What Oxidation State of Iron Determines the Amethyst Colour?

A colourless quartz crystal doped with ⁵⁷Fe³⁺ was obtained by hydrothermal synthesis in an NH₄F solution. The crystal was transformed into violet amethyst by gamma-irradiation. The change in colour was accompanied by changes in the Mössbauer spectrum that can be interpreted as the conversion of trivalent iron into the tetravalent state: Fe³⁺→Fe⁴⁺.

     

Lein?l, Lein?lfirniss und Oelfarben

Ohne Zusammenfassung     

The mechanism of emission in the red photoluminescence band of porous silicon

Porous silicon (PS) exhibits several photoluminescence (PL) bands, whose spectral position and intensity depend strongly on the actual conditions of preparation of PS, its treatment, and subsequent use. The PS PL band peaking at about 1.8 eV and usually assigned to the intrinsic emission of silicon nanocrystals was studied. It was shown that the temperature-induced variation of the PL kinetics in the 80 to 300-K interval follows a complex pattern and depends noticeably on the actual point on the band profile. The temperature behavior of PL decay in the 1.8-eV band is determined by the electron-hole recombination rate within a nanocrystal and the cascade carrier transitions from small to large nanocrystals, with an attendant decrease in energy.     

Effect of short glass fiber on structure and viscoelastic behavior of olefinic polymers synthesized with metallocene catalyst

Several composites were prepared on the basis of an ethylene homopolymer and different copolymers of ethylene and 1‐hexene, synthesized with a metallocene catalyst, as matrices and a content of a 5 wt % of short glass fiber. The effect of the fiber incorporation on the structure and mechanical and viscoelastic behaviors was analyzed for the different samples. The glass fibers induced a slightly higher crystallinity, and the crystallite morphology significantly changed (long spacings and crystal orientation). The incorporation of fibers did not reinforce the different matrices under study at this low content; consequently, the mechanical parameters, such as Young's modulus, yielding stress, and microhardness, were lower in the composites as compared with those values found in the neat polyolefins. The location and apparent activation energies of distinct relaxation processes are also discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1244–1255, 2003     

Optimal entropic uncertainty relation for successive measurements in quantum information theory

We derive an optimal bound on the sum of entropic uncertainties of two or more observables when they are sequentially measured on the same ensemble of systems. This optimal bound is shown to be greater than or equal to the bounds derived in the literature on the sum of entropie uncertainties of two observables which are measured on distinct but identically prepared ensembles of systems. In the case of a two-dimensional Hilbert space, the optimum bound for successive measurements of two-spin components, is seen to be strictly greater than the optimal bound for the case when they are measured on distinct ensembles, except when the spin components are mutually parallel or perpendicular     

Mechanisms for the SAR Imaging of the Ocean

We perform a comparative analysis of two mechanisms for the formation of a synthetic aperture radar (SAR) image of the ocean, which are related to orbital velocities on the surface. It is shown that the mechanism of fluctuations of the effective density of scatterers, which is commonly accepted at present as the physical basis for the SAR diagnostics of roughness, actually works only in the case of a sufficiently flat swell. In the presence of wind roughness, the dominant role is played by another mechanism, namely, fluctuations of the number of surface elements whose images are randomly shifted and superimposed in the image plane due to orbital velocities. In the case of a developed wind roughness propagated in the azimuthal direction, the power contributions of two above-mentioned mechanisms to the SAR imaging of the ocean differ by about two orders of magnitude.     

Sensitivity analysis of an optimized bar-spring model with hill-top branching

Summary Characteristics of optimal solutions under nonlinear buckling constraints are investigated by using a bar-spring model. It is demonstrated that optimization under buckling constraints of a symmetric system often leads to a structure with hill-top branching, where a limit point and bifurcation points coincide. A general formulation is derived for imperfection sensitivity of the critical load factor corresponding to a hill-top branching point. It is shown that the critical load is not imperfection-sensitive even for the case where an asymmetric bifurcation point exists at the limit point.     

Application of a generalized residual model to frequency domain modal parameter estimation

Residuals have long been used in frequency domain parameter estimation methods to model the influence of out-of-band modes but, typically, as a fixed set of no more than two or three terms. Recently, a systematic approach to the use of residual polynomials has led to the development of a generalized residual model. The use of a generalized residual model with rational fraction polynomial frequency domain parameter estimation methods allows the contribution of out-of-band modes to be included without increasing the model order and creating additional computational poles. Of particular interest is the use of the generalized residual for single-degree-of-freedom (s.d.o.f.) techniques, which generally do not consider the residual effects and suffer accordingly. With the use of generalized residuals, it becomes possible to properly account for nearby modes and also extract accurate residues with an s.d.o.f. algorithm. The development of the generalized residual polynomial model is outlined and a new s.d.o.f. frequency domain algorithm with generalized residuals is developed.     

Mechanisms of n‐butanol formation in butyl acrylate latexes

The mechanisms involved in the formation of n‐butanol during the synthesis of butyl acrylate containing latices were investigated. The experimental results showed that neither the hydrolysis of butyl acrylate nor of the ester bond in the butyl acrylate segments of the polymer played a major role in the formation of n‐butanol, which was mainly generated from the polymer backbone, by transfer reactions to polymer chain followed by cyclization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5838–5846, 2007