强激光能源系统的Marx触发器

针对强激光能源系统对Marx触发器的输出性能和可靠性要求,介绍了一种六级的Marx触发器。通过采用多级低电感脉冲形成电路获得了高幅值、陡前沿的输出脉冲,运用实验与概率分析相结合的方法,确定了它的工作参数。实验研究结果表明:这种Marx触发器的误触发率和触发气体开关成功率均符合两参数的威布尔概率分布;当欠压比为65%、工作电压为13.5 kV、工作气压（绝压）为0.35 MPa时,能输出幅值120 kV、前沿20 ns的电压脉冲;该触发器能同时满足误触发率低于0.000 1%,正常触发成功率高于99.999 9%的技术要求。经过长时间现场运行测试,Marx触发器工作良好,无异常现象。     

Surface modification of poly(styrene-b-(ethylene-co-butylene)-b-styrene) elastomer via photo-initiated graft polymerization of poly(ethylene glycol)

Poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS) copolymer biomedical elastomer was covalently grafted with poly(ethylene glycol) methyl ether methacrylate (PEGMA) via a photo-initiated graft polymerization technique. The surface graft polymerization of SEBS with PEGMA was verified by ATR-FTIR and XPS. Effect of graft polymerization parameters, i.e., monomer concentration, UV irradiation time and initiator concentration on the grafting density was investigated. Comparing with the virgin SEBS film, the PEGMA-modified SEBS film presented an enhanced wettability and a larger surface energy. Besides, the surface grafting of PEGMA imparted excellent anti-platelet adhesion and anti-protein adsorption to the SEBS surface.     

Design for broadband high-efficiency grating couplers

In this Letter, we propose general optimization methods to design broadband high-efficiency grating couplers for planar waveguides. We attribute the coupling bandwidth to the mismatch of effective indices between the diffracted beam and the actual grating structure around the operation wavelength for fiber to waveguide excitation. The coupling bandwidth formula is deduced. A simple parameter-separate optimization procedure is proposed for general layered grating couplers for high coupling efficiency. Using our principle, we optimized a grating coupler for a horizontal slot waveguide operating at wavelength 1.55 μm for TM polarization. The grating coupler has 1 dB bandwidth of 60 nm and coupling efficiency of 65% with incident light from single-mode optical fiber (SMF) at 8°.     

锑烯吸附金属Li原子的密度泛函研究

锑烯(antimonene)是继石墨烯和磷烯之后出现的新型二维材料,在锂离子电池等领域受到关注.本文基于第一性原理的密度泛函理论,计算研究了锑烯对Li原子的吸附特性,包括Li原子的最稳定吸附构型、吸附密度以及吸附Li原子的扩散路径.结果表明:Li原子最稳定的吸附位置位于谷位,即底层Sb原子之上、顶层三个Sb原子中心位置,吸附能为1.69 eV,吸附距离为2.81?;能带计算发现,锑烯为带隙宽度1.08 eV的间接带隙半导体,吸附Li原子后费米能级上升进入导带,呈现出金属性;原子分波态密度分析发现, Sb原子的p电子态和Li原子的p和s电子态形成明显的共振交叠,表现出杂化成键的特征;随着吸附Li原子数量增加,锑烯晶格结构和电子结构发生较大变化.通过微动弹性带方法计算发现, Li原子在锑烯表面的扩散势垒为0.07 eV,较小的势垒高度有利于快速充放电过程.     

CH3OH在ZnO(0001)表面的光催化解离

本文利用266 nm波长的激光及程序升温脱附的方法研究了甲醇在ZnO(0001)表面的光催化反应. TPD结果显示部分的CH₃OH以分子的形式吸附在ZnO(0001)表面,而另外一部分在表面发生了解离. 实验过程中探测到H₂,CH₃^·,H₂O,CO,CH₂O,CO₂和CH₃OH这些热反应产物. 紫外激光照射实验结果表明光照可以促进CH₃OH/CH₃O^·解离形成CH₂O,在程序升温或光照的过程中它又可以转变为HCOO^-. CH₂OH_Zn与OH_ad反应在Zn位点上形成H₂O分子. 升温或光照都能促进CH₃O^·转变为CH₃^·. 该研究对CH₃OH在ZnO(0001)表面的光催化反应机理提供了一个新的见解.     

