寄生传输线对PFN-Marx输出波形的影响

紧凑型PFN-Marx脉冲发生器中,级与级之间存在着较大的寄生电容,该电容和PFN节电感构成了寄生传输线。对两种排布方式下的寄生传输线的放电过程进行了简单分析,重点开展了双列排布方式下全电路仿真模拟,对负载类型、寄生电容、负载电感等参数对输出波形的影响进行了计算,得到了二极管负载会在波形前沿上造成下降、寄生电容大小决定振荡频率、负载电感放大振荡幅值等结论。开展的PFN-Marx实验研究也进一步验证了上述分析结果。根据分析,提出了一种有效抑制输出波形振荡的方法,从电路上进行了仿真验证,进一步实验证实了该方法的有效性。     

增量PID算法在某风洞压力控制中的应用改进

本文介绍了风洞高度模拟控制系统的构成和控制原理,根据控制特点选取了增量PID控制算法控制补气调节阀开度,针对直接采用增量PID控制算法对风洞总压控制效果不太理想的问题,分析了影响控制效果的原因,提出了采用超前调节的解决措施,并进行了系统调试。调试结果表明：总压控制精度和稳定过渡时间都有明显改善,为风洞总压控制的改进提供了方法。也为类似大惯性、大滞后特性系统的精确、稳定控制提供了参考。     

基于RBR和PCA的2.4米风洞故障诊断系统应用研究

为解决2.4米风洞试验装备的故障监测与诊断（FDD）问题,设计了一种基于规则推理（RBR）和主元分析（PCA）的并行故障诊断系统。对试验流程和因果关系较强的单一装备故障,采用RBR诊断方法;而对控制过程和重要传感器的故障,通过构建PCA模型,根据平方预报误差（SPE）实现系统故障的诊断。运行效果表明：该系统实时性好、诊断结果与实际相符合、且对过程故障具有较强的针对性。     

The optical properties of planar waveguides in LiB3O5 crystals formed by Cu implantation

A planar optical waveguide has been formed in a LiB₃O₅ crystal using 6.0 MeV Cu⁺-ions with a dose of 1 × 10¹⁵ ions/cm² at room temperature. Possible propagating modes were measured at a wavelength of 633 nm using the prism-coupling method. The refractive index profiles of the waveguide were reconstructed by an effective refractive index method and the beam propagation method was used to investigate the properties of the propagation modes in the formed waveguide. The results suggest that the fundamental TE₀ and TM₀ modes may be well-confined and propagate a longer distance inside the waveguide. The implantation process was also simulated using the transport of ions in matter code (TRIM), which indicates that the nuclear energy deposition may be the main factor for the refractive index change.     

光纤光栅腐蚀传感器

提出了一种测量钢筋腐蚀的新型传感器.这种传感器将光纤光栅拉伸后固定在圆形钢筋的表面,在钢筋被腐蚀后,光纤光栅所受到的拉伸应变将被释放,光纤光栅的反射光波长发生变化,通过测量光纤光栅的波长就可以测得钢筋腐蚀程度.这种传感器测量准确度优于±0.1 μm,测量范围约12 μm,可用于混凝土结构中钢筋腐蚀的早期监测.     

Effect of cooling rate on microstructure of friction-stir welded AA1100 aluminum alloy

In this work, the microstructural changes occurring during cooling of friction-stir welded aluminum alloy AA1100 were evaluated. To this end, friction-stir welding (FSW) was performed in a wide range of cooling rates of 20–62 K/s and the evolved microstructures were studied by using electron backscatter diffraction. Below 0.6 T_m (T_m being the melting point), the stir zone material was found to experience no significant changes during cooling. At higher FSW temperatures, however, notable changes occurred in the welded material, including grain growth, sharpening of texture, reduction of the fraction of high-angle boundaries and material softening.     

处理污泥焦颗粒内部孔结构在燃烧过程中变化

在管式炉反应器中进行了1种污泥定温燃烧试验,进行了5个不同燃烬率样品的液氮静态容量法等温物理吸附试验.发现不同燃烬率的污泥样品孔分布特性相似,其孔系统可能主要是由一端封闭的不透气的孔构成;随着燃烬率的增加,比表面积、平均孔径和孔体积等参数变化不同;样品颗粒内孔表面分形维数随燃烬率的增长呈先降低再升高的趋势.     

奇相干光源的测量设备无关量子密钥分配研究

刻画了奇相干光源的光子数分布特征,研究了奇相干光源下诱骗态测量设备无关量子密钥分配系统的密钥生成率与安全传输距离的关系,推导了奇相干光源下的计数率下界和误码率上界.仿真结果表明,奇相干光源光子数分布中多光子脉冲的比例低于弱相干光,可以有效提高诱骗态测量设备无关密钥分配系统的最大安全通信距离,为实用的量子密钥分配实验提供了重要的理论参数.     

Suppression of thermoelastic damping in MEMS beam resonators by piezoresistivity

Microelectronic mechanical (MEM) beam resonators with high quality factors are always preferred in practical applications. As one of the damping sources, thermoelastic damping (TED) caused by irreversible heat flows is usually considered as an upper limit of the overall damping effect. A new method is proposed in this work to compensate TED by taking advantage of the piezoresistive effect. Such a method is implemented by applying an electrostatic field along the beam length with a negative piezoresistive coefficient. During a resonance, the stretched part of the beam generates a higher electrical power density and thus a higher temperature, while the compressed region leads to a lower temperature. Such a temperature distribution is opposite to the temperature change caused by the thermoelastic effect. The working principle is described by a set of coupled differential equations, which are subsequently solved by the finite element method. The result indicates that the TED in the beam resonators can be completely compensated when the strength of electrical field is tuned to a critical value, namely CEF. The value of the CEF is further analyzed by a series of parametric studies on various material properties and geometric factors.