应用进展

综述了近年来国内外报道的H2受体抗拮剂－西咪替丁应用于除治疗消化性溃疡以外的其他疾病的进展情况，以其为临床用药提供参考。     

约束装箱问题的混合遗传算法求解

本将最佳适应法和遗传算法相结合，提出了一种新的启发式混合遗传算法对具有时间约束的装箱问题进行求解，给出了具体的算法步骤，试算结果表明基于启发式算法的混合遗传算法适合于求解各种约束条件下的大规模装箱问题。     

多项式理想准素分解的算法

讨论了多项式理想准素分解的算法,对于理想坐标变换中关键的“一般位置”的计算,给出了一个确定算法,并建立了特别规范Groebner基的概念,利用这一概念及文中提供的相应算法,可以方便地计算理想的维数,进而使用降维的方法来得到高维理想的准素分解。     

Melt rheology of polylactide/montmorillonite nanocomposites

In this article, the linear and nonlinear shear rheological behaviors of polylactide (PLA)/clay (organophilic‐montmorillonite) nanocomposites (PLACNs) were investigated by an Advanced Rheology Expanded System rheometer. The nanocomposites were prepared by master batch method using a twin‐screw extruder with poly(ε‐caprolactone) (PCL) as a compatibilizer. The presence of org‐MMT leads to obvious pseudo‐solid‐like behaviors of nanocomposite melts. The behaviors caused by the formation of a “percolating network” derived from the reciprocity among the strong related sheet particles. Therefore, the storage moduli, loss moduli, and dynamic viscosities of PLACNs show a monotonic increase with MMT content. Nonterminal behaviors exists in PLACNs nanocomposites. Besides the PLACNs melts show a greater shear thinning tendency than pure PLA melt because of the preferential orientation of the MMT layers. Therefore, PLACNs have higher moduli but better processibility compared with pure PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3189–3196, 2007     

Preparation,thermal properties,and flame retardance of epoxy–silica hybrid resins

A novel epoxy system was developed through the in situ curing of bisphenol A type epoxy and 4,4′‐diaminodiphenylmethane with the sol–gel reaction of a phosphorus‐containing trimethoxysilane (DOPO–GPTMS), which was prepared from the reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) with 3‐glycidoxypropyltrimethoxysilane (GPTMS). The preparation of DOPO–GPTMS was confirmed with Fourier transform infrared, ¹H and ³¹P NMR, and elemental analysis. The resulting organic–inorganic hybrid epoxy resins exhibited a high glass‐transition temperature (167 °C), good thermal stability over 320 °C, and a high limited oxygen index of 28.5. The synergism of phosphorus and silicon on flame retardance was observed. Moreover, the kinetics of the thermal oxidative degradation of the hybrid epoxy resins were studied. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2354–2367, 2003     

有机化合物电子光谱中的助色基及其作用机理探讨(Ⅰ)

本文就电子光谱中助色基的作用进行了讨论 ,认为不能一概地认为助色基能使与之相连的生色基最大吸收波长统统发生红移 ,而应具体问题具体分析 :对于n→π 来说 ,一方面助色基的p轨道和生色基的最低π 反键空轨道相互作用 ,使π 反键轨道能量上升 ,另一方面助色基的p轨道和生色基的n轨道正交 ,n轨道能量基本保持不变 ,因此n→π 跃迁能增加 ,吸收波长发生蓝移。对于π→π 跃迁来说 ,助色基的p轨道和生色基的最高π成键轨道相互作用生成的新的最高π成键轨道 ,能量虽然有所升高 ,但升高的程度与π 反键轨道升高的程度相比 ,在一些化合物中π轨道升高程度较大 ,因而π→π 跃迁能减小 ,吸收波长发生红移 ;在另一些化合物中π轨道升高程度较小 ,因而π→π 跃迁能增加 ,吸收波长发生蓝移。     

A retractable structure based on Bricard linkages and rotating rings of tetrahedra

Retractable structures which alter their geometries according to practical requirements are widely used in roof structures of stadiums for their versatility. A retractable structure based on threefold-symmetric Bricard linkages and rotating rings of tetrahedra is proposed and developed in this paper. By replacing each link of a threefold-symmetric Bricard linkage with a tetrahedron, a retractable structure is obtained which can repeatedly open and close by rotating the tetrahedra. The geometric relationship between the retractable structure and the threefold-symmetric Bricard linkage is derived and ranges of main geometric parameters are determined to ensure a continuous and smooth movement in the deployment of the structure. Then the relative displacement of the support and the open rate of the structure, two main parameters concerned in practical applications, are investigated. Preferred ranges of main geometric parameters are proposed and a physical model is manufactured to verify them. A discussion on some possible improvements and modifications of the structure is also presented.