厚度诱导的YBa2Cu3O7-δ超导薄膜剩余应力及临界电流变化

本文通过脉冲激光沉积法制备了不同厚度(80nm、320nm、1000nm和2000nm)的YBa2Cu3O7-δ(YBCO)超导薄膜,对它们的剩余应力和临界电流特性进行了对比研究.通过系列的激光显微Raman光谱和磁化曲线测量分别获得了薄膜剩余应力和磁化临界电流密度(Jc)对薄膜厚度的依赖关系.结果显示超导薄膜内剩余应力越小,Jc越高.对于中等厚度的薄膜样品(320nm和1000nm),其膜内剩余应力较小,同时由其特征的磁通匹配场大小推知在该厚度范围内的样品具有较高的线性缺陷密度,从而显示出较高的Jc值.     

Vaidya-Bonner黑洞的费米子隧穿

运用费米子隧穿的理论,对Vaidya-Bonner黑洞的费米子Hawking辐射进行研究.使用随动坐标变换,并假设γ^μ矩阵的一个合理形式,从而得到了Vaidya-Bonner黑洞的自旋为1/2的粒子的隧穿辐射行为. 关键词： Vaidya-Bonner黑洞 Dirac方程 Hawking辐射 费米子隧穿     

Thermal annealing behaviour of Al/Ni/Au multilayer on n-GaN Schottky contacts

Recently GaN-based high electron mobility transistors (HEMTs) have revealed the superior properties of a high breakdown field and high electron saturation velocity. Reduction of the gate leakage current is one of the key issues to be solved for their further improvement. This paper reports that an Al layer as thin as 3 nm was inserted between the conventional Ni/Au Schottky contact and n-GaN epilayers, and the Schottky behaviour of Al/Ni/Au contact was investigated under various annealing conditions by current--voltage (I--V) measurements. A non-linear fitting method was used to extract the contact parameters from the I--V characteristic curves. Experimental results indicate that reduction of the gate leakage current by as much as four orders of magnitude was successfully recorded by thermal annealing. And high quality Schottky contact with a barrier height of 0.875 eV and the lowest reverse-bias leakage current, respectively, can be obtained under 12 min annealing at 450°C in N₂ ambience.     

Developing a wireless sensing method for the measurement of gamma radiation dose based on the polymerization of acrylamide

A wireless sensing method for the measurement of gamma radiation dose has been developed based on the fact that gamma rays can initiate the polymerization of acrylamide, which causes an increase in solution viscosity that can be detected with a wireless magnetoelastic sensor. The magnetoelastic sensor is able to wirelessly detect the resonance frequency shifts of a magnetoelastic foil in response to changes in solution viscosity. There is a linear relationship between the resonance frequency shift and gamma radiation dose in the range of 0–50 Gy (under optimal conditions) with a detection limit of 0.25 Gy. This method has the advantage of providing real-time, continuous measurement in situ. The method has been used successfully to determine the gamma radiation dose in real exposure scenarios, with satisfactory results.     

Phase transition,dielectric and piezoelectric properties of NaNbO3–Bi0.5Li0.5TiO3 lead-free ceramics

Lead-free ceramics (1?x)NaNbO₃–xBi_0.5Li_0.5TiO₃ have been fabricated by an ordinary sintering technique, and their electric properties and temperature characteristics have been studied. All the ceramics possess a perovskite structure with orthorhombic symmetry, indicating that (Bi_0.5Li_0.5)TiO₃ diffuses into NaNbO₃ lattices to form a new solid solution. A low (Bi_0.5Li_0.5)TiO₃ doping level transforms the NaNbO₃ ceramics from antiferroelectric to ferroelectric. The ceramics with x ≤ 0.075 are normal ferroelectric, and the ferroelectric-paraelectric phase become diffusives with the doping level of Bi_0.5Li_0.5TiO₃ increasing. As x increases, the Curie temperature of the ceramics decreases linearly, while the relative permittivity ε_r increases. 0.925NaNbO₃–0.075(Bi_0.5Li_0.5)TiO₃ ceramic exhibits the relatively large piezoelectric constant (d₃₃ = 58 pC/N), high Curie temperature (T_C = 228 °C) and good temperature stability, suggesting that the ceramics are one of new possible candidates for lead-free piezoelectric materials.     

LTD模块串联装置中部分模块不工作时的输出性能

基于10级模块串联的1 MV快脉冲直线型变压器驱动源装置,分别开展了1～3个模块在不充电或不触发时装置的整体输出参数测试。结果表明,在二极管负载阻抗基本不变的情况下,装置输出电流和电压降低的数值约为故障模块数与总模块数的比值。与所有模块正常工作时相比,脉冲上升时间分别增加10,22和32 ns,脉冲宽度分别增加13,23和48 ns。根据电路分析以及模块实际电参数建立了装置的等效电路模型,模拟得到的不同数量模块不工作时的输出电压变化趋势与实验结果基本一致,并利用电路模型对故障模块中开关两端的电压进行了模拟和分析。     

Simulation and fabrication of carbon nanotubes field emission pressure sensors

A novel field emission pressure sensor has been achieved utilizing carbon nanotubes (CNTs) as the electron source. The sensor consists of the anode sensing film fabricated by wet etching process and multi-wall carbon nanotubes (MWNTs) cathode in the micro-vacuum chamber. MWNTs on the silicon substrate were grown by thermal CVD. The prototype pressure sensor has a measured sensitivity of about 0.17-0.77 nA/Pa (101-550 KPa). The work shows the potential use of CNTs-based field-emitter in microsensors, such as accelerometers and tactile sensors.     

Investigation of chemical decomposition of CCl4 on TiO2 near room temperature

Dissociative adsorption of CCl₄ on TiO₂ at 35 °C has been studied by Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and electron spin resonance. CCl₄ decompose to form CO, CO₂, and CO₃ on the surface, at such a low temperature, in which CO₂ formation is not from CO oxidation on TiO₂, but CO₃ can be produced by CO and CO₂ adsorption. The Cl generated from CCl₄ decomposition is left on the surface and bonded to titanium ions. Mineralization of CCl₄ on TiO₂ involves the lattice oxygens. Thermodynamical driving force and possible reaction routes for CO and CO₂ formation in the CCl₄ decomposition on TiO₂ are discussed.     

A New theory for evaluating the number density of inclusions in films

A new formulation derived from thermal characters of inclusions and host films for estimating laser induced damage threshold has been deduced. This formulation is applicable for dielectric films when they are irradiated by laser beam with pulse width longer than tens picoseconds. This formulation can interpret the relationship between pulse-width and damage threshold energy density of laser pulse obtained experimentally. Using this formulation, we can analyze which kind of inclusion is the most harmful inclusion. Combining it with fractal distribution of inclusions, we have obtained an equation which describes relationship between number density of inclusions and damage probability. Using this equation, according to damage probability and corresponding laser energy density, we can evaluate the number density and distribution in size dimension of the most harmful inclusions.     

Friction phenomena in a two-dimensional Frenkel-Kontorova model

By using the molecular dynamic simulation method with a fourth-order Runge--Kutta algorithm, a two-dimensional dc- and ac-driven Frenkel--Kontorova (FK) model with a square symmetry substrate potential for a square lattice layer has been investigated in this paper. For this system, the effects of many different parameters on the average velocity and the static friction force have been studied. It is found that not only the amplitude and frequency of ac-driven force, but also the direction of the external driving force and the misfit angle between two layers have some strong influences on the static friction force. It can be concluded that the superlubricity phenomenon appears easily with a larger ac amplitude and lower ac frequency for some special direction of the external force and misfit angle.