Dimensional variation in production of high-aspect-ratio micro-pillars array by micro powder injection molding

Micro powder injection molding (μPIM) is one of the potential processes for the mass production of metallic microstructures and micro components. Here, μPIM is the miniaturization of conventional PIM, which involves four processing steps: mixing, injection molding, debinding and sintering. This paper looks into the feasibility and effectiveness of μPIM as a key mass production process for the fabrication of metallic micro components. For it to be an effective re-production process, it is imperative to examine how well parts can be duplicated/fabricated from a master mold. In this work, the dimensional variation of high-aspect-ratio micro-pillars arrays, in particular the dimensional shrinkage, global warpage, and surface roughness at each stage of the μPIM process for a range of molding pressures, are quantified and compared in detail. The sensitivity of the dimensional variation of the microstructures to the packing pressure is reported. The mechanism behind the dimensional variation is analyzed. PACS 81.20.Ev; 81.20.Hy; 81.70.Fy; 07.60.Ly; 81.05.-t     

Effect of Al content on the properties of Cr1−xAlxC films prepared by RF reactive magnetron sputtering

Cr_1−xAl_xC films were deposited on high-speed steel by RF reactive magnetron sputtering. In this study, we aimed to identify the effect of the Al content on the properties of Cr_1−xAl_xC films. We found that Cr_1−xAl_xC films exhibited a fine columnar grain microstructure with some special characteristics, such as high hardness of Hv 1426, a low friction coefficient of 0.29, and a large contact angle of 90° for x = 0.18. Furthermore, an increase in Al content resulted in a decrease in film hardness and an increase in contact angle. Moreover, on annealing at 923 K, the mechanical properties of the films improved and a dense protective film of complex Cr₂O₃ and Al₂O₃ oxides was formed on the surface for better wear resistance, which will ultimately increase the lifetime of the high-speed steel substrate.     

Enhancement of coercivity with reduced grain size in CoCrPt film grown by pulsed laser deposition

We report a pulsed laser deposition (PLD) growth of VMn/CoCrPt bilayer with a magnetic coercivity (H_c) of 2.2 kOe and a grain size of 12 nm. The effects of VMn underlayer on magnetic properties of CoCrPt layer were studied. The coercivity, H_c, and squareness, S, of VMn/CoCrPt bilayer, is dependent on the thickness of VMn. The grain size of the CoCrPt film can also be modified by laser parameters. High laser fluence used for CoCrPt deposition produces a smaller grain size. Enhanced H_c and reduced grain size in VMn/CoCrPt is explained by more pronounced surface phase segregation during deposition at high laser fluence.     

一种新的磷化铟复合沟道高电子迁移率晶体管小信号物理模型

针对磷化铟(InP)复合沟道高电子迁移率晶体管(HEMT)的特点，对常规单沟道HEMT的小信号物理模型进行了修正，提出了一种新的用于复合沟道HEMT的小信号物理模型，用商用器件模拟软件ISE(integrated systems engineering)对其进行了仿真验证，对比了实测和仿真的I-V特性及转移特性曲线，重点研究了在InGaAs/InP双层沟道中考虑量子效应后的电场和电流密度随着不同栅电压的变化趋势，研究结果表明，由于在沟道中存在量子效应，在栅下靠源端低电场区域，电流主要分布在InGaAs沟道 关键词： 高电子迁移率晶体管 复合沟道 物理模型 磷化铟     

KNSBN晶体猫式互抽动相位共轭光特性

在KNSBN：Ce晶体中，利用二波耦合作用，在单一光束无法获得相位共轭光的条件下，实现了“猫”式互抽运相位共轭光输出，获得较高的共轭光发射率，实验结果表明，晶体的二波耦合作用可以使晶体的自抽运相位共轭光的阈值光强降低。入射光的入射角范围增大，响应时间缩短。     

Mn替代对Dy2AlFe16-xMnx化合物的结构和磁性的影响

通过X射线衍射及磁测量手段研究了Dy2AlFe16-xMnx化合物的结构和磁性.研究结果表明Dy2AlFe16-xMnx化合物具有六角相的Th2Ni17型结构.对x=1,2的样品采用X射线热膨胀测定法在104-647K的温度范围内测量了其热膨胀性质,发现这些化合物在低温下存在热膨胀反常现象,在居里点附近出现负膨胀性质.对自发磁致伸缩的研究结果表明Dy2AlFe16-xMnx化合物中存在着较强的各向异性的自发磁致伸缩,随着Mn含量的增加,其低温下的自发体磁致伸缩减弱.磁测量结果表明Mn的替代导致Dy2AlFe16-xMnx化合物的居里温度及自发磁化强度急剧下降.     

The stereochemistry of 1,2-additions of allylmagnesium, allylindium, and allylbismuth to cyclohexenones

Allylmagnesium, allylindium, and allylbismuth generally showed a preference for axial addition to cyclohexenones. Allylmagnesium was the most stereoselective. Reactions with an α-methylated enone (carvone) were the most selective, except that allylbismuth was unreactive with this substrate.     

乳液聚合阶段Ⅱ动力学研究的进展

本文简述了乳浓聚合动力学研究的进展,着重于澳大利亚Sydney大学Gilbert等在乳液聚合阶段Ⅱ动力学方面的研究概况。介绍了不同水溶性单体的小尺寸种子乳液体系的SmithEwart递推方程的求解方法及其解析解形式和乳液聚合动力学数据的处理。同时讨论了该研究的局限性。     

基于LiCo0.8M0.2O2 (M=Ni,Zr)薄膜的全固态薄膜锂电池

用射频磁控溅射结合传统退火的方法制备LiCo0.8M0.2O2 (M=Ni,Zr)阴极薄膜．X射线衍射、拉曼光谱、扫描电子显微镜等手段表征了不同掺杂的LiCo0.8M0.2O2薄膜．结果显示,700℃退火的LiCo0.8M0．2O2薄膜具有类似α-NaFeO2的层状结构．通过对不同掺杂锂钴氧阴极的全固态薄膜锂电池Li／LiPON／LiCo0.8M0.2O2的电化学性能研究表明,电化学活性元素Ni的掺杂使全固态电池具有更大的放电容量(56μAh／cm2μm),而非电化学活性元素Zr的掺杂使全固态电池具有更好的循环稳定性．     

最有效的相容剂是两嵌段还是多嵌段聚合物？

采用Monte Carlo模拟方法研究了多嵌段聚合物在A／B／嵌段聚合物三组份体系作为相容剂使用的有效性．占总体积19％的A组份在体系中为分散相．模拟结果显示了两嵌段和多嵌段聚合物在界面上的聚集行为,以及如何影响这个不相容体系的相形为．两嵌段聚合物趋于直立在相界面上,而多嵌段聚合物更容易横跨在相界面上并占据较大的界面积．从而导致多嵌段聚合物更有效的阻止体系相分离的发生．