Q-switched and mode-locked diode-pumped Nd:YAG laser with an LT-GaAs

Simultaneous Q-switching and mode-locking (QML) is accomplished in a diode-pumped Nd:YAG laser using low-temperature GaAs (LT-GaAs) as the saturable absorber, which also acts as an output coupler at the same time. The repetition rate of the Q-switched envelope increased from 25 to 40 kHz as the pump power increased from 2.2 to 6.9 W. The mode-locked pulses inside the Q-switched pulse envelope had a repetition rate of 714 MHz. A maximum average output power of 770 mW was obtained.     

Laser ranging based on electro-optic switch

Based on electro-optic switch effect in crystal, a novel laser ranging method is proposed. CW-laser emitted by laser transmitter propagates forward to the measured target, after being reflected by the target, and then goes back to the transmitter. Close to the transmitter, a special mono-block LiNbO₃ crystal is added into the round-trip light beams. High-voltage pulses with the sharp enough changes in rising edges are loaded on the crystal. Based on electro-optic effect, double refraction and internal double reflection effect in crystal, the crystal cuts off the round-trip light beams, and reflects a light pulse cut out by the crystal to a detector aside from the original beam path. The pulse width T is the period that laser propagates forward and back between the crystal and the target. The feasibility of the new idea is proved by our experiments and a brand-new way for the laser ranging is provided.     

Effect of magnetic field on the TC and magnetic properties for the aligned MnBi compound

In the compound MnBi, a first-order transition from the paramagnetic to the ferromagnetic state can be triggered by an applied magnetic field and the Curie temperature increases nearly linearly with an increase in magnetic field by ∼2 K/T. Under a field of 10 T, T_C increases by 20 and 22 K during heating and cooling, respectively. Under certain conditions a reversible magnetic field or temperature induced transition between the paramagnetic and ferromagnetic states can occur. A magnetic and crystallographic H-T phase diagram for MnBi is given. Magnetic properties of MnBi compound aligned in a Bi matrix have been investigated. In the low temperature phase MnBi, a spin-reorientation takes place during which the magnetic moments rotate from being parallel to the c-axis towards the basal plane at ∼90 K. A measuring Dc magnetic field applied parallel to the c-axis of MnBi suppresses partly the spin-reorientation transition. Interestingly, the fabricated magnetic field increases the temperature of spin-reorientation transition T_s and the change in magnetization for MnBi. For the sample solidified under 0.5 T, the change in magnetization is ∼70% and T_s is ∼91 K.     

Study on anti-emission materials for non-emitting grid applications in microwave power tubes

Hafnium and platinum were deposited onto molybdenum grids by ion-beam assisted deposition method. Electron-emission characteristics from molybdenum grids with Hf and Pt films, which were contaminated by active electron-emission substances (Ba, BaO) of the cathode, were measured using analogous diode method. The surfaces of grids were analyzed by X-ray diffraction. The results revealed that the reaction between BaO and Hf formed BaHfO₃ compound, which greatly reduced the accumulation of BaO on the surface and accordingly decreased grid emission. In contrast, Ba were formed by the decomposition of BaO on the surface of Pt film under high temperature and re-evaporated from its surface, which reduced the active electron-emission substances on the surface of the grid and effectively restrained grid emission. Their mechanisms for grid-emission suppression are discussed and a good method to develop new grid-coating materials is suggested.     

High-throughput screening of fuel cell electrocatalysts

The drawbacks of our earlier report of preparing fuel cell catalyst arrays by borohydride reduction of inkjet prepared arrays of metal salts are discussed along with the need for inclusion of state-of-the-art metrics in all array screening. An alternative method for screening of hydrogen/air cathode catalysts, direct methanol fuel cell (DMFC) anode catalysts, and catalyst loading studies is provided. State-of-the-art Johnson Matthey catalysts were used in control experiments to demonstrate the utility of the array fuel cell for high throughput screening of fuel cell catalysts in the 3-4 mg/cm² range. This report lays out hard learned rules for high throughput screening and demonstrates that the array fuel cell can be used for very precise screening of libraries of membrane electrode assembly (MEA) components without the pitfalls discussed in the introduction.     

