Relationship between the dynamic softening transition and wet sliding friction of elastomer compounds

For properly chosen elastomer compounds, thermorheological characterization is combined with an examination of the variation of the wet sliding friction with temperature. A conceptual argument leads to the assumption that the wet sliding friction should maximize at the energy dissipation peak associated with the dynamic softening transition at a characteristic frequency determined by the sliding speed and the effective smallest surface asperity scale. The dynamic softening transition is characterized with the peak in tan δ/G′ⁿ, where tan δ is the loss tangent, G′ is the elastic modulus, and n is a constant between 0 and 1. The William–Landel–Ferry transform is uncritically applied for extrapolating the position of the peak in tan δ/G′ⁿ at high frequencies. Even based on the criterion of tan δ, the results obtained on a concrete surface indicate that the effective smallest asperity scale is of order of 100 μm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2467–2478, 2004     

Differential scanning calorimetry and thermogravimetric analysis investigation of the thermal properties and degradation of some radiation‐grafted films and membranes

The influence of irradiation and grafting on the crystallinity of three base polymers has been investigated with differential scanning calorimetry. Grafting has the largest effect on the base polymer crystallinity and results in a reduction of the crystallinity. The thermal degradation of the base polymers and grafted films has been investigated with thermogravimetric analysis. The extent of the fluorination of the base polymer, the irradiation method, and the graft level all influence the thermal degradation and its activation energy. It is proposed that the variation of the chain lengths of the grafted polystyrene chains is actually a primary underlying factor responsible for the influence of these various parameters on the degradation process. The first results of a comparative thermal analysis of some fuel‐cell membranes are also presented, and the promise and shortcomings of this method are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2612–2624, 2004     

Colorimetric recognition of different enzymology-concerning transition metals based on a hybrid cluster complex.

A hybrid cluster complex, formed by chelating a chromogenic ligand to a [2Fe-2S] cluster, sensitively exhibited differential colorimetric responses towards Hg2+, Cd2+, Cr3+, Pb2, Sn2+, Cu2+, Zn2+, Fe3+ and Co2+ in water at physiological pH. Speciation of some of these metal elements, such as Cr(III) and Sn(IV), was also studied by UV/Vis absorption.     

NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.     

光学非球面二次曲面常数及顶点曲率的研究

受光学非球面制造过程中诸工艺参数的影响,能否保证非球面顶点曲率及二次曲面常数的精度是一个重要问题。基于二次曲面方程,推导出确定光学非球面二次曲面常数k以及顶点曲率半径r的一组算法,并在对一块口径为760mm×200mm标准非球面反射镜的实际测算中进行拟合,经过优化,拟合精度达到Δk=0.015,Δr=0.341mm,从而有效的控制了光学非球面制造过程中的顶点曲率及二次曲面常数的偏差。     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

Dynamic boundary stabilization of a Reissner–Mindlin plate with Timoshenko beam

This paper is concerned with well‐posedness results for a mathematical model for the transversal vibrations of a two‐dimensional hybrid elastic structure consisting of a rectangular Reissner–Mindlin plate with a Timoshenko beam attached to its free edge. The model incorporates linear dynamic feedback controls along the interface between the plate and the beam. Classical semigroup methods are employed to show the unique solvability of the coupled initial‐boundary‐value problem. We also show that the energy associated with the system exhibits the property of strong stability. Copyright © 2004 John Wiley & Sons, Ltd.     

Stability Conditions of the MMAP [ K ]/ G [ K ]/1/ LCFS Preemptive Repeat Queue

In this paper, we study the stability conditions of the MMAP[K]/G[K]/1/LCFS preemptive repeat queue. We introduce an embedded Markov chain of matrix M/G/1 type with a tree structure and identify conditions for the Markov chain to be ergodic. First, we present three conventional methods for the stability problem of the queueing system of interest. These methods are either computationally demanding or do not provide accurate information for system stability. Then we introduce a novel approach that develops two linear programs whose solutions provide sufficient conditions for stability or instability of the queueing system. The new approach is numerically efficient. The advantages and disadvantages of the methods introduced in this paper are analyzed both theoretically and numerically.     

In-time motion adjustment in laser cladding manufacturing process for improving dimensional accuracy and surface finish of the formed part

This paper presents in-time motion adjustment in laser cladding manufacturing process as a means to improve dimensional accuracy and surface finish of the built part. Defects occurring during laser cladding degrade the part quality such as dimensional accuracy and surface finish. In this paper, in-time motion adjustment strategy was presented to remedy and eliminate defects occurring during laser cladding to improve the dimensional accuracy and surface finish. Based on the relationship between the motion of laser head relative to the growing part and other parameters in effects on clad profile, the laser traverse speed, stand-off distance and laser approach orientation to the existing clad layer were adjusted by instructions from a close-loop control system in real time to remedy and eliminate defects. The results of the experiments verified the effects of in-time motion adjustment on dimensional accuracy and surface finish.