Effect of structural variation within cationic azo-surfactant upon photoresponsive function in aqueous solution

The cationic azo-surfactants possessing different spacers and tail alkyl chain lengths have been synthesized by azocoupling ofp-alkylaniline orop-ethoxyaniline with phenol, followed by alkylation and quaternalization with dibromoalkane and trimethylamine, respectively. These surfactants showed a good solubility in water. A reversibletrans-cis isomerization of the azosurfactants by photoirradiation was assessed by UV-Vis absorption spectra. Due to a difference in HLB between thetrans- andcis-surfactants, the observed critical micelle concentration (CMC) values and the electric conductivity of the surfactant solution at above the CMC were significantly affected by the photoinducedtrans-cis isomerization. The azo-surfactants bearing moderate alkyl chain lengths such as surfactants 6 (R₂=C₂H₄, R₃=C₄H₉) and 9 (R₂=C₄H₈, R₃=C₂H₅) were found to be effective to achieve large CMC changes (3.6 mmol/L for 6 and 5.9 mmol/L for 9) by UV-light irradiation. The replacement of the tail chain species also affected the photoresponsive function. The surfactant 12, possessingp-ethoxy group as the tail chain, was found to form a stable micelle aggregation as compared with the structurally related surfactant 10 having ethyl unit as its tail group, but it exhibited a large CMC change (5.3 mmol/L) by UV-light irradiation.     

High-quality hydroxyapatite coating on biocompatible materials by laser-assisted laser ablation method

A new method for high-quality hydroxyapatite (HAp) coating is developed, the laser-assisted laser ablation method. In this method, two lasers are used. One is used for ablation of a HAp target. The other, the assist laser, is used to irradiate a Ti substrate surface. The effects of the assist laser irradiation are to anneal the HAp coating and to improve its adhesive strength to the Ti substrate. The quality of the HAp coating depends on the delay time of the assist-laser irradiation. HAp coatings obtained at a delay time of 10 microseconds or more are more amorphous. It was confirmed that the amorphous part of a coating dissolves in simulated body fluid, while the crystalline part does not. The value of the Ca/P ratio in a coating obtained at a delay time of a few microseconds is close to the stoichiometric value. PACS 81.16.Mk     

Basic study of the gelation of dimethacrylate‐type crosslinking agents

An investigation was made of the gelation of dimethacrylate‐type crosslinking agents in view of an application for separation media. The study mainly centered on a crosslinking agent, glycerol dimethacrylate (GDMA), which is relatively hydrophilic because of a hydroxyl group in the middle of its structure. The gelation of GDMA was compared with that of other hydrophobic crosslinking agents such as ethylene glycol dimethacrylate and 1,6‐hexanediol dimethacrylate. The diluents used in the study were toluene, toluene with methanol, and cyclohexanol. The gelation was observed in real time with a charge coupled device camera and dynamic light scattering (DLS). Also, the separated dry gels were extensively characterized with scanning electron microscopy, BET (N₂ absorption and desorption isotherm), and Fourier transform infrared. DLS analysis showed a stronger molecular interaction of GDMA gelation in toluene, whereas this interaction was much weaker in an alcoholic solvent such as toluene with methanol or cyclohexanol. This indicated that GDMA gelation might proceed through hydrogen bonding as well as a crosslinking reaction of vinyl groups. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 949–958, 2006     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Preparation and properties of isobutylene–isoprene rubber–clay nanocomposites

Isobutylene isoprene rubber (IIR)‐clay nanocomposites have been prepared successfully by melt intercalation with maleic anhydride‐grafted IIR (Ma‐g‐IIR) and organophilic clay. In IIR‐clay nanocomposites, the silicate layers of the clay were exfoliated and dispersed into the monolayer. The nanocomposites exhibited greater gas barrier properties compared with those of Ma‐g‐IIR. When 15 phr clay was added, gas barrier properties were 2.5 times greater than those of Ma‐g‐IIR. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1182–1188, 2006     

Thermal properties and fracture toughness of a liquid‐crystalline epoxy resin cured with an aromatic diamine crosslinker having a mesogenic group

A mesogenic‐type curing agent was synthesized to introduce a mesogenic group not only into epoxy resin backbones but also into the crosslink units. In the mesogenic curing agent system, the domain size became larger, and the network arrangement in each domain existed to a greater extent than that in a system cured with the ordinary diamine curing system according to the evidence from polarized optical micrographs and polarized Fourier transform infrared mapping measurements. Moreover, the fracture toughness of the system was considerably improved. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2486–2494, 2006     

Investigation of the drying conditions for amidosulfuric acid.

The drying conditions for primary standards of volumetric analysis have a significant effect on the titration results due to changes in the purity, stability and homogeneity. Amidosulfuric acid, a strong acid used as a reference material for volumetric analysis in Japan, was dried in a vacuum desiccator or heated at different temperatures, and then measured by Karl-Fischer titration, thermogravimetry/mass spectroscopy (TG-MS), ion chromatography and coulometric titration. The optimum drying conditions were at 50 degrees C for 24 h with crushing.