溶胶-凝胶制备技术与新型催化材料Ⅲ.溶胶粒子表面修饰方法制备催化膜

提出用溶胶粒子表面修饰方法，结合溶胶凝胶技术制备无机催化膜．该方法的基本原理是利用合适的金属配合物在胶粒表面的吸附作用，经溶胶凝胶过程，将活性组分结合到无机膜中．实验测定结果表明：（ＮｉＥＤＴＡ）２－，ＶＯ－３，ＭｏＯ２－４，（Ｐｄ（ＮＨ３）４）２＋，ＰｄＣｌ２－４，ＰｔＣｌ２－６和ＲｈＣｌ３－６可用来修饰ＡｌＯＯＨ溶胶．以Ｐｄ／γＡｌ２Ｏ３催化膜的制备为例，经三次溶胶凝胶过程，可制得无裂缺的厚度为９μｍ的Ｐｄ／γＡｌ２Ｏ３催化膜，膜材料的平均孔直径为６ｎｍ，Ｐｄ被均匀地分布在膜的顶层，其平均粒径为２３ｎｍ．     

F／Cl比与Eu~（2＋）：BaFCl中F色心的浓度和光激励截面的关系

研究了Ｅｕ（２＋）：ＢａＦｘＣｌ２在紫外线辐照下的光激励发光。通过改变激励方式及激励光的扫描方向，给出了Ｅｕ（２＋）：ＢａＦｘＣｌ２－ｘ光激励发光过程中，两种Ｆ色心的浓度比值与光激励截面比值的测定方法。利用这种测定方法，进一步研究了两种Ｆ色心的浓度比值和光激励截面比值与Ｆ／ＣＩ比值的关系。     

Fourier regularization for a backward heat equation

In this paper a simple and convenient new regularization method for solving backward heat equation—Fourier regularization method is given. Meanwhile, some quite sharp error estimates between the approximate solution and exact solution are provided. A numerical example also shows that the method works effectively.     

Crystallographic report: Bis(norfloxacin)dilead(II) tetranitrate, [Pb2(H‐Norf)2(ONO2)4]

The centrosymmetric binuclear structure of [Pb₂(H‐Norf)₂(ONO₂)₄]shows the geometry around each lead(II) atom to be distorted trigonal bipyramidal with Pb–O distances ranging from 2.357(3) to 2.769(4) Å. Copyright © 2003 John Wiley & Sons, Ltd.     

硫酰胺的快速分析（Ⅱ） 

硫酰胺生产过程中副产的大量氯化铵要干扰硫酰胺的测定，采用四苯硼钠将全部氯化铵呈沉淀析出，再用次溴酸钠把滤液中的硫酰胺分解成氮气，测其体积，计算出硫酰胺的含量。对样品进行测定的结果表明，该法重现性好、准确度高、分析周期在３５ｍｉｎ内，相对误差在±１％以内。     

Application of novel SIMS technique for imaging the active sites of oxygen reduction at the SOFC cathode/electrolyte interfaces

The oxygen reduction active sites were visualized around the O₂/SOFC cathode/electrolyte triple phase boundaries (TPB) by the¹⁶O/¹⁸O exchange techniques and secondary ion mass spectrometry (SIMS) analysis. The higher¹⁸O concentration is observed on the cathode top surfaces (La_0.9Sr_0.1MnO₃-mesh, Au-mesh, and Ag-porous), which suggested the promotion of oxygen adsorption and oxygen surface exchange at the cathode. The oxygen diffusion through the bulk of cathode occurred at the La_0.9Sr_0.1MnO₃-mesh and the Ag-porous cathodes, not at the Au-mesh cathode. On the YSZ surfaces after removing the cathode, the active sites for oxygen incorporation were analyzed by SIMS. The active sites for oxygen incorporation were at the La_0.9Sr_0.1MnO₃/YSZ interface as well as the TPB. On the other hand, the active sites for oxygen incorporation are limited to the TPB in the case of the Au-mesh removed YSZ surface. From the SIMS analysis, the expansion of the active sites for oxygen incorporation is less than a few μm from the TPB lines. Paper presented at the 8th EuroConference on Ionics, Carvoeiro, Algarve, Portugal, Sept. 16–22, 2001.     

Sensitive monitoring of humic acid in various aquatic environments with acidic cerium chemiluminescence detection.

In this research, a simple, sensitive chemiluminescence (CL) method for the determination of humic acid (HA) in water samples was first developed based on the redox reaction between humic acid and cerium(IV) in the acidic condition. Different with the former redox CL reaction which occurred in alkaline solution, no enhancers were needed and neither precipitation nor a second contamination would occur in the present CL system. Comparing with other spectrometric methods, we find that the proposed analysis system had better applicability and accuracy. Under the optimal experiment conditions, the CL peak height was linear with the concentration of HA in the range of 0.03 to 10.0 microg mL(-1). The detection limit is 0.01 microg mL(-1) (S/N = 3), and the relative standard deviation was 2.3% for 0.5 microg mL(-1) HA solution with eleven repeated measurements. The present CL method was successfully applied to the determination of HA in tap water, spring water and river water samples with good recovery from 90.0 to 110.0%. A possible CL mechanism was proposed based on the results of UV and fluorescence spectrometry and the CL spectrum of HA. It was speculated that the semi-quinone radicals in the excited state were the emitters.     

VO2-Based Infrared Microbolometer Array

V0₂-based thin film materials on silicon substrates are fabricated by ion beam sputtering and a post-annealing which is different from the conventional fabricating method. An infrared linear microbolometer array with 128 pixels is prepared using as-deposited vanadium dioxide thin films. Optical and electrical properties for V0₂-based microbolometer array are tested.