Emulsion stability and potassium leakage in emulsion liquid membrane systems

Potassium leakage was studied in liquid membrane systems containing various emulsifiers and compared with emulsion, stability in the storage test. The effects of various parameters upon emulsion stability and the leakage of standard traces are discussed. The transfer of cations can be caused by emulsion breaking, by transport with the specific carrier and/or with surfactants used as emulsifiers. The latter case becomes especially important when hydrophilic surfactants, e.g. ones containing polyoxyethylene chains, are present in liquid membranes. In systems containing hydrophobic emulsifiers the transfer of potassium is relatively low. In each case considered the effect of emulsifiers upon the transfer of the standard tracer should be checked prior to using the leakage test to characterize emulsion stability.     

DTA determination of the anhydrite content in rock salts

The DTA method was used to determine the phase diagram of the NaCl-CaSO₄ system over the range 0.55 wt.% of CaSO₄ in air atmosphere. The effects of SiO₂, CaCO₃ and Fe₂O₃ on the melting temperatures of pure NaCl and the eutectic were determined. On the basis of the above temperatures, a method of quantitative determination of the anhydrite content in rock salts has been developed.

---

Zusammenfassung DTA wurde benutzt, um in Luft im Bereich 0 bis 55,0 Gew.% CaSO₄ das Phasendiagramm des Systemes NaCl-CaSO₄ zu bestimmen. Es wurde auch der Einfluß von SiO₂, CaCO₃ und Fe₂O₃ auf die Schmelztemperatur von reinem NaCl bzw. des Eutektikums bestimmt. Auf der Grundlage obiger Temperaturen wurde eine Methode zur quantitativen Bestimmung des Anhydritgehaltes in Steinsalzen entwickelt.

---

- 0–55,0 . , . , ( ) .

     

Extension of the measuring range of balances

The basic principle of comparing the sample mass with the mass of a reference body in equilibrium gives the equal-armed beam balance a unique accuracy. Main parameters characterising the suitability of the instrument are measuring range, resolution and relative sensitivity (resolution/maximum load). The historical development of the values of these parameters achieved depended strongly on the practical need in those times. Technically unfavourable scales of the oldest Egyptian dynasties (~3000 BC) could resolve mass differences of 1 g and had a relative sensitivity of at least 10^–3. More sophisticated instruments from the 18^th Dynasty (~1567–1320 BC) achieved a relative sensitivity of 10^–4 independent of the size of the instrument. In 350 BC Aristotle clarified the theory of the lever and at about 250 BC Archimedes used the balance for density determinations of solids. The masterpiece of a hydrological balance was Al Chazini’s 'Balance of Wisdom’ built about 1120. Its relative sensitivity was 2⋅10^–5. Real progress took place when scientists like Lavoisier (1743–1794) founded modern chemistry. At the end of the 19^th century metrological balances reached a relative sensitivity of 10^–9 with a maximum load of several kilogrammes. That seems to be the high end of sensitivity of the classical mechanical beam balance with knife edges. Improvements took place by electrodynamic compensation (Emich, Gast). In 1909 Ehrenhaft and Millikan could weigh particles of 10^–15 g by means of electrostatic suspension. In 1957 Sauerbrey invented the oscillating quartz crystal balance. By observing the frequency shift of oscillating carbon nanotubes or of silica nanorods, masses or mass changes in the attogram or zeptogram have been observed recently.     

Concentration and clean-up of trace hydrocarbons from atmospheric particulate matter

Summary The aim of this work is to establish the best conditions for concentration and purification steps in the trace analysis of aliphatic and polycyclic aromatic hydrocarbons (PAH) from atmospheric particulate matter by gas chromatography-flame ionisation detection (GC-FID) and high performance liquid chromatography with ultraviolet and fluorescence detection (HPLC-UV-FL). The best results for the more volatile compound were obtained with a combination of rotary evaporation and a stream of nitrogen (near to 100% for aliphatic hydrocarbons and from 70 to 105% for PAH). Two types of solid phase extraction (SPE)cartridges (Supelclean ^tm LC-Silica SPE tubes and Sep-Pak^? Plus silica cartridges) and glass column were examined for the purification and fractionation step. Blank chromatograms of both types of cartridges analysed by GC-FID made this study difficult, because a PSS (programmed split-splitless) injector was employed thereby increasing the sensitivity. This problem was not observed in the HPLC-UV-FL blank chromatograms of these cartridges. Glass columns filled with silica and alumina were chosen because no interference was found in the GC-FID blank chromatograms and the best recoveries in the fractionation of both aliphatic hydrocarbons and PAH were achieved. This is especially important when aliphatic hydrocarbons concentrations are lower than 1 μg mL⁻¹. Finally, the selected conditions were applied to the analysis of hydrocarbons in real atmospheric particulate samples.     

Diffusion characteristics of a T-type microchannel with different configurations and inlet angles.

A series of symmetrical and asymmetrical microfluidic T-sensors with different inlet angles were fabricated to study the mixing characteristics of a T-type microstructure for generating concentration gradient. Computational fluid dynamics (CFD) simulations showed that the concentration gradient, transition zone and diffusion length were different for various configurations and inlet angles. Quick mix and sharp concentration gradient occurred in the asymmetrical structure with large inlet angle. The observed concentration gradients in the fabricated microchannel were consistent with the theoretical prediction. In this microstructure, stagnant zone and z-direction diffusion also affected the concentration gradient. Based on the simulation results, the microfluidic structure was optimized to generate desired concentration gradient for a cell-based study.     

Comments on surface structure analysis by water and nitrogen adsorption

Specific surface area and pore size distribution are determined usually from adsorption isotherms at low temperatures using nitrogen or noble gases. These are not absolute parameters and the measuring methods are fraught with serious difficulties. General problems of sorption measurements and recent developments are discussed. To obtain information for practical purposes these measurements need to be supplemented by investigations of the sorbate/sorbent system used in practice. Results of the measurement of nitrogen and water vapour adsorption on different materials are compared. This revised version was published online in July 2006 with corrections to the Cover Date.     

Synthesis and characterization of metal polycarboxylates constructed from lanthanides(iii) and 1,2,4,5-benzenetetracarboxylic acid

The complexes of yttrium(III) and lanthanides(III) with 1,2,4,5-benzenetetracarboxylic acid were prepared as crystalline solids of the general formula Ln₄(C₁₀H₂O₈)₃⋅14H₂O. They are insoluble in water. On heating in air or inert gas atmosphere all compounds lose water molecules; next anhydrous compounds decompose to oxides. The yttrium complex and heavy lanthanide (from Ho to Lu) ones crystallize in monoclinic crystal system. The dehydration does not change the crystal structure of the compounds.