悬浮液进样—火焰原子吸收光谱法测定玉米中的锌和铁

本文提出了一种悬浮液进样－火焰原子吸收光谱法测定玉米面中锌,铁的新方法。将玉米面悬浮于琼脂胶体中,直接喷入空气－乙炔火焰中,用标准加入法测定,测定结果与灰化法一致。方法简便,快速。     

Gate Tunable Supercurrent in Josephson Junctions Based on Bi_2Te_3 Topological Insulator Thin Films

We report transport measurements on Josephson junctions consisting of Bi_2Te_3 topological insulator(TI) thin films contacted by superconducting Nb electrodes.For a device with junction length L=134 nm,the critical supercurrent I_c can be modulated by an electrical gate which tunes the carrier type and density of the TI film.I_c can reach a minimum when the TI is near the charge neutrality regime with the Fermi energy lying close to the Dirac point of the surface state.In the p-type regime the Josephson current can be well described by a short ballistic junction model.In the n-type regime the junction is ballistic at 0.7 K T 3.8 K while for T 0.7 K the diffusive bulk modes emerge and contribute a larger I_c than the ballistic model.We attribute the lack of diffusive bulk modes in the p-type regime to the formation of p-n junctions.Our work provides new clues for search of Majorana zero mode in TI-based superconducting devices.     

微腔内气体抽离的多尺度模拟与分析

基于适用于整个克努森数范围的流动理论,建立了去除惯性约束聚变实验中靶丸内空气的理论模型,并设计实验验证了此模型的可靠性。物理实验要求靶丸内空气浓度低于10×10⁻⁶,数值模拟了去除靶丸内空气的过程,重点分析了靶丸内空气浓度、压力与除气时间的关系。计算并比较了单管路一次抽气法、单管路循环抽气法与双管路流洗法三种去除靶丸内空气方法的时间成本。数值计算结果表明：单管路一次抽气法中,靶丸上的微通道的存在对去除靶丸内空气所需时间的影响不可忽略,在考虑靶丸上微通道与充气管的情况下,需要1961.77 h才能使靶丸内的空气浓度达到标准。单管路循环抽气法中,抽气次数与单次抽气程度会影响去除靶丸内空气所需总时间,在单次抽气程度值取最优的情况下,采用充三次,抽四次的方案可使达标总时间减少至1 h左右,此方案下单次充气和抽气时间分别为6 min和10 min。而采用双管路流洗法则仅需11 min便可使靶丸内空气浓度达标。     

稀土与半胱氨酸、枸橼酸钠三元配合物的合成和抗凝血作用研究

用氯化稀土与枸橼酸钠、半胱氨酸制备了三种组成恒定的稀土三元配合物. 通过元素分析、红外光谱、X射线衍射、摩尔电导、TG-DTA和1H NMR对配合物进行了表征, 并进行了抗凝血试验, 表明稀土三元配合物具有优良的抗凝血性质.     

Optimal switching from recording to fixing for high diffraction from a LiNbO3:Ce:Cu photorefractive nonvolatile hologram

An oscillatory characteristic of diffraction is observed as a result of strong beam coupling in a weakly oxidized LiNbO3:Ce:Cu crystal during the recording step in the production of nonvolatile photorefractive holograms. On this basis the optimal switching time from the recording step to the fixing step for high diffraction of a fixed hologram is studied. It is shown that switching after the first diffraction maximum leads theoretically to fixed diffraction of as much as 100% with a suitable switching time. Both an experimental demonstration and a theoretical simulation are presented.