Magnetic and electrical transport properties of delta-doped amorphous Ge:Mn magnetic semiconductors

We report on the growth and characterization of delta-doped amorphous Ge:Mn diluted magnetic semiconductor thin films on GaAs (0 0 1) substrates. The fabricated samples exhibit different magnetic behaviors, depending on the Mn doping concentration. The Curie temperature was found to be dependent on both the Mn doping concentration and spacing between the doping layers. A sharp drop in magnetization and rise in resistivity are observed at low temperature in samples with high Mn doping concentrations, which is also accompanied by a negative thermal remanent magnetization (TRM) in the higher temperature range. The temperature at which the magnetization starts to drop and the negative TRM appears show a correlation with the Mn doping concentration. The experimental results are discussed based on the formation of ferromagnetic regions at high temperature and antiferromagnetic coupling between these regions at low temperature.     

Evaluation of gap length fluctuation with harmonic analysis method

Gap length (GL) of reading head is one of the most critical parameters for high-density magnetic recording systems. A novel method is proposed for quantitative evaluation of the GL fluctuation among a batch of magneto-resistive/giant magneto-resistive heads with same structure design. The method works at head-gimbal assembly level and the evaluation can be done with any read/write analysis equipment. The testing process is based on harmonic analysis of the readback signal. The testing system consists of a selected reference head and sample heads for evaluation. A GL variation function is introduced for the evaluation of GL deviation between the reference head and sample head. This method proved to be easy for implementation and results suggest that variation of GL is considerable and has obvious effect on recording performance in high recording density systems.     

Micromagnetic analysis of transition noise for high-density perpendicular recording

In this paper, specific issues related to high-density perpendicular magnetic recording processes, such as transition noise properties and cross-track correlation lengths, were investigated with the help of micromagnetic analysis. The effects of media parameters were taken into consideration, including intergranular exchange coupling, and exchange distribution, irregular grain shapes, magnetization saturation distribution, and anisotropy distribution. The micromagnetic simulation results showed that the effect of anisotropy distribution on transition noise is more significant than magnetization saturation distribution, and it is crucial to reduce this effect to achieve a high signal-to-noise ratio. Additionally, a new method to further estimate the partial erasure threshold was proposed to approximate the partial erasure effects, and the relation between the microtrack jitter and total track jitter was investigated.     

Engineering issue study of triple harmonic method for in situ flying height analysis

In situ flying height testing technology is becoming more and more important in slider–disk interaction analysis and manufacturing quality control of disk drives and head-related components. Triple harmonic method is a quite promising choice for in situ flying height analysis, compared with other in situ methods reported up to now. This paper reports results of investigations on engineering issues of applying triple harmonic method for in situ flying height analysis. The paper reports results of analysis on the effects of various testing conditions on flying height testing repeatability and accuracy. Results suggest that working at reasonable high channel density and working on the ratio between third and first harmonics will be an advantage in terms of both flying height testing sensitivity and testing repeatability. Comparing with media thickness effect, the gap-length variation among different heads will be important if it is to study flying height difference among different heads and the testing is at high channel density. Also, it is suggested to work at AC erased track, in order to reduce the non-linearity caused by hard transition.     

Magneto resistance due to domain wall scattering and magneto size effect of thin Ni and Co films at low temperatures

Nickel and cobalt films illustrate alternative Bloch lines with cap switches. The strip magnetic domains become zigzag and bubbling cells for Ni and Co films, respectively, under an external field of 1.5 T. The magnetoresistances (MR) for currents parallel (CIW) to the domain walls is 15% less than those of the perpendicular (CPW) case. We also studied the magneto size effect by applying the magnetic field normal to the surface, from which the Sondheimer oscillation appears attributing to periodic striking of the surface for electrons traveling in circular motion on a plane canting to the surface. The experiments can be expressed by the magneto size effect inherited with very small specularity parameters.